1. Giriş
Bu belgede, cihazların Android 12 ile uyumlu olabilmesi için karşılanması gereken gereksinimler sıralanmaktadır.
"ZORUNLU", "OLMAMALIDIR", "ZORUNLU", "OLACAKTIR", "OLMAYACAKTIR", "YAPMALIDIR", "OLMAMALIDIR", "ÖNERİLİR", "MAY" ve "İSTEĞE BAĞLI" ifadelerinin kullanımı IETF'ye göredir. RFC2119'da tanımlanan standart.
Bu belgede kullanıldığı şekliyle "cihaz uygulayıcısı" veya "uygulayıcı", Android 12 çalıştıran bir donanım/yazılım çözümü geliştiren kişi veya kuruluştur. "Cihaz uygulaması" veya "uygulama", bu şekilde geliştirilen donanım/yazılım çözümüdür.
Android 12 ile uyumlu sayılması için cihaz uygulamalarının, referans yoluyla dahil edilen tüm belgeler de dahil olmak üzere bu Uyumluluk Tanımında sunulan gereksinimleri karşılaması GEREKİR.
Bu tanımın veya bölüm 10'da açıklanan yazılım testlerinin sessiz, belirsiz veya eksik olduğu durumlarda, mevcut uygulamalarla uyumluluğun sağlanması cihaz uygulayıcısının sorumluluğundadır.
Bu nedenle Android Açık Kaynak Projesi , Android'in hem referansı hem de tercih edilen uygulamasıdır. Cihaz uygulayıcılarının, uygulamalarını mümkün olan en geniş ölçüde Android Açık Kaynak Projesi'nde bulunan "yukarı akış" kaynak koduna dayandırmaları ŞİDDETLE TAVSİYE EDİLİR. Bazı bileşenler varsayımsal olarak alternatif uygulamalarla değiştirilebilirken, yazılım testlerini geçmek büyük ölçüde zorlaşacağından bu uygulamaya uyulmaması KESİNLİKLE TAVSİYE EDİLİR. Uyumluluk Test Paketi dahil ve ötesinde, standart Android uygulamasıyla tam davranışsal uyumluluğun sağlanması uygulayıcının sorumluluğundadır. Son olarak, belirli bileşen değişikliklerinin ve modifikasyonlarının bu belgede açıkça yasaklandığını unutmayın.
Bu belgede bağlantısı verilen kaynakların çoğu, doğrudan veya dolaylı olarak Android SDK'dan türetilmiştir ve işlevsel olarak söz konusu SDK'nın belgelerindeki bilgilerle aynı olacaktır. Bu Uyumluluk Tanımının veya Uyumluluk Test Paketinin SDK belgeleriyle uyuşmadığı durumlarda, SDK belgeleri yetkili kabul edilir. Bu belge boyunca bağlantılı kaynaklarda sağlanan tüm teknik ayrıntılar, dahil edilerek bu Uyumluluk Tanımının bir parçası olarak kabul edilir.
1.1 Belge Yapısı
1.1.1. Cihaz Türüne Göre Gereksinimler
Bölüm 2, belirli bir cihaz tipine uygulanan tüm gereklilikleri içermektedir. Bölüm 2'nin her alt bölümü belirli bir cihaz tipine ayrılmıştır.
Tüm Android cihaz uygulamalarına evrensel olarak uygulanan diğer tüm gereksinimler, Bölüm 2'den sonraki bölümlerde listelenmiştir. Bu gereksinimlere bu belgede "Temel Gereksinimler" adı verilmektedir.
1.1.2. Gereksinim Kimliği
MUST gereksinimleri için gereksinim kimliği atanır.
- Kimlik yalnızca MUST gereksinimleri için atanır.
- KESİNLİKLE ÖNERİLEN gereksinimler [SR] olarak işaretlenmiştir ancak kimlik atanmamıştır.
- Kimlik aşağıdakilerden oluşur: Cihaz Tipi Kimliği - Durum Kimliği - Gereksinim Kimliği (örn. C-0-1).
Her kimlik aşağıdaki gibi tanımlanır:
- Cihaz Türü Kimliği ( 2. Cihaz Türleri bölümünde daha fazlasını görün)
- C: Çekirdek (Tüm Android cihaz uygulamalarına uygulanan gereksinimler)
- H: Android El Tipi cihaz
- T: Android Televizyon cihazı
- C: Android Otomotiv uygulaması
- W: Android Watch uygulaması
- Sekme: Android Tablet uygulaması
- Durum Kimliği
- Gereksinim koşulsuz olduğunda bu ID 0 olarak ayarlanır.
- Gereksinim koşullu olduğunda 1. koşula 1 atanır ve aynı bölüm ve aynı cihaz tipinde sayı 1 artar.
- Gereksinim Kimliği
- Bu ID 1'den başlar ve aynı bölüm ve aynı koşul içerisinde 1'er artar.
1.1.3. Bölüm 2'deki Gereksinim Kimliği
Bölüm 2'deki Gereksinim Kimlikleri iki bölümden oluşur. Birincisi yukarıda açıklandığı gibi bir bölüm kimliğine karşılık gelir. İkinci bölüm form faktörünü ve form faktörüne özel gereksinimi tanımlar.
yukarıda açıklanan Gereksinim Kimliği tarafından takip edilen bölüm kimliği.
- Bölüm 2'deki kimlik aşağıdakilerden oluşur: Bölüm Kimliği / Cihaz Tipi Kimliği - Durum Kimliği - Gereksinim Kimliği (örn. 7.4.3/A-0-1).
2. Cihaz Türleri
Android Açık Kaynak Projesi, çeşitli cihaz türleri ve form faktörleri için kullanılabilecek bir yazılım yığını sağlar. Cihazlarda güvenliği desteklemek için, herhangi bir yedek işletim sistemi veya alternatif çekirdek uygulaması da dahil olmak üzere yazılım yığınının, bölüm 9'da ve bu CDD'nin başka yerlerinde açıklandığı gibi güvenli bir ortamda yürütülmesi beklenir. Nispeten daha iyi kurulmuş bir uygulama dağıtım ekosistemine sahip birkaç cihaz türü vardır.
Bu bölümde bu cihaz tipleri ve her cihaz tipi için geçerli olan ek gereksinimler ve öneriler açıklanmaktadır.
Açıklanan cihaz türlerinden herhangi birine uymayan tüm Android cihaz uygulamalarının yine de bu Uyumluluk Tanımının diğer bölümlerindeki tüm gereksinimleri karşılaması ZORUNLUDUR.
2.1 Cihaz Konfigürasyonları
Cihaz türüne göre donanım yapılandırmasındaki büyük farklılıklar için bu bölümde yer alan cihaza özel gereksinimlere bakın.
2.2. Elde Taşınabilir Gereksinimler
Android El Tipi cihaz, mp3 çalar, telefon veya tablet gibi genellikle elde tutularak kullanılan bir Android cihaz uygulamasını ifade eder.
Android cihaz uygulamaları, aşağıdaki kriterlerin tümünü karşılamaları durumunda Elde Taşınabilir olarak sınıflandırılır:
- Pil gibi hareket kabiliyeti sağlayan bir güç kaynağına sahip olun.
- 3,3 inç (veya API düzeyi 29 veya daha önceki sürümlerde gönderilen cihaz uygulamaları için 2,5 inç) ila 8 inç aralığında fiziksel çapraz ekran boyutuna sahip olun.
Bu bölümün geri kalanındaki ek gereksinimler Android Handheld cihaz uygulamalarına özeldir.
2.2.1. Donanım
Elde taşınır cihaz uygulamaları:
- [ 7.1 .1.1/H-0-1] Bu belgede açıklanan tüm gereksinimleri karşılayan en az bir Android uyumlu ekrana sahip OLMALIDIR.
[ 7.1 .1.3/H-SR-1] Kullanıcılara ekran boyutunu (ekran yoğunluğunu) değiştirme olanağı sağlamak için KESİNLİKLE TAVSİYE EDİLİR.
[ 7.1 .1.1/H-0-2] En azından herhangi bir yerleşik ekranın en yüksek çözünürlüğü kadar büyük grafik arabelleklerinin GPU bileşimini desteklemelidir ZORUNLU.
Elde taşınır cihaz uygulamaları yazılım ekranı döndürmeyi destekliyorsa:
- [ 7.1 .1.1/H-1-1]* Üçüncü taraf uygulamaları için sağlanan mantıksal ekranın kısa kenar(lar)da en az 2 inç ve uzun kenar(lar)da 2,7 inç olması ZORUNLUDUR. Android API düzeyi 29 veya daha önceki bir sürümle gönderilen cihazlar bu gereklilikten muaf OLABİLİR.
Elde taşınır cihaz uygulamaları yazılım ekranı döndürmeyi desteklemiyorsa:
- [ 7.1 .1.1/H-2-1]* Üçüncü taraf uygulamaları için sağlanan mantıksal ekranın kısa kenar(lar)da en az 2,7 inç olması ZORUNLUDUR. Android API düzeyi 29 veya daha önceki bir sürümle gönderilen cihazlar bu gereklilikten muaf OLABİLİR.
El tipi cihaz uygulamaları, Configuration.isScreenHdr()
aracılığıyla yüksek dinamik aralıklı ekranlar için destek talep ederse:
- [ 7.1 .4.5/H-1-1]
EGL_EXT_gl_colorspace_bt2020_pq
,EGL_EXT_surface_SMPTE2086_metadata
,EGL_EXT_surface_CTA861_3_metadata
,VK_EXT_swapchain_colorspace
veVK_EXT_hdr_metadata
uzantılarına yönelik desteğin reklamı ZORUNLUDUR .
Elde taşınır cihaz uygulamaları:
- [ 7.1 .4.6/H-0-1]
graphics.gpu.profiler.support
sistem özelliği aracılığıyla cihazın GPU profil oluşturma özelliğini destekleyip desteklemediğini bildirmesi ZORUNLUDUR.
Taşınabilir aygıt uygulamaları, graphics.gpu.profiler.support
sistem özelliği aracılığıyla destek beyan ederse:
- [ 7.1 .4.6/H-1-1] Perfetto belgelerinde tanımlanan GPU sayaçları ve GPU işleme aşamaları şemasına uygun bir protobuf izlemesini çıktı olarak rapor etmelidir ZORUNLU.
- [ 7.1 .4.6/H-1-2] GPU sayacı izleme paketi protokolünü takip ederek cihazın GPU sayaçları için uyumlu değerleri rapor etmelidir ZORUNLU.
- [ 7.1 .4.6/H-1-3] İşleme aşaması izleme paketi protokolünü takiben aygıtın GPU RenderStages'i için uyumlu değerleri rapor etmesi ZORUNLUDUR.
- [ 7.1 .4.6/H-1-4] Şu formatta belirtildiği gibi bir GPU Frekansı izleme noktasının bildirilmesi ZORUNLUDUR: power/gpu_frequency .
Elde taşınır cihaz uygulamaları:
- [ 7.1 .5/H-0-1] Yukarı akışlı Android açık kaynak kodu tarafından uygulanan eski uygulama uyumluluk modu desteğini içermelidir ZORUNLU. Yani, cihaz uygulamalarının uyumluluk modunun etkinleştirildiği tetikleyicileri veya eşikleri DEĞİŞTİRMEMELİ ve uyumluluk modunun davranışını DEĞİŞTİRMEMELİDİR.
- [ 7.2 .1/H-0-1] Üçüncü taraf Giriş Yöntemi Düzenleyicisi (IME) uygulamaları için destek içermelidir ZORUNLU.
- [ 7.2 .3/H-0-3] Ana ekranı sağlayan tüm Android uyumlu ekranlarda Ana Sayfa işlevini sağlamalıdır ZORUNLU.
- [ 7.2 .3/H-0-4] Tüm Android uyumlu ekranlarda Geri işlevini ve Android uyumlu ekranlardan en az birinde Son Kullanılanlar işlevini SAĞLAMALIDIR.
- [ 7.2 .3/H-0-2] Geri işlevinin (
KEYCODE_BACK
) hem normal hem de uzun basma olayını ön plandaki uygulamaya GÖNDERMELİDİR. Bu olaylar sistem tarafından tüketilmemelidir ve Android cihazının dışından (örn. Android cihazına bağlı harici donanım klavyesi) tetiklenebilir. - [ 7.2 .4/H-0-1] Dokunmatik ekran girişini desteklemelidir ZORUNLU.
