Android now supports devices with 512MB of RAM. This documentation is intended to help OEMs optimize and configure Android 4.4 for low-memory devices. Several of these optimizations are generic enough that they can be applied to previous releases as well.
Android 4.4 platform optimizations
Improved memory management
- Validated memory-saving kernel configurations: Swap to ZRAM.
- Kill cached processes if about to be uncached and too large.
- Don't allow large services to put themselves back into A Services (so they can't cause the launcher to be killed).
- Kill processes (even ordinarily unkillable ones such as the current IME) that get too large in idle maintenance.
- Serialize the launch of background services.
- Tuned memory use of low-RAM devices: tighter out-of-memory (OOM) adjustment levels, smaller graphics caches, etc.
Reduced system memory
- Trimmed system_server and SystemUI processes (saved several MBs).
- Preload dex caches in Dalvik (saved several MBs).
- Validated JIT-off option (saves up to 1.5MB per process).
- Reduced per-process font cache overhead.
- Introduced ArrayMap/ArraySet and used extensively in framework as a lighter-footprint replacement for HashMap/HashSet.
Added a new Developer Option to show memory state and application memory usage ranked by how often they run and amount of memory consumed.
Added a new ActivityManager.isLowRamDevice() to allow applications to detect when running on low memory devices and choose to disable large-RAM features.
New memtrack HAL to track graphics memory allocations, additional information
dumpsys meminfo, clarified summaries in meminfo (for example reported free
RAM includes RAM of cached processes, so that OEMs don't try to optimize the
Enable Low Ram Device flag
We are introducing a new API called
ActivityManager.isLowRamDevice() for applications to determine if
they should turn off specific memory-intensive
features that work poorly on low-memory devices.
For 512MB devices, this API is expected to return
true. It can be enabled by
the following system property in the device makefile.
PRODUCT_PROPERTY_OVERRIDES += ro.config.low_ram=true
Ensure the default wallpaper setup on launcher is not using live-wallpaper. Low-memory devices should not pre-install any live wallpapers.
Tuning kernel/ActivityManager to reduce direct reclaim
Direct reclaim happens when a process or the kernel tries to allocate a page
of memory (either directly or due to faulting in a new page) and the kernel
has used all available free memory. This requires the kernel to block the
allocation while it frees up a page. This in turn often requires disk I/O to
flush out a dirty file-backed page or waiting for
lowmemorykiller to kill a
process. This can result in extra I/O in any thread, including a UI thread.
To avoid direct reclaim, the kernel has watermarks that trigger
background reclaim. This is a thread that tries to free up pages so the next
time a real thread allocates it can succeed quickly.
The default threshold to trigger background reclaim is fairly low, around 2MB on a 2GB device and 636KB on a 512MB device. And the kernel reclaims only a few MB of memory in background reclaim. This means any process that quickly allocates more than a few megabytes is going to quickly hit direct reclaim.
Support for a new kernel tunable is added in the android-3.4 kernel branch as patch 92189d47f66c67e5fd92eafaa287e153197a454f ("add extra free kbytes tunable"). Cherry-picking this patch to a device's kernel will allow ActivityManager to tell the kernel to try to keep 3 full-screen 32 bpp buffers of memory free.
These thresholds can be configured via the framework config.xml
<!-- Device configuration setting the /proc/sys/vm/extra_free_kbytes tunable in the kernel (if it exists). A high value will increase the amount of memory that the kernel tries to keep free, reducing allocation time and causing the lowmemorykiller to kill earlier. A low value allows more memory to be used by processes but may cause more allocations to block waiting on disk I/O or lowmemorykiller. Overrides the default value chosen by ActivityManager based on screen size. 0 prevents keeping any extra memory over what the kernel keeps by default. -1 keeps the default. --> <integer name="config_extraFreeKbytesAbsolute">-1</integer>
<!-- Device configuration adjusting the /proc/sys/vm/extra_free_kbytes tunable in the kernel (if it exists). 0 uses the default value chosen by ActivityManager. A positive value will increase the amount of memory that the kernel tries to keep free, reducing allocation time and causing the lowmemorykiller to kill earlier. A negative value allows more memory to be used by processes but may cause more allocations to block waiting on disk I/O or lowmemorykiller. Directly added to the default value chosen by ActivityManager based on screen size. --> <integer name="config_extraFreeKbytesAdjust">0</integer>
ActivityManager configures the thresholds of the LowMemoryKiller to match its expectation of the working set of file-backed pages (cached pages) required to run the processes in each priority level bucket. If a device has high requirements for the working set, for example if the vendor UI requires more memory or if more services have been added, the thresholds can be increased.
The thresholds can be reduced if too much memory is being reserved for file backed pages, so that background processes are being killed long before disk thrashing would occur due to the cache getting too small.
<!-- Device configuration setting the minfree tunable in the lowmemorykiller in the kernel. A high value will cause the lowmemorykiller to fire earlier, keeping more memory in the file cache and preventing I/O thrashing, but allowing fewer processes to stay in memory. A low value will keep more processes in memory but may cause thrashing if set too low. Overrides the default value chosen by ActivityManager based on screen size and total memory for the largest lowmemorykiller bucket, and scaled proportionally to the smaller buckets. -1 keeps the default. --> <integer name="config_lowMemoryKillerMinFreeKbytesAbsolute">-1</integer>
<!-- Device configuration adjusting the minfree tunable in the lowmemorykiller in the kernel. A high value will cause the lowmemorykiller to fire earlier, keeping more memory in the file cache and preventing I/O thrashing, but allowing fewer processes to stay in memory. A low value will keep more processes in memory but may cause thrashing if set too low. Directly added to the default value chosen by ActivityManager based on screen size and total memory for the largest lowmemorykiller bucket, and scaled proportionally to the smaller buckets. 0 keeps the default. --> <integer name="config_lowMemoryKillerMinFreeKbytesAdjust">0</integer>
Swap to zRAM
zRAM swap can increase the amount of memory available in the system by compressing memory pages and putting them in a dynamically allocated swap area of memory.
