In the L release of Android, we are halting support for some sensor HAL
versions. The only supported versions are
In the next releases, we are likely to drop support for 1_0 as well.
1_0 has no concept of batching. If possible, all devices using 1_0 SHOULD upgrade to 1_3.
1_1 and 1_2 suffer from poor definition of the batching concept, and are not supported anymore
All devices currently using 1_1 or 1_2 MUST upgrade to 1_3.
In 1_3, we simplified the notion of batching, and we introduced wake up sensors.
To upgrade to 1_3, follow the changes listed below.
Implement the batch function
Even if you do not implement batching (your hardware has no FIFO), you must
batch is used to set
the sampling period and the maximum reporting latency for a given sensor. It
setDelay will not be called
If you do not implement batching, you can implement
simply calling your existing
setDelay function with the provided
Implement the flush function
Even if you do not implement batching, you must implement the
If you do not implement batching,
flush must generate one
META_DATA_FLUSH_COMPLETE event and return 0 (success).
Change your sensors_poll_device_t.common.version
your_poll_device.common.version = SENSORS_DEVICE_API_VERSION_1_3
Add the new fields to the definition of your sensors
When defining each sensor, in addition to the usual sensor_t fields:
.name = "My magnetic field Sensor", .vendor = "My company", .version = 1, .handle = mag_handle, .type = SENSOR_TYPE_MAGNETIC_FIELD, .maxRange = 200.0f, .resolution = CONVERT_M, .power = 5.0f, .minDelay = 16667,
you also must set the new fields, defined between 1_0 and 1_3:
.fifoReservedEventCount = 0, .fifoMaxEventCount = 0, .stringType = 0, .requiredPermission = 0, .maxDelay = 200000 .flags = SENSOR_FLAG_CONTINUOUS_MODE,
fifoReservedEventCount: If not implementing batching, set this one to 0.
fifoMaxEventCount: If not implementing batching, set this one to 0
stringType: Set to 0 for all official android sensors (those that are defined in sensors.h), as this value will be overwritten by the framework. For non-official sensors, see sensor_t for details on how to set it.
requiredPermission: This is the permission that applications will be required to have to get
access to your sensor. You can usually set this to 0 for all of your sensors,
but sensors with type
HEART_RATE must set this to
maxDelay: This value is important and you will need to set it according to the capabilities of the sensor and of its driver.
This value is defined only for continuous and on-change sensors. It is the
delay between two sensor events corresponding to the lowest frequency that this
sensor supports. When lower frequencies are requested through the
batch function, the events will be generated at this frequency
instead. It can be used by the framework or applications to estimate when the
batch FIFO may be full. If this value is not set properly, CTS will fail.
For one-shot and special reporting mode sensors, set
maxDelay to 0.
For continuous sensors, set it to the maximum sampling period allowed in microseconds.
The following are applicable for
period_nsis in nanoseconds whereas
minDelayare in microseconds.
maxDelayshould always fit within a 32-bit signed integer. It is declared as 64-bit on 64-bit architectures only for binary compatibility reasons.
flags: This field defines the reporting mode of the sensor and whether the sensor is a wake up sensor.
If you do not implement batching, and are just moving from 1.0 to 1.3, set this to:
SENSOR_FLAG_WAKE_UP | SENSOR_FLAG_ONE_SHOT_MODE for one-shot
SENSOR_FLAG_CONTINUOUS_MODE for continuous
SENSOR_FLAG_ON_CHANGE_MODE for on-change
sensors except proximity
SENSOR_FLAG_SPECIAL_REPORTING_MODE for sensors with special
reporting mode except for the tilt
Notes when upgrading from 1_1 or 1_2
batchfunction now nearly-always succeeds, even for sensors that do not support batching, independent of the value of the timeout argument. The only cases where the
batchfunction might fail are internal errors, or a bad
- Whether a sensor supports batching is defined by whether it has a
fifoMaxEventCountgreater than 0. (In previous versions, it was based on the return value of
- Sensors that support batching are always in what we called the “batch
mode” in previous versions: even if the
max_report_latency_nsparameter is 0, the sensor must still be batched, meaning the events must be stored in the FIFO when the SoC goes to suspend mode.
flagsparameter of the
batchfunction is not used anymore.
WAKE_UPON_FIFO_FULLare both deprecated, and will never be passed to the
- The batch timeout argument is now referred to as the