- [ 7.2 .4/H-SR-1] Kullanıcı tarafından seçilen yardım uygulamasını, başka bir deyişle VoiceInteractionService'i uygulayan uygulamayı veya ön plan etkinliği ise
KEYCODE_MEDIA_PLAY_PAUSE
veyaKEYCODE_HEADSETHOOK
tuşuna uzun basıldığındaACTION_ASSIST
işleyen bir etkinliği başlatmanız KESİNLİKLE ÖNERİLİR bu uzun basış olaylarını işlemez. - [ 7.3 .1/H-SR-1] 3 eksenli bir ivmeölçer içermesi KESİNLİKLE TAVSİYE EDİLİR.
Taşınabilir cihaz uygulamaları 3 eksenli bir ivmeölçer içeriyorsa:
- [ 7.3.1 /H-1-1] En az 100 Hz frekansa kadar olan olayları rapor edebilmelidir ZORUNLU.
Elde taşınır cihaz uygulamaları bir GPS/GNSS alıcısı içeriyorsa ve bu özelliği uygulamalara android.hardware.location.gps
özellik işareti aracılığıyla rapor ediyorsa, bunlar:
- [ 7.3 .3/H-2-1] GPS/GNSS'den hesaplanan konum henüz rapor edilmemiş olsa bile, GNSS ölçümlerini bulunur bulunmaz rapor etmelidir.
- [ 7.3 .3/H-2-2] Konumu belirledikten sonra, açık gökyüzü koşullarında, sabit veya saniyede 0,2 metre kareden daha az ivmeyle hareket halindeyken hesaplamak için yeterli olan GNSS sözde mesafelerini ve sözde mesafe oranlarını rapor etmelidir. zamanın en az %95'inde konum 20 metre ve hız 0,2 metre/saniye dahilinde olmalıdır.
Elde taşınır cihaz uygulamaları 3 eksenli bir jiroskop içeriyorsa:
- [ 7.3 .4/H-3-1] En az 100 Hz frekansa kadar olan olayları rapor edebilmelidir ZORUNLU.
- [ 7.3 .4/H-3-2] Saniyede 1000 dereceye kadar yönelim değişikliklerini ölçebilme kapasitesine sahip OLMALIDIR.
Sesli arama yapabilen ve getPhoneType
PHONE_TYPE_NONE
dışında herhangi bir değeri gösterebilen elde taşınır cihaz uygulamaları:
- [ 7.3 .8/H] Yakınlık sensörü OLMALIDIR.
Elde taşınır cihaz uygulamaları:
- [ 7.3 .11/H-SR-1] Poz sensörünün 6 serbestlik derecesine sahip olarak desteklenmesi ÖNERİLİR.
- [ 7.4 .3/H] Bluetooth ve Bluetooth LE desteğini içermelidir.
Elde taşınır cihaz uygulamaları tarifeli bir bağlantı içeriyorsa:
- [ 7.4 .7/H-1-1] Veri tasarrufu modunu sağlaması ZORUNLUDUR.
Elde taşınır cihaz uygulamaları, CameraMetadata.REQUEST_AVAILABLE_CAPABILITIES_LOGICAL_MULTI_CAMERA
kullanan yetenekleri listeleyen bir mantıksal kamera cihazı içeriyorsa, bunlar:
- [ 7.5 .4/H-1-1] Varsayılan olarak normal görüş alanına (FOV) sahip OLMALIDIR ve 50 ila 95 derece arasında OLMALIDIR.
Elde taşınır cihaz uygulamaları:
- [ 7.6 .1/H-0-1] Uygulama özel verileri (aka "/data" bölümü) için en az 4 GB kalıcı depolama alanına sahip olması GEREKİR.
- [ 7.6 .1/H-0-2] Çekirdek ve kullanıcı alanında 1 GB'den az bellek mevcut olduğunda
ActivityManager.isLowRamDevice()
için "true" değerini döndürmesi ZORUNLUDUR.
Elde taşınır cihaz uygulamaları yalnızca 32 bit ABI'yi desteklediğini beyan ederse:
[ 7.6 .1/H-1-1] Varsayılan ekran qHD'ye kadar çerçeve arabellek çözünürlükleri kullanıyorsa (örn. FWVGA), çekirdek ve kullanıcı alanı için kullanılabilir bellek en az 416 MB OLMALIDIR.
[ 7.6 .1/H-2-1] Eğer varsayılan ekran HD+'ya kadar (örn. HD, WSVGA) çerçeve ara bellek çözünürlüklerini kullanıyorsa, çekirdek ve kullanıcı alanı tarafından kullanılabilen bellek en az 592 MB OLMALIDIR.
[ 7.6 .1/H-3-1] Varsayılan ekran FHD'ye kadar çerçeve arabellek çözünürlükleri kullanıyorsa (örn. WSXGA+) çekirdek ve kullanıcı alanı için kullanılabilir bellek en az 896 MB OLMALIDIR.
[ 7.6 .1/H-4-1] Varsayılan ekran QHD'ye kadar çerçeve arabellek çözünürlükleri kullanıyorsa (örn. QWXGA) çekirdek ve kullanıcı alanı için mevcut bellek en az 1344 MB OLMALIDIR.
Elde taşınır cihaz uygulamaları herhangi bir 64 bit ABI'yi (32 bit ABI ile veya 32 bit ABI olmadan) desteklediğini beyan ederse:
[ 7.6 .1/H-5-1] Varsayılan ekran qHD'ye kadar çerçeve arabellek çözünürlükleri kullanıyorsa (örn. FWVGA), çekirdek ve kullanıcı alanı için kullanılabilir bellek en az 816 MB OLMALIDIR.
[ 7.6 .1/H-6-1] Eğer varsayılan ekran HD+'a kadar (örn. HD, WSVGA) çerçeve ara bellek çözünürlüklerini kullanıyorsa, çekirdek ve kullanıcı alanı tarafından kullanılabilen bellek en az 944 MB OLMALIDIR.
[ 7.6 .1/H-7-1] Varsayılan ekran FHD'ye kadar çerçeve arabellek çözünürlükleri kullanıyorsa (örn. WSXGA+) çekirdek ve kullanıcı alanı için kullanılabilir bellek en az 1280 MB OLMALIDIR.
[ 7.6 .1/H-8-1] Varsayılan ekran QHD'ye kadar çerçeve arabellek çözünürlükleri kullanıyorsa (örn. QWXGA), çekirdek ve kullanıcı alanı için mevcut bellek en az 1824 MB OLMALIDIR.
Yukarıdaki "çekirdek ve kullanıcı alanı tarafından kullanılabilen bellek" ifadesinin, aygıt uygulamalarında çekirdeğin kontrolü altında olmayan radyo, video vb. donanım bileşenlerine halihazırda ayrılmış herhangi bir belleğe ek olarak sağlanan bellek alanını ifade ettiğini unutmayın.
Elde taşınır cihaz uygulamaları, çekirdek ve kullanıcı alanı için 1 GB'a eşit veya daha az bellek içeriyorsa, bunlar:
- [ 7.6 .1/H-9-1]
android.hardware.ram.low
özellik işaretini bildirmesi ZORUNLUDUR. - [ 7.6 .1/H-9-2] Uygulama özel verileri (aka "/data" bölümü) için en az 1,1 GB kalıcı depolama alanına sahip olması GEREKİR.
Elde taşınır cihaz uygulamaları, çekirdek ve kullanıcı alanı için 1 GB'den fazla kullanılabilir bellek içeriyorsa, bunlar:
- [ 7.6 .1/H-10-1] Uygulama özel verileri (diğer adıyla "/data" bölümü) için en az 4 GB kalıcı depolama alanına sahip olması GEREKİR.
- özellik bayrağını
android.hardware.ram.normal
olarak bildirmeniz GEREKİR.
Elde taşınır cihaz uygulamaları, çekirdek ve kullanıcı alanı için 2 GB'ye eşit veya daha büyük ve 4 GB'den daha az bellek içeriyorsa, bunlar:
- [7.6.1/H-SR-1] Yalnızca 32 bit kullanıcı alanını (hem uygulamalar hem de sistem kodu) desteklemeleri KESİNLİKLE ÖNERİLİR
Elde taşınır cihaz uygulamaları, çekirdek ve kullanıcı alanı için 2 GB'den daha az bellek içeriyorsa, bunlar:
- [7.6.1/H-1-1] yalnızca 32 bit ABI'leri desteklemelidir ZORUNLU.
Elde taşınır cihaz uygulamaları:
- [ 7.6 .2/H-0-1] 1 GiB'den küçük bir uygulama paylaşımlı depolama alanı SAĞLAMAMALIDIR.
- [ 7.7 .1/H] Çevresel modu destekleyen bir USB bağlantı noktası içermelidir.
Elde taşınır cihaz uygulamaları çevre birimi modunu destekleyen bir USB bağlantı noktası içeriyorsa:
- [ 7.7 .1/H-1-1] Android Açık Aksesuar (AOA) API'sini UYGULAMALIDIR.
Elde taşınır cihaz uygulamaları ana bilgisayar modunu destekleyen bir USB bağlantı noktası içeriyorsa:
- [ 7.7 .2/H-1-1] USB ses sınıfını Android SDK belgelerinde belgelendiği şekilde UYGULAMALIDIR.
Elde taşınır cihaz uygulamaları:
- [ 7.8 .1/H-0-1] Bir mikrofon içermelidir ZORUNLU.
- [ 7.8 .2/H-0-1] Bir ses çıkışına sahip olmalı ve
android.hardware.audio.output
olarak bildirilmelidir.
Elde taşınır cihaz uygulamaları, VR modunu desteklemek için tüm performans gereksinimlerini karşılayabiliyorsa ve buna yönelik desteği içeriyorsa:
- [ 7.9 .1/H-1-1]
android.hardware.vr.high_performance
özellik işaretini bildirmesi ZORUNLUDUR. - [ 7.9 .1/H-1-2]
android.app.Activity#setVrModeEnabled
aracılığıyla VR uygulamaları tarafından etkinleştirilebilenandroid.service.vr.VrListenerService
uygulayan bir uygulamayı içermelidir ZORUNLU.
Elde taşınır cihaz uygulamaları, ana bilgisayar modunda bir veya daha fazla USB-C bağlantı noktası/bağlantı noktası içeriyorsa ve (USB ses sınıfı) uyguluyorsa, bölüm 7.7.2'deki gereksinimlere ek olarak:
- [ 7.8 .2.2/H-1-1] HID kodlarının aşağıdaki yazılım eşlemesini sağlamalıdır ZORUNLU:
İşlev | Eşlemeler | Bağlam | Davranış |
---|---|---|---|
A | HID kullanım sayfası : 0x0C HID kullanımı : 0x0CD Çekirdek anahtarı : KEY_PLAYPAUSE Android anahtarı : KEYCODE_MEDIA_PLAY_PAUSE | Medya oynatma | Giriş : Kısa basış Çıkış : Oynat veya duraklat |
Giriş : Uzun basış Çıkış : Sesli komutu başlat Cihaz kilitliyse veya ekranı kapalıysa android.speech.action.VOICE_SEARCH_HANDS_FREE gönderilir . Aksi takdirde android.speech.RecognizerIntent.ACTION_WEB_SEARCH gönderir | |||
Gelen çağrı | Giriş : Kısa basış Çıkış : Aramayı kabul et | ||
Giriş : Uzun basış Çıkış : Aramayı reddet | |||
Devam eden çağrı | Giriş : Kısa basış Çıkış : Aramayı sonlandır | ||
Giriş : Uzun basış Çıkış : Mikrofonun sesini kapatın veya açın | |||
B | HID kullanım sayfası : 0x0C HID kullanımı : 0x0E9 Çekirdek anahtarı : KEY_VOLUMEUP Android anahtarı : VOLUME_UP | Medya oynatma, Devam eden çağrı | Giriş : Kısa veya uzun basma Çıkış : Sistemin veya kulaklığın ses düzeyini artırır |
C | HID kullanım sayfası : 0x0C HID kullanımı : 0x0EA Çekirdek anahtarı : KEY_VOLUMEDOWN Android tuşu : VOLUME_DOWN | Medya oynatma, Devam eden çağrı | Giriş : Kısa veya uzun basma Çıkış : Sistemin veya kulaklığın sesini azaltır |
D | HID kullanım sayfası : 0x0C HID kullanımı : 0x0CF Çekirdek anahtarı : KEY_VOICECOMMAND Android anahtarı : KEYCODE_VOICE_ASSIST | Tüm. Her durumda tetiklenebilir. | Giriş : Kısa veya uzun basma Çıkış : Sesli komutu başlat |
- [ 7.8 .2.2/H-1-2] ACTION_HEADSET_PLUG'ı bir fiş takıldığında tetiklemesi ZORUNLUDUR, ancak bu yalnızca bağlı terminalin tipini tanımlamak için USB ses arayüzleri ve uç noktalar doğru şekilde numaralandırıldıktan sonra gerçekleşir.