Again, since this is trading off CPU time for a small increase in memory, you should be careful about measuring the performance impact zRAM swap has on your system.
Android handles swap to zRAM at several levels:
- First, the following kernel options must be enabled to use zRAM swap
- Then, you should add a line that looks like this to your fstab:
/dev/block/zram0 none swap defaults zramsize=<size in bytes>,swapprio=<swap partition priority>
zramsizeis mandatory and indicates how much uncompressed memory you want the zram area to hold. Compression ratios in the 30-50% range are usually observed.
swappriois optional and not needed if you don't have more than one swap area.
You should also be sure to label the associated block device as a swap_block_device in the device-specific sepolicy/file_contexts so that it is treated properly by SELinux.
- By default, the Linux kernel swaps in 8 pages of memory at a time. When
using ZRAM, the incremental cost of reading 1 page at a time is negligible
and may help in case the device is under extreme memory pressure. To read
only 1 page at a time, add the following to your
write /proc/sys/vm/page-cluster 0
- In your
mount_all /fstab.Xline, add:
- The memory cgroups are automatically configured at boot time if the feature is enabled in kernel.
- If memory cgroups are available, the ActivityManager will mark lower priority threads as being more swappable than other threads. If memory is needed, the Android kernel will start migrating memory pages to zRAM swap, giving a higher priority to those memory pages that have been marked by ActivityManager.
Carveouts, Ion and Contiguous Memory Allocation (CMA)
It is especially important on low memory devices to be mindful about carveouts, especially those that will not always be fully utilized -- for example a carveout for secure video playback. There are several solutions to minimizing the impact of your carveout regions that depend on the exact requirements of your hardware.
If hardware permits discontiguous memory allocations, the ion system heap allows memory allocations from system memory, eliminating the need for a carveout. It also attempts to make large allocations to eliminate TLB pressure on peripherals. If memory regions must be contiguous or confined to a specific address range, the contiguous memory allocator (CMA) can be used.
This creates a carveout that the system can also use of for movable pages. When the region is needed, movable pages will be migrated out of it, allowing the system to use a large carveout for other purposes when it is free. CMA can be used directly or more simply via ion by using the ion cma heap.
Application optimization tips
- Review Managing your App's Memory and these past blog posts on the same topic:
- Check/remove any unused assets from preinstalled apps - development/tools/findunused (should help make the app smaller).
- Use PNG format for assets, especially when they have transparent areas
- If writing native code, use calloc() rather than malloc/memset
- Don't enable code that is writing Parcel data to disk and reading it later.
- Don't subscribe to every package installed, instead use ssp filtering. Add
filtering like below:
<data android:scheme="package" android:ssp="com.android.pkg1" /> <data android:scheme="package" android:ssp="com.myapp.act1" />
Understand the various process states in Android
SERVICE - SERVICE_RESTARTING
Applications that are making themselves run in the background for their own reason. Most common problem apps have when they run in the background too much. %duration * pss is probably a good "badness" metric, although this set is so focused that just doing %duration is probably better to focus on the fact that we just don't want them running at all.
IMPORTANT_FOREGROUND - RECEIVER
Applications running in the background (not directly interacting with the user) for any reason. These all add memory load to the system. In this case the (%duration * pss) badness value is probably the best ordering of such processes, because many of these will be always running for good reason, and their pss size then is very important as part of their memory load.
Persistent system processes. Track pss to watch for these processes getting too large.
Process the user is currently interacting with. Again, pss is the important metric here, showing how much memory load the app is creating while in use.
HOME - CACHED_EMPTY
All of these processes at the bottom are ones that the system is keeping around in case they are needed again; but they can be freely killed at any time and re-created if needed. These are the basis for how we compute the memory state -- normal, moderate, low, critical is based on how many of these processes the system can keep around. Again the key thing for these processes is the pss; these processes should try to get their memory footprint down as much as possible when they are in this state, to allow for the maximum total number of processes to be kept around. Generally a well behaved app will have a pss footprint that is significantly smaller when in this state than when TOP.
TOP vs. CACHED_ACTIVITY-CACHED_ACTIVITY_CLIENT
The difference in pss between when a process is TOP vs. when it is in either of these specific cached states is the best data for seeing how well it is releasing memory when going into the background. Excluding CACHED_EMPTY state makes this data better, since it removes situations when the process has started for some reasons besides doing UI and so will not have to deal with all of the UI overhead it gets when interacting with the user.
Analyzing app startup time
$ adb shell am start with the
--start-profiler option to run the profiler when your app starts.
This will start the profiler almost immediately after your process is forked
from zygote, before any of your code is loaded into it.
Analyze using bugreports
Now contains various information that can be used for debugging. The
usagestats. You can find them with
lines like this:
------ CHECKIN BATTERYSTATS (dumpsys batterystats --checkin) ------ 7,0,h,-2558644,97,1946288161,3,2,0,340,4183 7,0,h,-2553041,97,1946288161,3,2,0,340,4183
Check for any persistent processes
Reboot the device and check the processes.
Run for a few hours and check the processes again. There should not be any long running processes.
Run longevity tests
Run for longer durations and track the memory of the process. Does it increase? Does it stay constant? Create Canonical use cases and run longevity tests on these scenarios.