USB ses terminali tipleri 0x0302 algılandığında bunlar:
- [ 7.8 .2.2/H-2-1] ACTION_HEADSET_PLUG amacını "mikrofon" ekstrası 0'a ayarlanmış şekilde yayınlaması ZORUNLUDUR.
USB ses terminali tipleri 0x0402 algılandığında bunlar:
- [ 7.8 .2.2/H-3-1] ACTION_HEADSET_PLUG amacını "mikrofon" ekstrası 1'e ayarlanmış şekilde yayınlaması ZORUNLUDUR.
USB çevre birimi bağlıyken API AudioManager.getDevices() çağrıldığında bunlar:
[ 7.8 .2.2/H-4-1] USB ses terminali türü alanı 0x0302 ise AudioDeviceInfo.TYPE_USB_HEADSET türünde bir aygıtın ve isSink() rolünde listelenmesi ZORUNLUDUR.
[ 7.8 .2.2/H-4-2] USB ses terminali türü alanı 0x0402 ise AudioDeviceInfo.TYPE_USB_HEADSET türünde bir aygıtın ve isSink() rolünde listelenmesi ZORUNLUDUR.
[ 7.8 .2.2/H-4-3] USB ses terminali türü alanı 0x0402 ise, AudioDeviceInfo.TYPE_USB_HEADSET türünde bir aygıtın ve isSource() rolünün listelenmesi ZORUNLUDUR.
[ 7.8 .2.2/H-4-4] USB ses terminali tipi alanı 0x603 ise AudioDeviceInfo.TYPE_USB_DEVICE tipinde bir cihazı ve isSink() rolünü listelemesi ZORUNLUDUR.
[ 7.8 .2.2/H-4-5] USB ses terminali türü alanı 0x604 ise AudioDeviceInfo.TYPE_USB_DEVICE türünde bir aygıtın ve isSource() rolünün listelenmesi ZORUNLUDUR.
[ 7.8 .2.2/H-4-6] USB ses terminali türü alanı 0x400 ise AudioDeviceInfo.TYPE_USB_DEVICE türünde bir aygıtın ve isSink() rolünde listelenmesi ZORUNLUDUR.
[ 7.8 .2.2/H-4-7] USB ses terminali tipi alanı 0x400 ise AudioDeviceInfo.TYPE_USB_DEVICE tipinde bir cihazı ve isSource() rolünü listelemesi ZORUNLUDUR.
[ 7.8 .2.2/H-SR-1] USB tanımlayıcılarının numaralandırılmasını gerçekleştirmek, terminal türlerini tanımlamak ve ACTION_HEADSET_PLUG amacını 1000 milisaniyeden daha kısa sürede yayınlamak için bir USB-C ses çevre birimi bağlandığında KESİNLİKLE ÖNERİRİZ.
Elde taşınır cihaz uygulamaları android.hardware.audio.output
ve android.hardware.microphone
olarak bildirirse:
- [5.6(#56_audio-latency)/H-1-1] Desteklenen en az bir yol üzerinde Ortalama Mutlak Sapma 100 ms'den az olacak şekilde, 5 ölçüm boyunca 800 milisaniye veya daha az Ortalama Sürekli Gidiş-Dönüş gecikmesine sahip OLMALIDIR.
Elde taşınır cihaz uygulamaları en az bir dokunsal aktüatör içeriyorsa:
- [ 7.10 /H]* Eksantrik dönen kütle (ERM) dokunsal aktüatörü (vibratör) KULLANMAMALIDIR.
- [ 7.10 /H]* Aktüatörün yerleşimi, cihazın genellikle elle tutulduğu veya dokunulduğu konuma yakın bir yere yerleştirilmelidir GEREKLİ.
- [ 7.10 /H]* Android.view.HapticFeedbackConstants'ta net dokunsal bilgiler için tüm genel sabitleri uygulamalıdır (CLOCK_TICK, CONTEXT_CLICK, KEYBOARD_PRESS, KEYBOARD_RELEASE, KEYBOARD_TAP, LONG_PRESS, TEXT_HANDLE_MOVE, VIRTUAL_KEY, VIRTUAL_KEY_RELEASE, CONFIRM, REJECT) , GESTURE_START ve GESTURE_END).
- [ 7.10 /H]* android.os.VibrationEffect'te net dokunsal bilgiler için tüm genel sabitleri (EFFECT_TICK, EFFECT_CLICK, EFFECT_HEAVY_CLICK ve EFFECT_DOUBLE_CLICK) ve android.os.VibrationEffect.Composition'da zengin dokunsallar için tüm genel sabitleri yani (PRIMITIVE_CLICK ve PRIMITIVE_TICK) UYGULAMALIDIR ).
- [ 7.10 /H]* Bu bağlantılı dokunsal sabit eşlemelerini KULLANMALIDIR.
- [ 7.10 /H]*
createOneShot()
vecreateWaveform()
API'leri için kalite değerlendirmesini takip ETMELİDİR. - [ 7.10 /H]*
android.os.Vibrator.hasAmplitudeControl()
çalıştırarak genlik ölçeklenebilirliğine yönelik yetenekleri doğrulaması GEREKİR.
Doğrusal rezonans aktüatör (LRA), kütlenin istenen hareket yönünde çevrildiği baskın bir rezonans frekansına sahip tek kütleli bir yay sistemidir.
Elde taşınır cihaz uygulamaları en az bir doğrusal rezonans aktüatör içeriyorsa:
- [ 7.10 /H]* Dokunsal aktüatörü dikey yönlendirmenin X ekseninde hareket ettirmesi GEREKİR.
Elde taşınır cihaz uygulamalarında X ekseni doğrusal rezonans aktüatörü (LRA) olan dokunsal bir aktüatör varsa, bunlar:
- [ 7.10 /H]* X ekseni LRA'nın rezonans frekansı 200 Hz'nin altında OLMALIDIR.
Elde taşınan cihaz uygulamaları dokunsal sabit haritalamayı takip ediyorsa:
- [7.10/H]* Android.os.Vibrator.areAllEffectsSupported() ve android.os.Vibrator.arePrimitvesSupported() API'lerini çalıştırarak uygulama durumunu doğrulaması GEREKİR.
- [ 7.10 /H]* Dokunsal sabitler için bir kalite değerlendirmesi YAPMALIDIR.
- [7.10/H]* Burada açıklandığı gibi arıza riskini azaltmak için geri dönüş desteği SAĞLAMALIDIR.
2.2.2. Multimedya
Elde taşınan cihaz uygulamalarının aşağıdaki ses kodlama ve kod çözme formatlarını desteklemesi ve bunları üçüncü taraf uygulamaların kullanımına sunması ZORUNLUDUR:
- [ 5.1 /H-0-1] AMR-NB
- [ 5.1 /H-0-2] AMR-WB
- [ 5.1 /H-0-3] MPEG-4 AAC Profili (AAC LC)
- [ 5.1 /H-0-4] MPEG-4 HE AAC Profili (AAC+)
- [ 5.1 /H-0-5] AAC ELD (geliştirilmiş düşük gecikmeli AAC)
Elde taşınır cihaz uygulamalarının aşağıdaki video kodlama formatlarını desteklemesi ve bunları üçüncü taraf uygulamaların kullanımına sunması ZORUNLUDUR:
Elde taşınır cihaz uygulamalarının aşağıdaki video kod çözme formatlarını desteklemesi ve bunları üçüncü taraf uygulamaların kullanımına sunması ZORUNLUDUR:
- [ 5.3 /H-0-1] H.264 AVC
- [ 5.3 /H-0-2] H.265 HEVC
- [ 5.3 /H-0-3] MPEG-4 SP
- [ 5.3 /H-0-4] VP8
- [ 5.3 /H-0-5] VP9
2.2.3. Yazılım
Elde taşınır cihaz uygulamaları:
- [ 3.2.3.1 /H-0-1]
ACTION_GET_CONTENT
,ACTION_OPEN_DOCUMENT
,ACTION_OPEN_DOCUMENT_TREE
veACTION_CREATE_DOCUMENT
amaçlarını SDK belgelerinde açıklandığı şekilde işleyen ve kullanıcıyaDocumentsProvider
API'sini kullanarak belge sağlayıcı verilerine erişme olanağı sağlayan bir uygulamaya sahip OLMALIDIR. - [ 3.2.3.1 /H-0-2]* Burada listelenen aşağıdaki uygulama amaçları tarafından tanımlanan tüm genel amaç filtre modelleri için bir veya daha fazla uygulamayı veya hizmet bileşenini bir amaç işleyiciyle önceden yüklemesi ZORUNLUDUR.
- [ 3.2.3.1 /H-SR-1] Bir e-posta göndermeye yönelik ACTION_SENDTO veya ACTION_SEND veya ACTION_SEND_MULTIPLE amaçlarını işleyebilecek bir e-posta uygulamasını önceden yüklemeniz KESİNLİKLE ÖNERİR.
- [ 3.4 .1/H-0-1]
android.webkit.Webview
API'sinin eksiksiz bir uygulamasını SAĞLAMALIDIR. - [ 3.4 .2/H-0-1] Genel kullanıcı web taraması için bağımsız bir Tarayıcı uygulaması içermelidir ZORUNLU.
- [ 3.8 .1/H-SR-1] Kısayolların, widget'ların ve widgetFeatures'ın uygulama içi sabitlenmesini destekleyen bir varsayılan başlatıcının uygulanması KESİNLİKLE TAVSİYE EDİLİR.
- [ 3.8 .1/H-SR-2] ShortcutManager API aracılığıyla üçüncü taraf uygulamalar tarafından sağlanan ek kısayollara hızlı erişim sağlayan bir varsayılan başlatıcının uygulanması KESİNLİKLE ÖNERİLİR.
- [ 3.8 .1/H-SR-3] Uygulama simgeleri için rozetleri gösteren bir varsayılan başlatıcı uygulaması içermesi KESİNLİKLE TAVSİYE EDİLİR.
- [ 3.8 .2/H-SR-1] Üçüncü taraf uygulama widget'larını desteklemeleri KESİNLİKLE TAVSİYE EDİLİR.
- [ 3.8 .3/H-0-1] Üçüncü taraf uygulamaların,
Notification
veNotificationManager
API sınıfları aracılığıyla kullanıcıları önemli olaylar hakkında bilgilendirmesine izin vermesi ZORUNLUDUR. - [ 3.8 .3/H-0-2] Zengin bildirimleri desteklemelidir ZORUNLU.
- [ 3.8 .3/H-0-3] Dikkat bildirimlerini desteklemelidir ZORUNLU.
- [ 3.8 .3/H-0-4] Kullanıcının, uygulandığı şekliyle eylem düğmeleri veya kontrol paneli gibi kullanıcının sağladığı olanaklar aracılığıyla bildirimleri doğrudan kontrol etme (örneğin yanıtlama, erteleme, kapatma, engelleme) olanağı sağlayan bir bildirim gölgesi içermesi ZORUNLUDUR AOSP'de.
- [ 3.8 .3/H-0-5]
RemoteInput.Builder setChoices()
aracılığıyla sağlanan seçenekleri bildirim gölgesinde GÖRÜNTÜLEMELİDİR. - [ 3.8 .3/H-SR-1]
RemoteInput.Builder setChoices()
yoluyla sağlanan ilk seçeneği ek kullanıcı etkileşimi olmadan bildirim gölgesinde görüntülemeniz KESİNLİKLE TAVSİYE EDİLİR. - [ 3.8 .3/H-SR-2] Kullanıcı bildirim gölgesindeki tüm bildirimleri genişlettiğinde,
RemoteInput.Builder setChoices()
aracılığıyla sağlanan tüm seçenekleri bildirim gölgesinde görüntülemeniz KESİNLİKLE TAVSİYE EDİLİR. - [ 3.8 .3.1/H-SR-1]
Notification.Action.Builder.setContextual
,Notification.Remoteinput.Builder.setChoices
tarafından görüntülenen yanıtlarla aynı doğrultudatrue
olarak ayarlandığı eylemleri görüntülemek KESİNLİKLE ÖNERİR. - [ 3.8 .4/H-SR-1] Destek eylemini gerçekleştirecek bir asistanın cihaza uygulanması KESİNLİKLE TAVSİYE EDİLİR.
Elde taşınır cihaz uygulamaları Yardım eylemini destekliyorsa:
- [ 3.8 .4/H-SR-2] Bölüm 7.2.3'te açıklandığı gibi destek uygulamasını başlatmak için belirlenen etkileşim olarak
HOME
tuşuna uzun basılması KESİNLİKLE TAVSİYE EDİLİR. Kullanıcının seçtiği yardım uygulamasını, başka bir deyişleVoiceInteractionService
uygulayan uygulamayı veyaACTION_ASSIST
amacını işleyen bir etkinliği başlatması GEREKİR.
Elde taşınır cihaz uygulamaları conversation notifications
destekliyorsa ve bunları uyarı ve sessiz konuşma dışı bildirimlerden ayrı bir bölümde gruplandırıyorsa:
- [ 3.8 .4/H-1-1]* Devam eden ön plan hizmet bildirimleri ve önem:yüksek bildirimler hariç olmak üzere, konuşma bildirimlerini konuşma dışı bildirimlerden önce GÖSTERMELİDİR.
Android Handheld cihaz uygulamaları kilit ekranını destekliyorsa:
- [ 3.8 .10/H-1-1] Medya Bildirim Şablonu da dahil olmak üzere Kilit ekranı Bildirimlerini görüntülemelidir ZORUNLU.
Elde taşınır cihaz uygulamaları güvenli bir kilit ekranını destekliyorsa:
- [ 3.9 /H-1-1] Android SDK belgelerinde tanımlanan cihaz yönetimi politikalarının tamamını UYGULAMALIDIR.
Elde taşınır cihaz uygulamaları ControlsProviderService
ve Control
API'leri için destek içeriyorsa ve üçüncü taraf uygulamaların cihaz kontrolleri yayınlamasına izin veriyorsa, bu durumda:
- [ 3.8 .16/H-1-1]
android.software.controls
özellik işaretini bildirmeli ve bunutrue
olarak ayarlamalıdır ZORUNLU. - [ 3.8 .16/H-1-2]
ControlsProviderService
veControl
API'leri aracılığıyla üçüncü taraf uygulamalar tarafından kaydedilen kontrollerden kullanıcının favori cihaz kontrollerini ekleme, düzenleme, seçme ve çalıştırma becerisine sahip bir kullanıcıya olanak sağlamalıdır ZORUNLU . - [ 3.8 .16/H-1-3] Varsayılan Başlatıcıdan üç etkileşim içinde bu kullanıcıya erişim sağlamalıdır ZORUNLU.
- [ 3.8 .16/H-1-4]
ControlsProviderService
API aracılığıyla kontroller sağlayan her üçüncü taraf uygulamasının adını ve simgesini ve ayrıcaControl
API'leri tarafından sağlanan belirli alanları bu kullanıcı olanağında doğru bir şekilde VERMELİDİR.
Bunun tersine, El tipi cihaz uygulamaları bu tür kontrolleri uygulamıyorsa:
- [ 3.8 .16/H-2-1]
ControlsProviderService
veControl
API'leri içinnull
raporlaması ZORUNLUDUR. - [ 3.8 .16/H-2-2]
android.software.controls
özellik işaretini bildirmeli ve bunufalse
olarak ayarlamalıdır ZORUNLU.
Elde taşınır cihaz uygulamaları:
- [ 3.10 /H-0-1] Üçüncü taraf erişilebilirlik hizmetlerini desteklemelidir ZORUNLU.
- [ 3.10 /H-SR-1] Anahtar Erişimi ve TalkBack (önceden yüklenmiş Metin-konuşma motoru tarafından desteklenen diller için) erişilebilirlik hizmetleriyle karşılaştırılabilir veya bu işlevleri aşan erişilebilirlik hizmetlerinin cihaza önceden yüklenmesi KESİNLİKLE ÖNERİR-1 talkback açık kaynak projesinde .
- [ 3.11 /H-0-1] Üçüncü taraf TTS motorlarının kurulumunu desteklemelidir ZORUNLU.
- [ 3.11 /H-SR-1] Cihazda mevcut dilleri destekleyen bir TTS motorunun dahil edilmesi KESİNLİKLE TAVSİYE EDİLİR.
- [ 3.13 /H-SR-1] Hızlı Ayarlar Kullanıcı Arayüzü bileşeninin dahil edilmesi KESİNLİKLE TAVSİYE EDİLİR.
Android el tipi cihaz uygulamaları FEATURE_BLUETOOTH
veya FEATURE_WIFI
desteğini beyan ederse:
- [ 3.16 /H-1-1] Yardımcı cihaz eşleştirme özelliğini desteklemesi ZORUNLUDUR.
Gezinme işlevi ekranda, harekete dayalı bir eylem olarak sağlanıyorsa:
- [ 7.2 .3/H] Giriş işlevi için hareket tanıma bölgesinin yüksekliği ekranın alt kısmından 32 dp'den yüksek OLMAMALIDIR.
Elde taşınır cihaz uygulamaları ekranın sol ve sağ kenarlarında herhangi bir yerden hareket olarak gezinme işlevi sağlıyorsa:
- [ 7.2 .3/H-0-1] Gezinme fonksiyonunun hareket alanının her iki tarafta genişliği 40 dp'den az OLMALIDIR. Hareket alanının varsayılan olarak genişliği 24 dp OLMALIDIR.
Elde taşınır cihaz uygulamaları güvenli bir kilit ekranını destekliyorsa ve çekirdek ve kullanıcı alanı için 2 GB veya daha fazla kullanılabilir belleğe sahipse, bunlar:
- [3.9/H-1-2]
android.software.managed_users
özellik işareti aracılığıyla yönetilen profillerin desteğini beyan etmesi GEREKİR.
Android el tipi cihaz uygulamaları kamera desteğini android.hardware.camera.any
aracılığıyla beyan ederse:
- [ 7.5 .4/H-1-1]
android.media.action.STILL_IMAGE_CAMERA
veandroid.media.action.STILL_IMAGE_CAMERA_SECURE
amacını dikkate almalı ve kamerayı SDK'da açıklandığı gibi hareketsiz görüntü modunda başlatmalıdır. - [ 7.5 .4/H-1-2] SDK'da açıklandığı gibi kamerayı video modunda başlatmak için
android.media.action.VIDEO_CAMERA
amacına uyması ZORUNLUDUR.
2.2.4. Performans ve Güç
- [ 8.1 /H-0-1] Tutarlı kare gecikmesi . Tutarsız kare gecikmesi veya karelerin oluşturulmasındaki gecikme, saniyede 5 kareden daha sık OLMAMALIDIR ve saniyede 1 karenin altında OLMALIDIR.
- [ 8.1 /H-0-2] Kullanıcı arayüzü gecikmesi . Cihaz uygulamaları, Android Uyumluluk Test Paketi (CTS) tarafından tanımlanan 10 bin liste girişinin listesini 36 saniyeden kısa sürede kaydırarak düşük gecikmeli kullanıcı deneyimi SAĞLAMALIDIR.
- [ 8.1 /H-0-3] Görev değiştirme . Birden fazla uygulama başlatıldığında, halihazırda çalışmakta olan bir uygulamanın başlatıldıktan sonra yeniden başlatılması 1 saniyeden kısa sürmesi GEREKİR.
Elde taşınır cihaz uygulamaları:
- [ 8.2 /H-0-1] En az 5 MB/sn sıralı yazma performansı SAĞLAMALIDIR.
- [ 8.2 /H-0-2] En az 0,5 MB/sn'lik rastgele yazma performansı SAĞLAMALIDIR.
- [ 8.2 /H-0-3] En az 15 MB/sn sıralı okuma performansı ZORUNLUDUR.
- [ 8.2 /H-0-4] En az 3,5 MB/sn'lik rastgele okuma performansı ZORUNLUDUR.
Elde taşınır cihaz uygulamaları, AOSP'de bulunan cihaz güç yönetimini iyileştirmeye yönelik özellikler içeriyorsa veya AOSP'de bulunan özellikleri genişletiyorsa:
- [ 8.3 /H-1-1] Kullanıcıya pil tasarrufu özelliğini etkinleştirme ve devre dışı bırakma olanağı sağlamalıdır ZORUNLU.
- [ 8.3 /H-1-2] Uygulama Bekleme ve Doze güç tasarrufu modlarından muaf tutulan tüm uygulamaları görüntülemek için kullanıcıya olanak sağlamalıdır ZORUNLU.
Elde taşınır cihaz uygulamaları:
- [ 8.4 /H-0-1] Android Açık Kaynak Projesi sitesinde belgelendiği gibi, her donanım bileşeni için geçerli tüketim değerini ve bileşenlerin zaman içinde neden olduğu yaklaşık pil tüketimini tanımlayan bileşen başına bir güç profili SAĞLAMALIDIR.
- [ 8.4 /H-0-2] Tüm güç tüketimi değerleri miliamper saat (mAh) cinsinden bildirilmelidir ZORUNLU.
- [ 8.4 /H-0-3] Her işlemin UID'sine göre CPU güç tüketimini bildirmesi ZORUNLUDUR. Android Açık Kaynak Projesi, gereksinimi
uid_cputime
çekirdek modülü uygulaması aracılığıyla karşılar. - [ 8.4 /H-0-4] Bu güç kullanımını, uygulama geliştiricisinin
adb shell dumpsys batterystats
kabuk komutu aracılığıyla kullanılabilir hale getirmesi GEREKİR. - [ 8.4 /H] Donanım bileşeni güç kullanımını bir uygulamaya ilişkilendiremiyorsanız, donanım bileşeninin kendisine atfedilmesi GEREKİR.
Elde taşınır cihaz uygulamaları bir ekran veya video çıkışı içeriyorsa:
- [ 8.4 /H-1-1]
android.intent.action.POWER_USAGE_SUMMARY
amacını dikkate almalı ve bu güç kullanımını gösteren bir ayarlar menüsünü görüntülemelidir ZORUNLU.
2.2.5. Güvenlik Modeli
Elde taşınır cihaz uygulamaları:
- [ 9.1 /H-0-1] Üçüncü taraf uygulamaların
android.permission.PACKAGE_USAGE_STATS
izni aracılığıyla kullanım istatistiklerine erişmesine izin vermesi ZORUNLU veandroid.settings.ACTION_USAGE_ACCESS_SETTINGS
yanıt olarak bu tür uygulamalara erişim izni vermek veya erişimi iptal etmek için kullanıcı tarafından erişilebilen bir mekanizma sağlamak ZORUNLUDURandroid.settings.ACTION_USAGE_ACCESS_SETTINGS
amaç.
Elde taşınır cihaz uygulamaları:
- [ 9.11 /H-0-2] Anahtar deposu uygulamasının yalıtılmış bir yürütme ortamıyla YEDEKLENMESİ ZORUNLUDUR.
- [ 9.11 /H-0-3] Android Anahtar Deposu sisteminin desteklenen algoritmalarını güvenli bir alanda düzgün bir şekilde desteklemek için RSA, AES, ECDSA ve HMAC şifreleme algoritmalarının uygulamalarına ve MD5, SHA1 ve SHA-2 ailesi karma işlevlerine sahip OLMALIDIR çekirdek ve üzeri üzerinde çalışan koddan izole edilmiştir. Güvenli izolasyon, çekirdek veya kullanıcı alanı kodunun, DMA dahil, izole edilmiş ortamın dahili durumuna erişebileceği tüm potansiyel mekanizmaları ENGELLEMELİDİR. Yukarı akışlı Android Açık Kaynak Projesi (AOSP), Trusty uygulamasını kullanarak bu gereksinimi karşılar, ancak başka bir ARM TrustZone tabanlı çözüm veya uygun bir hipervizör tabanlı izolasyonun üçüncü taraflarca gözden geçirilmiş güvenli uygulaması alternatif seçeneklerdir.
- [ 9.11 /H-0-4] Kilit ekranı kimlik doğrulamasını yalıtılmış yürütme ortamında gerçekleştirmeli ve yalnızca başarılı olduğunda kimlik doğrulamaya bağlı anahtarların kullanılmasına izin vermelidir. Kilit ekranı kimlik bilgileri, yalnızca yalıtılmış yürütme ortamının kilit ekranı kimlik doğrulamasını gerçekleştirmesine izin verecek şekilde saklanmalıdır *ZORUNLU*. Yukarı akışlı Android Açık Kaynak Projesi, bu gereksinimi karşılamak için kullanılabilecek Gatekeeper Donanım Soyutlama Katmanı (HAL) ve Trusty'yi sağlar.
- [ 9.11 /H-0-5] Onay imzalama anahtarının güvenli donanım tarafından korunduğu ve imzalamanın güvenli donanımda gerçekleştirildiği anahtar doğrulamayı desteklemelidir ZORUNLU. Anahtarların cihaz tanımlayıcıları olarak kullanılmasını önlemek için, doğrulama imzalama anahtarlarının yeterli sayıda cihaz arasında paylaşılması ZORUNLUDUR. Bu gereksinimi karşılamanın bir yolu, belirli bir SKU'dan en az 100.000 birim üretilmediği sürece aynı doğrulama anahtarını paylaşmaktır. Bir SKU'nun 100.000 biriminden fazla üretilmesi durumunda her 100.000 birim için farklı bir anahtar KULLANILABİLİR.
- [9/H-0-1] 'android.hardware.security.model.uyumlu' özelliğinin bildirilmesi ZORUNLUDUR.
Bir cihaz uygulaması daha önceki bir Android sürümünde zaten başlatılmışsa, bu tür bir cihazın, yalıtılmış bir yürütme ortamı tarafından desteklenen bir anahtar deposuna sahip olma ve android.hardware.fingerprint
doğrulamayı destekleme gerekliliğinden muaf tutulacağını unutmayın; yalıtılmış bir yürütme ortamı tarafından desteklenen bir anahtar deposu gerektirir.
Taşınabilir cihaz uygulamaları güvenli bir kilit ekranını desteklediğinde:
- [ 9.11 /H-1-1] Kullanıcının en kısa uyku zaman aşımını, yani kilit açık durumdan kilitli duruma geçiş süresini 15 saniye veya daha kısa olarak seçmesine izin vermelidir ZORUNLU.
- [ 9.11 /H-1-2] Kullanıcıya bildirimleri gizleme ve 9.11.1 Güvenli Kilit Ekranı'nda açıklanan birincil kimlik doğrulama dışında tüm kimlik doğrulama biçimlerini devre dışı bırakma olanağı sağlamalıdır ZORUNLU. AOSP, kilitleme modu olarak gereksinimi karşılar.
Elde taşınır cihaz uygulamaları birden fazla kullanıcı içeriyorsa ve android.hardware.telephony
özellik işaretini bildirmiyorsa, bunlar:
- [ 9.5 /H-2-1] Cihaz sahiplerinin cihazdaki ek kullanıcıları ve onların yeteneklerini yönetmesine olanak tanıyan bir özellik olan kısıtlı profilleri desteklemesi ZORUNLUDUR. Kısıtlanmış profiller sayesinde cihaz sahipleri, ek kullanıcıların çalışabileceği ayrı ortamları hızlı bir şekilde oluşturabilir ve bu ortamlarda bulunan uygulamalardaki daha ayrıntılı kısıtlamaları yönetebilir.
Elde taşınır cihaz uygulamaları birden fazla kullanıcı içeriyorsa ve android.hardware.telephony
özellik işaretini bildiriyorsa, bunlar:
- [ 9.5 /H-3-1] Kısıtlanmış profilleri DESTEKLEMEMELİDİR ancak diğer kullanıcıların sesli çağrılara ve SMS'lere erişimini etkinleştirmek/devre dışı bırakmak için AOSP kontrol uygulamasıyla uyumlu OLMALIDIR.
Android, Sistem API'si VoiceInteractionService aracılığıyla, mikrofon erişim göstergesi olmadan her zaman açık, güvenli özel kelime algılamaya yönelik bir mekanizmayı destekler
Elde taşınır cihaz uygulamaları Sistem API'si HotwordDetectionService
veya mikrofon erişimi göstergesi olmadan özel kelime algılamaya yönelik başka bir mekanizmayı destekliyorsa, bunlar:
- [9.8/H-1-1] Özel kelime algılama hizmetinin yalnızca Sisteme veya ContentCaptureService'e veri aktarabildiğinden emin olunmalıdır ZORUNLU
- [9.8/H-1-2] Özel kelime algılama hizmetinin yalnızca mikrofon ses verilerini veya ondan türetilen verileri
HotwordDetectionService
API aracılığıyla sistem sunucusuna veyaContentCaptureManager
API aracılığıylaContentCaptureService
iletebildiğinden emin olunmalıdır. - [9.8/H-1-3] Özel kelime algılama hizmetine donanım tarafından tetiklenen bireysel bir istek için 30 saniyeden uzun mikrofon sesi SAĞLAMAMALIDIR.
- [9.8/H-1-4] Özel kelime algılama hizmetine bireysel bir istek için 8 saniyeden eski ara belleğe alınmış mikrofon sesi SAĞLAMAMALIDIR.
- [9.8/H-1-5] 30 saniyeden eski ara belleğe alınmış mikrofon sesini sesli etkileşim hizmetine veya benzer bir kuruluşa SAĞLAMAMALIDIR.
- [9.8/H-1-6] Her başarılı özel kelime sonucunda özel kelime algılama hizmetinden 100 bayttan fazla verinin iletilmesine izin VERMEMELİDİR.
- [9.8/H-1-7] Her negatif özel kelime sonucunda özel kelime algılama hizmetinden 5 bitten fazla verinin iletilmesine izin VERMEMELİDİR.
- [9.8/H-1-8] Yalnızca sistem sunucusundan gelen bir özel kelime doğrulama isteği üzerine özel kelime algılama hizmetinden veri aktarımına izin verilmesi ZORUNLUDUR.
- [9.8/H-1-9] Kullanıcı tarafından yüklenebilen bir uygulamanın özel kelime algılama hizmeti sağlamasına izin VERMEMELİDİR.
- [9.8/H-1-10] Özel kelime algılama hizmetinin mikrofon kullanımına ilişkin niceliksel verileri kullanıcı arayüzünde ortaya ÇIKMAMALIDIR.
- [9.8/H-1-11] Güvenlik araştırmacılarının denetlenebilmesine olanak sağlamak amacıyla özel kelime algılama hizmetinden gelen her iletimde yer alan bayt sayısını kaydetmesi GEREKİR.
- [9.8/H-1-12] Güvenlik araştırmacılarına incelenebilirlik sağlamak için özel kelime algılama hizmetinden gelen her iletimin ham içeriğini günlüğe kaydeden bir hata ayıklama modunu desteklemelidir ZORUNLU.
- [9.8/H-1-13] Özel kelime algılama hizmetini barındıran işlemi en az saatte bir veya her 30 donanım tetikleme olayında (hangisi önce gerçekleşirse) yeniden başlatması GEREKİR.
- [9.8/H-1-14] Başarılı bir özel kelime sonucu sesli etkileşim hizmetine veya benzer bir kuruluşa iletildiğinde, bölüm 9.8.2'de açıklandığı gibi mikrofon göstergesini görüntülemesi ZORUNLUDUR.
- [9.8/H-SR-1] Bir uygulamayı özel kelime algılama hizmetinin sağlayıcısı olarak ayarlamadan önce kullanıcıları bilgilendirmeniz KESİNLİKLE TAVSİYE EDİLİR.
- [9.8/H-SR-2] Yapılandırılmamış verilerin özel kelime algılama hizmetinden aktarılmasına izin verilmemesi KESİNLİKLE ÖNERİLMEKTEDİR.
Cihaz uygulamaları, Sistem API'si HotwordDetectionService
kullanan bir uygulamayı veya mikrofon kullanımı göstergesi olmadan özel kelime algılamaya yönelik benzer bir mekanizmayı içeriyorsa, uygulama:
- [9.8/H-2-1] Desteklenen her özel kelime öbeği için kullanıcıya açık bildirimde bulunulması ZORUNLUDUR.
- [9.8/H-2-2] Özel kelime algılama hizmeti aracılığıyla ham ses verilerini veya bundan türetilen verileri KORUMAMALIDIR.
- [9.8/H-2-3] Özel kelime algılama hizmetinden, ses verilerini, sesi yeniden oluşturmak için kullanılabilecek verileri (tamamen veya kısmen) veya özel kelimenin kendisiyle ilgisi olmayan ses içeriklerini (
ContentCaptureService
dışında) İLETMEMELİDİR.
Elde taşınır cihaz uygulamaları android.hardware.microphone
olarak bildirirse:
- [ 9.8.2 /H-4-1] Bir uygulama mikrofondan ses verilerine erişirken mikrofon göstergesinin görüntülenmesi ZORUNLUDUR, ancak mikrofona yalnızca
HotwordDetectionService
,SOURCE_HOTWORD
,ContentCaptureService
veya bölümde belirtilen rollere sahip uygulamalar tarafından erişildiğinde bu görüntülenmemelidir. CDD tanımlayıcılı [C-4-X] 9.1 . . - [ 9.8.2 /H-4-2]
PermissionManager.getIndicatorAppOpUsageData()
işlevinden döndürülen mikrofon kullanan Son ve Aktif uygulamaların listesini, bunlarla ilişkili tüm atıf mesajlarıyla birlikte GÖRÜNTÜLEMELİDİR. - [ 9.8.2 /H-4-3] Görünür kullanıcı arayüzlerine veya doğrudan kullanıcı etkileşimine sahip sistem uygulamaları için mikrofon göstergesini GİZLEMEMELİDİR.
- [ 9.8.2 /H-4-4]
PermissionManager.getIndicatorAppOpUsageData()
işlevinden döndürülen mikrofonu kullanan Son ve Aktif uygulamaların listesini, bunlarla ilişkili tüm atıf mesajlarıyla birlikte GÖRÜNTÜLEMELİDİR.
Elde taşınır cihaz uygulamaları android.hardware.camera.any
olarak bildirirse:
- [ 9.8.2 /H-5-1] Bir uygulama canlı kamera verilerine eriştiğinde kamera göstergesinin görüntülenmesi ZORUNLUDUR, ancak kameraya yalnızca bölüm 9.1'de CDD tanımlayıcıyla belirtilen rolleri taşıyan uygulamalar tarafından erişildiğinde bu görüntülenmemelidir. [C-4-X].
- [ 9.8.2 /H-5-2]
PermissionManager.getIndicatorAppOpUsageData()
öğesinden döndürülen kamerayı kullanan Son ve Etkin uygulamaları, bunlarla ilişkili tüm atıf mesajlarıyla birlikte görüntülemesi ZORUNLUdur. - [ 9.8.2 /H-5-3] Görünür kullanıcı arayüzlerine veya doğrudan kullanıcı etkileşimine sahip sistem uygulamaları için kamera göstergesini GİZLEMEMELİDİR.
2.2.6. Geliştirici Araçları ve Seçenekleri Uyumluluğu
Elde taşınır cihaz uygulamaları (* Tablet için geçerli değildir):
- [ 6.1 /H-0-1]*
cmd testharness
kabuk komutunu desteklemesi ZORUNLUDUR.
Elde taşınır cihaz uygulamaları (* Tablet için geçerli değildir):
- mükemmel
- [ 6.1 /H-0-2]* Kabuk kullanıcısına, perfetto belgelerine uygun olan cmdline'ın bir
/system/bin/perfetto
ikili dosyasını sunması GEREKİR. - [ 6.1 /H-0-3]* Perfetto ikilisinin , perfetto belgelerinde tanımlanan şemaya uygun bir protobuf yapılandırmasını giriş olarak kabul etmesi ZORUNLUDUR.
- [ 6.1 /H-0-4]* Perfetto ikilisinin perfetto belgelerinde tanımlanan şemaya uygun bir protobuf izini çıktı olarak yazması ZORUNLUDUR.
- [ 6.1 /H-0-5]* perfetto ikili dosyası aracılığıyla en azından perfetto belgelerinde açıklanan veri kaynaklarını SAĞLAMALIDIR.
- [ 6.1 /H-0-6]* Perfetto izlenen arka plan programının varsayılan olarak etkinleştirilmesi ZORUNLUDUR (sistem özelliği
persist.traced.enable
).
- [ 6.1 /H-0-2]* Kabuk kullanıcısına, perfetto belgelerine uygun olan cmdline'ın bir
2.2.7. Elde Taşınabilir Medya Performans Sınıfı
Medya performans sınıfının tanımı için Bölüm 7.11'e bakınız.
2.2.7.1. Medya
Elde taşınır cihaz uygulamaları android.os.Build.VERSION_CODES.R
için android.os.Build.VERSION.MEDIA_PERFORMANCE_CLASS
değerini döndürürse, o zaman:
- Android 11 CDD bölüm 2.2.7.1'de listelenen medya gereksinimlerini karşılaması ZORUNLUDUR
Elde taşınır cihaz uygulamaları android.os.Build.VERSION_CODES.S
için android.os.Build.VERSION.MEDIA_PERFORMANCE_CLASS
değerini döndürürse, bunlar:
- [5.1/H-1-1]
CodecCapabilities.getMaxSupportedInstances()
veVideoCapabilities.getSupportedPerformancePoints()
yöntemleri aracılığıyla herhangi bir codec kombinasyonunda eşzamanlı olarak çalıştırılabilecek maksimum donanım video kod çözücü oturumu sayısını duyurması ZORUNLUDUR. - [5.1/H-1-2] 720p çözünürlükte @30 fps'de eşzamanlı olarak çalışan herhangi bir codec kombinasyonunda 6 donanım video kod çözücü oturumu örneğini (AVC, HEVC, VP9* veya üstü) desteklemelidir ZORUNLU. *VP9 codec bileşeni mevcutsa yalnızca 2 örnek gereklidir.
- [5.1/H-1-3]
CodecCapabilities.getMaxSupportedInstances()
veVideoCapabilities.getSupportedPerformancePoints()
yöntemleri aracılığıyla herhangi bir codec kombinasyonunda eş zamanlı olarak çalıştırılabilecek maksimum donanım video kodlayıcı oturumu sayısını duyurması GEREKLİdir. - [5.1/H-1-4] 720p çözünürlükte @30 fps'de eşzamanlı olarak çalışan herhangi bir codec kombinasyonunda donanım video kodlayıcı oturumlarının 6 örneğini (AVC, HEVC, VP9* veya üstü) desteklemelidir ZORUNLU. *VP9 codec bileşeni mevcutsa yalnızca 2 örnek gereklidir.
- [5.1/H-1-5]
CodecCapabilities.getMaxSupportedInstances()
veVideoCapabilities.getSupportedPerformancePoints()
yöntemleri aracılığıyla herhangi bir codec bileşeni kombinasyonunda eşzamanlı olarak çalıştırılabilecek maksimum sayıda donanım video kodlayıcı ve kod çözücü oturumunun duyurulması GEREKİR. - [5.1/H-1-6] 720p@30fps çözünürlükte eş zamanlı çalışan herhangi bir codec kombinasyonunda donanım video kod çözücü ve donanım video kodlayıcı oturumlarının (AVC, HEVC, VP9* veya üstü) 6 örneğini desteklemesi ZORUNLUDUR. *VP9 codec bileşeni mevcutsa yalnızca 2 örnek gereklidir.
- [5.1/H-1-7] Yük altındayken tüm donanım video kodlayıcıları (Dolby Vision codec bileşeni dışında) için 1080p veya daha küçük bir video kodlama oturumu için codec başlatma gecikmesi 50 ms veya daha az OLMALIDIR. Buraya yükleme, 1080p ses-video kaydı başlatmayla birlikte donanım video codec'lerini kullanan eşzamanlı 1080p'den 720p'ye yalnızca video kod dönüştürme oturumu olarak tanımlanır.
- [5.1/H-1-8] Yük altındayken tüm ses kodlayıcılar için 128 kbps veya daha düşük bit hızlı ses kodlama oturumu için 40 ms veya daha az codec başlatma gecikmesine sahip olması GEREKİR. Buraya yükleme, 1080p ses-video kaydı başlatmayla birlikte donanım video codec'lerini kullanan eşzamanlı 1080p'den 720p'ye yalnızca video kod dönüştürme oturumu olarak tanımlanır.
- [5.3/H-1-1] Yük altında 1080p 60 fps video oturumu için 10 saniyede 2 kareden fazla (yani yüzde 0,333'ten az kare düşüşü) DÜŞMEMELİDİR. Yük, donanım video codec'lerinin yanı sıra 128 kbps AAC ses oynatımı kullanılarak eşzamanlı 1080p'den 720p'ye yalnızca video kod dönüştürme oturumu olarak tanımlanır.
- [5.3/H-1-2] Yük altında 60 fps video oturumunda video çözünürlüğü değişikliği sırasında 10 saniyede 2 kareden fazla DÜŞMEMELİDİR. Yük, donanım video codec'lerinin yanı sıra 128 kbps AAC ses oynatımı kullanılarak eşzamanlı 1080p'den 720p'ye yalnızca video kod dönüştürme oturumu olarak tanımlanır.
- [5.6/H-1-1] OboeTester hafifçe vurarak tonlama testi veya CTS Verifier dokunarak tonlama testi kullanıldığında, dokunmadan tona geçme gecikmesi 100 milisaniyeden daha az OLMALIDIR.
2.2.7.2. Kamera
Elde taşınır cihaz uygulamaları android.os.Build.VERSION_CODES.R
için android.os.Build.VERSION.MEDIA_PERFORMANCE_CLASS
değerini döndürürse, o zaman:
- Android 11 CDD bölüm 2.2.7.2'de listelenen kamera gereksinimlerinin karşılanması ZORUNLUDUR
Elde taşınır cihaz uygulamaları android.os.Build.VERSION_CODES.S
için android.os.Build.VERSION.MEDIA_PERFORMANCE_CLASS
değerini döndürürse, bunlar:
- [7.5/H-1-1] 4k@30 fps'de video çekimini destekleyen, en az 12 megapiksel çözünürlüğe sahip, arkaya bakan bir birincil kamera OLMALIDIR. Birincil arkaya bakan kamera, en düşük kamera kimliğine sahip arkaya bakan kameradır.
- [7.5/H-1-2] En az 5 megapiksel çözünürlüğe sahip ve 1080p@30fps hızında video çekimini destekleyen bir birincil ön kameraya sahip olmalıdır. Birincil ön kamera, en düşük kamera kimliğine sahip ön kameradır.
- [7.5/H-1-3]
android.info.supportedHardwareLevel
özelliğini her iki birincil kamera içinFULL
veya daha iyi olarak desteklemelidir ZORUNLU. - [7.5/H-1-4] her iki birincil kamera için
CameraMetadata.SENSOR_INFO_TIMESTAMP_SOURCE_REALTIME
desteklemelidir ZORUNLU. - [7.5/H-1-5] Her iki birincil kamera için ITS aydınlatma koşulları (3000K) altında CTS kamera Performans Testi ile ölçülen 1080p çözünürlük için kamera2 JPEG yakalama gecikmesi < 1000 ms olmalıdır.
- [7.5/H-1-6] Her iki birincil kamera için ITS aydınlatma koşulları (3000K) altında CTS kamera Performans Testi ile ölçülen kamera2 başlatma gecikmesi (kamerayı ilk önizleme karesine açın) < 600 ms OLMALIDIR.
- [7.5/H-1-8] Birincil arka kamera için
CameraMetadata.REQUEST_AVAILABLE_CAPABILITIES_RAW
veandroid.graphics.ImageFormat.RAW_SENSOR
desteklemesi ZORUNLUDUR.
2.2.7.3. Donanım
Elde taşınır cihaz uygulamaları android.os.Build.VERSION_CODES.R
için android.os.Build.VERSION.MEDIA_PERFORMANCE_CLASS
değerini döndürürse, o zaman:
- Android 11 CDD bölüm 2.2.7.3'te listelenen donanım gereksinimlerini karşılaması ZORUNLUDUR
Elde taşınır cihaz uygulamaları android.os.Build.VERSION_CODES.S
için android.os.Build.VERSION.MEDIA_PERFORMANCE_CLASS
değerini döndürürse, bunlar:
- [7.1.1.1/H-2-1] En az 1080p ekran çözünürlüğüne sahip OLMALIDIR.
- [7.1.1.3/H-2-1] Ekran yoğunluğu en az 400 dpi OLMALIDIR.
- [7.6.1/H-2-1] En az 6 GB fiziksel belleğe sahip OLMALIDIR.
2.2.7.4. Verim
Elde taşınır cihaz uygulamaları android.os.Build.VERSION_CODES.R
için android.os.Build.VERSION.MEDIA_PERFORMANCE_CLASS
değerini döndürürse, o zaman:
- Android 11 CDD bölüm 2.2.7.4'te listelenen performans gereksinimlerini karşılaması ZORUNLUDUR
Elde taşınır cihaz uygulamaları android.os.Build.VERSION_CODES.S
için android.os.Build.VERSION.MEDIA_PERFORMANCE_CLASS
değerini döndürürse, bunlar:
- [8.2/H-2-1] En az 125 MB/sn sıralı yazma performansı SAĞLAMALIDIR.
- [8.2/H-2-2] En az 10 MB/sn rastgele yazma performansı SAĞLAMALIDIR.
- [8.2/H-2-3] En az 250 MB/sn sıralı okuma performansı SAĞLAMALIDIR.
- [8.2/H-2-4] En az 40 MB/sn'lik rastgele okuma performansı ZORUNLUDUR.
2.3. Televizyon Gereksinimleri
Android Televizyon cihazı, yaklaşık 3 metre uzakta oturan kullanıcılar için ("arkaya yaslanan" veya "3 metrelik kullanıcı) dijital medyayı, filmleri, oyunları, uygulamaları ve/veya canlı TV'yi tüketmek için bir eğlence arayüzü olan bir Android cihaz uygulamasını ifade eder. arayüz").
Android cihaz uygulamaları, aşağıdaki kriterlerin tümünü karşılıyorsa Televizyon olarak sınıflandırılır:
- Kullanıcıdan on metre uzağa oturabilecek, ekranda oluşturulan kullanıcı arayüzünü uzaktan kontrol etmek için bir mekanizma sağladık.
- Çapraz uzunluğu 24 inçten daha büyük olan gömülü bir ekran görüntüsüne sahip olun VEYA ekran için VGA, HDMI, DisplayPort gibi bir video çıkış bağlantı noktası veya kablosuz bağlantı noktası ekleyin.
Bu bölümün geri kalanındaki ek gereksinimler, Android Televizyon cihazı uygulamalarına özeldir.
2.3.1. Donanım
Televizyon cihazı uygulamaları:
- [ 7.2 .2/T-0-1] D-pad'i desteklemelidir.
- [ 7.2 .3/T-0-1] Ana Sayfa ve Geri fonksiyonlarını sağlamalıdır ZORUNLU.
- [ 7.2 .3/T-0-2] Geri işlevinin (
KEYCODE_BACK
) hem normal hem de uzun basma olayını ön plandaki uygulamaya GÖNDERMELİDİR. - [ 7.2 .6.1/T-0-1] Oyun kumandaları için destek içermeli ve
android.hardware.gamepad
özellik işaretini beyan etmelidir. - [ 7.2 .7/T] Kullanıcıların dokunmatik olmayan navigasyona ve temel navigasyon tuşları girişlerine erişebilecekleri bir uzaktan kumanda SAĞLAMALIDIR.
Televizyon cihazı uygulamaları 3 eksenli bir jiroskop içeriyorsa:
- [ 7.3.4 /T-1-1] En az 100 Hz frekansa kadar olan olayları rapor edebilmelidir ZORUNLU.
- [ 7.3 .4/T-1-2] Saniyede 1000 dereceye kadar yönelim değişikliklerini ölçebilme kapasitesine sahip OLMALIDIR.
Televizyon cihazı uygulamaları:
- [ 7.4 .3/T-0-1] Bluetooth ve Bluetooth LE'yi desteklemelidir ZORUNLU.
- [ 7.6 .1/T-0-1] Uygulama özel verileri (diğer adıyla "/data" bölümü) için en az 4 GB kalıcı depolama alanına sahip olması GEREKİR.
Televizyon cihazı uygulamaları ana bilgisayar modunu destekleyen bir USB bağlantı noktası içeriyorsa:
- [ 7.5 .3/T-1-1] Bu USB bağlantı noktası üzerinden bağlanan ancak her zaman bağlı olması gerekmeyen harici bir kamera desteği içermelidir ZORUNLU.
TV cihazı uygulamaları 32 bit ise:
[ 7.6 .1/T-1-1] Aşağıdaki yoğunluklardan herhangi birinin kullanılması durumunda çekirdek ve kullanıcı alanının kullanabileceği bellek en az 896 MB OLMALIDIR:
- Küçük/normal ekranlarda 400 dpi veya üzeri
- Büyük ekranlarda xhdpi veya üstü
- Ekstra geniş ekranlarda tvdpi veya üzeri
TV cihazı uygulamaları 64 bit ise:
[ 7.6 .1/T-2-1] Aşağıdaki yoğunluklardan herhangi birinin kullanılması durumunda çekirdek ve kullanıcı alanının kullanabileceği bellek en az 1280 MB OLMALIDIR:
- Küçük/normal ekranlarda 400 dpi veya üzeri
- Büyük ekranlarda xhdpi veya üstü
- Ekstra geniş ekranlarda tvdpi veya üzeri
Yukarıdaki "çekirdek ve kullanıcı alanı tarafından kullanılabilen bellek" ifadesinin, aygıt uygulamalarında çekirdeğin kontrolü altında olmayan radyo, video vb. donanım bileşenlerine halihazırda ayrılmış herhangi bir belleğe ek olarak sağlanan bellek alanını ifade ettiğini unutmayın.
Televizyon cihazı uygulamaları:
- [ 7.8 .1/T] Bir mikrofon içermelidir.
- [ 7.8 .2/T-0-1] Bir ses çıkışına sahip olmalı ve
android.hardware.audio.output
olarak bildirilmelidir.
2.3.2. Multimedya
Televizyon cihazı uygulamalarının aşağıdaki ses kodlama ve kod çözme formatlarını desteklemesi ve bunları üçüncü taraf uygulamaların kullanımına sunması ZORUNLUdur:
- [ 5.1 /T-0-1] MPEG-4 AAC Profili (AAC LC)
- [ 5.1 /T-0-2] MPEG-4 HE AAC Profili (AAC+)
- [ 5.1 /T-0-3] AAC ELD (geliştirilmiş düşük gecikmeli AAC)
Televizyon cihazı uygulamalarının aşağıdaki video kodlama formatlarını desteklemesi ve bunları üçüncü taraf uygulamaların kullanımına sunması ZORUNLUDUR:
Televizyon cihazı uygulamaları:
- [ 5.2 .2/T-SR-1] Saniyede 30 kare hızında 720p ve 1080p çözünürlüklü videoların H.264 kodlamasını desteklemesi KESİNLİKLE ÖNERİLİR.
Televizyon cihazı uygulamalarının aşağıdaki video kod çözme formatlarını desteklemesi ve bunları üçüncü taraf uygulamaların kullanımına sunması ZORUNLUDUR:
- [ 5.3.3 /T-0-1] MPEG-4 SP
- [ 5.3.4 /T-0-2] H.264 AVC
- [ 5.3.5 /T-0-3] H.265 HEVC
- [ 5.3.6 /T-0-4] VP8
- [ 5.3.7 /T-0-5] VP9
- [ 5.3.1 /T-0-6] MPEG-2
Televizyon cihazı uygulamaları, Bölüm 5.3.1'de ayrıntılı olarak açıklandığı gibi, aşağıdakilere kadar standart video kare hızlarında ve çözünürlüklerinde MPEG-2 kod çözmeyi desteklemelidir ZORUNLU:
- [ 5.3.1 /T-1-1] Ana Profil Yüksek Seviyesi ile saniyede 29,97 kare hızında HD 1080p.
- [ 5.3.1 /T-1-2] Ana Profil Yüksek Seviyesi ile saniyede 59,94 kare hızında HD 1080i. Taramalı MPEG-2 videonun taramasını kaldırmalı ve bunu üçüncü taraf uygulamaların kullanımına sunmalıdırlar.
Televizyon cihazı uygulamaları, Bölüm 5.3.4'te ayrıntılı olarak açıklandığı gibi, aşağıdakilere kadar standart video kare hızlarında ve çözünürlüklerde H.264 kod çözmeyi desteklemelidir ZORUNLU:
- [ 5.3.4 /T-1-1] Baseline Profile ile saniyede 60 kare HD 1080p
- [ 5.3.4 /T-1-2] Ana Profil ile saniyede 60 kare hızında HD 1080p
- [ 5.3.4 /T-1-3] Yüksek Profil Seviyesi 4.2 ile saniyede 60 karede HD 1080p
H.265 donanım kod çözücülere sahip televizyon cihazı uygulamaları, Bölüm 5.3.5'te ayrıntılı olarak belirtildiği gibi, aşağıdakilere kadar standart video kare hızlarında ve çözünürlüklerde H.265 kod çözmeyi desteklemelidir ZORUNLU:
- [ 5.3.5 /T-1-1] Ana Profil Seviyesi 4.1 ile saniyede 60 karede HD 1080p
H.265 donanım kod çözücülere sahip Televizyon cihazı uygulamaları H.265 kod çözmeyi ve UHD kod çözme profilini destekliyorsa:
- [ 5.3.5 /T-2-1] Main10 Seviye 5 Ana Katman profiliyle saniyede 60 kare hızında UHD kod çözme profilini desteklemelidir ZORUNLU
Televizyon cihazı uygulamaları, Bölüm 5.3.6'da ayrıntılı olarak açıklandığı gibi, aşağıdakilere kadar standart video kare hızlarında ve çözünürlüklerinde VP8 kod çözmeyi desteklemelidir ZORUNLU:
- [ 5.3.6 /T-1-1] Saniyede 60 kare kod çözme profilinde HD 1080p
VP9 donanım kod çözücülerine sahip televizyon cihazı uygulamaları, Bölüm 5.3.7'de ayrıntılı olarak açıklandığı gibi, aşağıdakilere kadar ve aşağıdakiler de dahil olmak üzere standart video kare hızlarında ve çözünürlüklerinde VP9 kod çözmeyi desteklemelidir ZORUNLU:
- [ 5.3.7 /T-1-1] Profil 0 (8 bit renk derinliği) ile saniyede 60 karede HD 1080p
VP9 donanım kod çözücülere sahip Televizyon cihazı uygulamaları VP9 kod çözmeyi ve UHD kod çözme profilini destekliyorsa:
- [ 5.3.7 /T-2-1] Profil 0 (8 bit renk derinliği) ile saniyede 60 kare UHD kod çözme profilini desteklemelidir ZORUNLU.
- [ 5.3.7 /T-2-1] Profil 2 (10 bit renk derinliği) ile saniyede 60 kare hızında UHD kod çözme profilini desteklemeleri KESİNLİKLE ÖNERİR.
Televizyon cihazı uygulamaları:
- [ 5.5 /T-0-1] Sıkıştırılmış ses geçiş çıkışı (cihazda ses kod çözme işleminin yapılmadığı durum) haricinde, desteklenen çıkışlarda sistem Ana Ses Düzeyi ve dijital ses çıkışı ses düzeyi zayıflaması desteğini içermelidir ZORUNLU.
Televizyon cihazı uygulamalarında yerleşik bir ekran yoksa, bunun yerine HDMI aracılığıyla bağlanan harici bir ekranı destekliyorsa:
- [ 5.8 /T-0-1] 50Hz veya 60Hz yenileme hızıyla desteklenebilecek maksimum çözünürlüğü seçecek şekilde HDMI çıkış modunu ayarlamanız GEREKİR.
- [ 5.8 /T-SR-1] Kullanıcı tarafından yapılandırılabilen bir HDMI yenileme hızı seçici sağlaması KESİNLİKLE TAVSİYE EDİLİR.
- [ 5.8 ] HDMI çıkış modu yenileme hızını, cihazın satıldığı bölgenin video yenileme hızına bağlı olarak 50Hz veya 60Hz olarak ayarlaması GEREKİR.
Televizyon cihazı uygulamalarında yerleşik bir ekran yoksa, bunun yerine HDMI aracılığıyla bağlanan harici bir ekranı destekliyorsa:
- [ 5.8 /T-1-1] HDCP 2.2'yi desteklemelidir.
Televizyon cihazı uygulamaları UHD kod çözmeyi desteklemiyor ancak bunun yerine HDMI aracılığıyla bağlanan harici bir ekranı destekliyorsa:
- [ 5.8 /T-2-1] HDCP 1.4'ü desteklemelidir
2.3.3. Yazılım
Televizyon cihazı uygulamaları:
- [ 3 /T-0-1]
android.software.leanback
veandroid.hardware.type.television
özelliklerini beyan etmesi ZORUNLUDUR. - [ 3.2.3.1 /T-0-1] Burada listelenen aşağıdaki uygulama amaçları tarafından tanımlanan tüm genel amaç filtre modelleri için bir veya daha fazla uygulamayı veya hizmet bileşenini bir amaç işleyiciyle önceden yüklemesi ZORUNLUDUR.
- [ 3.4 .1/T-0-1]
android.webkit.Webview
API'sinin eksiksiz bir uygulamasını SAĞLAMALIDIR.
Android Television cihaz uygulamaları kilit ekranını destekliyorsa:
- [ 3.8 .10/T-1-1] Medya Bildirim Şablonu da dahil olmak üzere Kilit ekranı Bildirimlerinin görüntülenmesi ZORUNLUDUR.
Televizyon cihazı uygulamaları:
- [ 3.8 .14/T-SR-1] Resim içinde resim (PIP) modu çoklu pencereyi desteklemesi KESİNLİKLE TAVSİYE EDİLİR.
- [ 3.10 /T-0-1] Üçüncü taraf erişilebilirlik hizmetlerini desteklemelidir ZORUNLU.
- [ 3.10 /T-SR-1] Anahtar Erişimi ve TalkBack (önceden yüklenmiş Metin-konuşma motoru tarafından desteklenen diller için) erişilebilirlik hizmetleriyle karşılaştırılabilir veya bunların işlevselliğini aşan erişilebilirlik hizmetlerinin cihaza önceden yüklenmesi ŞİDDETLE ÖNERİLİR. talkback açık kaynak projesi .
Televizyon cihazı uygulamaları android.hardware.audio.output
özelliğini bildirirse:
- [ 3.11 /T-SR-1] Cihazda mevcut dilleri destekleyen bir TTS motorunun dahil edilmesi KESİNLİKLE TAVSİYE EDİLİR.
- [ 3.11 /T-1-1] Üçüncü taraf TTS motorlarının kurulumunu desteklemelidir ZORUNLU.
Televizyon cihazı uygulamaları:
- [ 3.12 /T-0-1] TV Giriş Çerçevesini desteklemelidir ZORUNLU.
2.3.4. Performans ve Güç
- [ 8.1 /T-0-1] Tutarlı kare gecikmesi . Tutarsız kare gecikmesi veya karelerin oluşturulmasındaki gecikme, saniyede 5 kareden daha sık OLMAMALIDIR ve saniyede 1 karenin altında OLMALIDIR.
- [ 8.2 /T-0-1] En az 5 MB/sn sıralı yazma performansı SAĞLAMALIDIR.
- [ 8.2 /T-0-2] En az 0,5 MB/sn'lik rastgele yazma performansı SAĞLAMALIDIR.
- [ 8.2 /T-0-3] En az 15MB/s sıralı okuma performansı ZORUNLUDUR.
- [ 8.2 /T-0-4] En az 3,5 MB/sn'lik rastgele okuma performansı ZORUNLUDUR.
Televizyon cihazı uygulamaları, AOSP'de bulunan cihaz güç yönetimini iyileştirmeye yönelik özellikler içeriyorsa veya AOSP'de bulunan özellikleri genişletiyorsa:
- [ 8.3 /T-1-1] Pil tasarrufu özelliğini etkinleştirmek ve devre dışı bırakmak için kullanıcıya olanak sağlamalıdır ZORUNLU.
Televizyon cihazı uygulamalarının pili yoksa:
- [ 8.3 /T-1-2] Cihazı, Pilsiz Cihazların Desteklenmesi bölümünde açıklandığı gibi pilsiz bir cihaz olarak kaydetmesi GEREKİR.
Televizyon cihazı uygulamalarının pili varsa:
- [ 8.3 /T-1-3] Uygulama Bekleme ve Doze güç tasarrufu modlarından muaf tutulan tüm uygulamaları görüntülemek için kullanıcıya olanak sağlamalıdır ZORUNLU.
Televizyon cihazı uygulamaları:
- [ 8.4 /T-0-1] Android Açık Kaynak Projesi sitesinde belgelendiği gibi, her donanım bileşeni için mevcut tüketim değerini ve bileşenlerin zaman içinde neden olduğu yaklaşık pil tüketimini tanımlayan bileşen başına bir güç profili sağlamalıdır ZORUNLU.
- [ 8.4 /T-0-2] Tüm güç tüketimi değerleri miliamper saat (mAh) cinsinden bildirilmelidir ZORUNLU.
- [ 8.4 /T-0-3] Her işlemin UID'sine göre CPU güç tüketimini bildirmesi ZORUNLUDUR. Android Açık Kaynak Projesi, gereksinimi
uid_cputime
çekirdek modülü uygulaması aracılığıyla karşılar. - [ 8.4 /T] Donanım bileşeni güç kullanımını bir uygulamaya ilişkilendiremiyorsanız, donanım bileşeninin kendisine atfedilmesi GEREKİR.
- [ 8.4 /T-0-4] Bu güç kullanımını, uygulama geliştiricisinin
adb shell dumpsys batterystats
kabuk komutu aracılığıyla kullanılabilir hale getirmesi ZORUNLUDUR.
2.3.5. Güvenlik Modeli
Televizyon cihazı uygulamaları:
- [ 9.11 /T-0-1] Anahtar deposu uygulamasını yalıtılmış bir yürütme ortamıyla yedeklemek ZORUNLUDUR.
- [ 9.11 /T-0-2] Android Anahtar Deposu sisteminin desteklenen algoritmalarını güvenli bir şekilde izole edilmiş bir alanda düzgün bir şekilde desteklemek için RSA, AES, ECDSA ve HMAC şifreleme algoritmalarının ve MD5, SHA1 ve SHA-2 ailesi karma işlevlerinin uygulamalarına sahip olması ZORUNLUDUR çekirdek ve üzeri üzerinde çalışan koddan. Güvenli izolasyon, çekirdek veya kullanıcı alanı kodunun, DMA dahil, izole edilmiş ortamın dahili durumuna erişebileceği tüm potansiyel mekanizmaları ENGELLEMELİDİR. Yukarı akışlı Android Açık Kaynak Projesi (AOSP), Trusty uygulamasını kullanarak bu gereksinimi karşılar, ancak başka bir ARM TrustZone tabanlı çözüm veya uygun bir hipervizör tabanlı izolasyonun üçüncü taraflarca gözden geçirilmiş güvenli uygulaması alternatif seçeneklerdir.
- [ 9.11 /T-0-3] Kilit ekranı kimlik doğrulamasını yalıtılmış yürütme ortamında gerçekleştirmeli ve yalnızca başarılı olduğunda, kimlik doğrulamaya bağlı anahtarların kullanılmasına izin vermelidir. Kilit ekranı kimlik bilgileri, yalnızca yalıtılmış yürütme ortamının kilit ekranı kimlik doğrulamasını gerçekleştirmesine izin verecek şekilde saklanmalıdır *ZORUNLU*. Yukarı akışlı Android Açık Kaynak Projesi, bu gereksinimi karşılamak için kullanılabilecek Gatekeeper Donanım Soyutlama Katmanı (HAL) ve Trusty'yi sağlar.
- [ 9.11 /T-0-4] Onay imzalama anahtarının güvenli donanım tarafından korunduğu ve imzalamanın güvenli donanımda gerçekleştirildiği anahtar doğrulamayı desteklemelidir ZORUNLU. Anahtarların cihaz tanımlayıcıları olarak kullanılmasını önlemek için, doğrulama imzalama anahtarlarının yeterli sayıda cihaz arasında paylaşılması ZORUNLUDUR. Bu gereksinimi karşılamanın bir yolu, belirli bir SKU'dan en az 100.000 birim üretilmediği sürece aynı doğrulama anahtarını paylaşmaktır. Bir SKU'nun 100.000 biriminden fazla üretilmesi durumunda her 100.000 birim için farklı bir anahtar KULLANILABİLİR.
- [9/T-0-1] 'android.hardware.security.model.uyumlu' özelliğinin bildirilmesi ZORUNLUDUR.
Bir cihaz uygulaması daha önceki bir Android sürümünde zaten başlatılmışsa, bu tür bir cihazın, yalıtılmış bir yürütme ortamı tarafından desteklenen bir anahtar deposuna sahip olma ve android.hardware.fingerprint
doğrulamayı destekleme gerekliliğinden muaf tutulacağını unutmayın; yalıtılmış bir yürütme ortamı tarafından desteklenen bir anahtar deposu gerektirir.
Televizyon cihazı uygulamaları güvenli bir kilit ekranını destekliyorsa:
- [ 9.11 /T-1-1] Kullanıcının kilit açık durumdan kilitli duruma geçiş için Uyku zaman aşımını seçmesine izin vermesi ZORUNLUdur ve izin verilen minimum zaman aşımı süresi 15 saniye veya daha azdır.
Televizyon cihazı uygulamaları birden fazla kullanıcı içeriyorsa ve android.hardware.telephony
özellik işaretini bildirmiyorsa, bunlar:
- [ 9.5 /T-2-1] Cihaz sahiplerinin cihazdaki ek kullanıcıları ve bunların yeteneklerini yönetmesine olanak tanıyan bir özellik olan kısıtlı profilleri desteklemesi ZORUNLUDUR. Kısıtlanmış profiller sayesinde cihaz sahipleri, ek kullanıcıların çalışabileceği ayrı ortamları hızlı bir şekilde oluşturabilir ve bu ortamlarda bulunan uygulamalardaki daha ayrıntılı kısıtlamaları yönetebilir.
Televizyon cihazı uygulamaları birden fazla kullanıcı içeriyorsa ve android.hardware.telephony
özellik işaretini bildiriyorsa, bunlar:
- [ 9.5 /T-3-1] Kısıtlanmış profilleri desteklememelidir ZORUNLU, ancak diğer kullanıcıların sesli çağrılara ve SMS'e erişimini etkinleştirmek/devre dışı bırakmak için AOSP kontrol uygulamasıyla uyumlu OLMALIDIR.
Televizyon cihazı uygulamaları android.hardware.microphone
olarak bildirirse:
- [ 9.8.2 /T-4-1] Bir uygulama mikrofondan ses verilerine erişirken mikrofon göstergesinin görüntülenmesi ZORUNLUDUR, ancak mikrofona yalnızca HotwordDetectionService, SOURCE_HOTWORD, ContentCaptureService veya burada belirtilen rolleri taşıyan uygulamalar tarafından erişildiğinde bu görüntülenmemelidir. Bölüm 9.1 CDD tanımlayıcı C-3-X ile izinler].
- [ 9.8.2 /T-4-2] Görünür kullanıcı arayüzlerine veya doğrudan kullanıcı etkileşimine sahip sistem uygulamaları için mikrofon göstergesini GİZLEMEMELİDİR.
Televizyon cihazı uygulamaları android.hardware.camera.any
olarak bildirirse:
- [ 9.8.2 /T-5-1] Bir uygulama canlı kamera verilerine erişirken kamera göstergesinin görüntülenmesi ZORUNLUDUR, ancak kameraya yalnızca Bölüm 9.1 CDD ile İzinler'de belirtilen rollere sahip uygulamalar tarafından erişildiği zaman görüntülenmemelidir. tanımlayıcı [C-3-X].
- [ 9.8.2 /T-5-2] Görünür kullanıcı arayüzlerine veya doğrudan kullanıcı etkileşimine sahip sistem uygulamaları için kamera göstergesini GİZLEMEMELİDİR.
2.3.6. Geliştirici Araçları ve Seçenekleri Uyumluluğu
Televizyon cihazı uygulamaları:
- mükemmel
- [ 6.1 /T-0-1] Kabuk kullanıcısına, perfetto belgelerine uygun olan cmdline'ın bir
/system/bin/perfetto
ikili dosyasını sunması GEREKİR. - [ 6.1 /T-0-2] Perfetto ikilisi , perfetto belgelerinde tanımlanan şemaya uygun bir protobuf yapılandırmasını giriş olarak kabul etmelidir ZORUNLU.
- [ 6.1 /T-0-3] Perfetto ikilisinin , perfetto belgelerinde tanımlanan şemaya uygun bir protobuf izini çıktı olarak yazması ZORUNLUDUR.
- [ 6.1 /T-0-4] perfetto ikili dosyası aracılığıyla en azından perfetto belgelerinde açıklanan veri kaynaklarını sağlamalıdır ZORUNLU.
- [ 6.1 /T-0-1] Kabuk kullanıcısına, perfetto belgelerine uygun olan cmdline'ın bir
2.4. Gereksinimleri İzle
Android Watch cihazı, vücuda, belki de bileğe takılması amaçlanan bir Android cihaz uygulamasını ifade eder.
Android cihaz uygulamaları, aşağıdaki kriterlerin tümünü karşılıyorsa İzleme olarak sınıflandırılır:
- Fiziksel diyagonal uzunluğu 1,1 ila 2,5 inç arasında olan bir ekrana sahip olun.
- Vücuda takılabilecek mekanizmaya sahiptir.
Bu bölümün geri kalanındaki ek gereksinimler, Android Watch cihaz uygulamalarına özeldir.
2.4.1. Donanım
Cihaz uygulamalarını izleyin:
[ 7.1 .1.1/W-0-1] Fiziksel diyagonal boyutu 1,1 ila 2,5 inç aralığında olan bir ekrana sahip OLMALIDIR.
[ 7.2 .3/W-0-1] Kullanıcının Home işlevine ve
UI_MODE_TYPE_WATCH
dışında Geri işlevine sahip olması ZORUNLUDUR.[ 7.2 .4/W-0-1] Dokunmatik ekran girişini desteklemelidir ZORUNLU.
[ 7.3 .1/W-SR-1] 3 eksenli bir ivmeölçer içermesi KESİNLİKLE TAVSİYE EDİLİR.
İzleme cihazı uygulamaları bir GPS/GNSS alıcısı içeriyorsa ve bu özelliği uygulamalara android.hardware.location.gps
özellik işareti aracılığıyla rapor ediyorsa, bunlar:
- [ 7.3 .3/W-1-1] GPS/GNSS'den hesaplanan konum henüz rapor edilmemiş olsa bile, GNSS ölçümlerini bulunur bulunmaz rapor etmesi ZORUNLUDUR.
- [ 7.3 .3/W-1-2] Konumu belirledikten sonra, açık gökyüzü koşullarında, sabit veya saniyede 0,2 metre kareden daha az ivme ile hareket halindeyken hesaplamak için yeterli olan GNSS sözde mesafelerini ve sözde mesafe oranlarını rapor etmelidir. zamanın en az %95'inde konum 20 metre ve hız 0,2 metre/saniye dahilinde olmalıdır.
Watch cihazı uygulamaları 3 eksenli bir jiroskop içeriyorsa:
- [ 7.3.4 /W-2-1] Saniyede 1000 dereceye kadar yönelim değişikliklerini ölçebilme kapasitesine sahip OLMALIDIR.
Cihaz uygulamalarını izleyin:
[ 7.4 .3/W-0-1] Bluetooth'u desteklemelidir.
[ 7.6 .1/W-0-1] Uygulama özel verileri (diğer adıyla "/data" bölümü) için en az 1 GB kalıcı depolama alanına sahip olması GEREKİR.
[ 7.6 .1/W-0-2] Çekirdek ve kullanıcı alanı için en az 416 MB belleğe sahip olması GEREKİR.
[ 7.8 .1/W-0-1] Bir mikrofon içermelidir ZORUNLU.
[ 7.8 .2/W] ses çıkışı OLABİLİR.
2.4.2. Multimedya
Ek gereksinim yok.
2.4.3. Yazılım
Cihaz uygulamalarını izleyin:
- [ 3 /W-0-1]
android.hardware.type.watch
özelliğini bildirmeniz ZORUNLUDUR. - [ 3 /W-0-2] uiMode = UI_MODE_TYPE_WATCH'u desteklemelidir ZORUNLU.
- [ 3.2.3.1 /W-0-1] Burada listelenen aşağıdaki uygulama amaçları tarafından tanımlanan tüm genel amaç filtre modelleri için bir veya daha fazla uygulamayı veya hizmet bileşenini bir amaç işleyiciyle önceden yüklemesi ZORUNLUDUR.
Cihaz uygulamalarını izleyin:
- [ 3.8 .4/W-SR-1] Destek eylemini gerçekleştirecek bir asistanın cihaza uygulanması KESİNLİKLE TAVSİYE EDİLİR.
android.hardware.audio.output
özellik işaretini bildiren cihaz uygulamalarını izleyin:
- [ 3.10 /W-1-1] Üçüncü taraf erişilebilirlik hizmetlerini desteklemelidir ZORUNLU.
- [ 3.10 /W-SR-1] Anahtar Erişimi ve TalkBack (önceden yüklenmiş Metin-konuşma motoru tarafından desteklenen diller için) erişilebilirlik hizmetleriyle karşılaştırılabilir veya bunların işlevselliğini aşan erişilebilirlik hizmetlerinin cihaza önceden yüklenmesi ŞİDDETLE ÖNERİR. talkback açık kaynak projesi .
Watch cihazı uygulamaları android.hardware.audio.output özelliğini bildirirse:
[ 3.11 /W-SR-1] Cihazda mevcut dilleri destekleyen bir TTS motorunun dahil edilmesi KESİNLİKLE TAVSİYE EDİLİR.
[ 3.11 /W-0-1] Üçüncü taraf TTS motorlarının kurulumunu desteklemelidir ZORUNLU.
2.4.4. Performans ve Güç
Watch cihazı uygulamaları, AOSP'de bulunan cihaz güç yönetimini iyileştirmeye yönelik özellikler içeriyorsa veya AOSP'de bulunan özellikleri genişletiyorsa:
- [ 8.3 /W-SR-1] Kullanıcıya Uygulamayı Beklemede ve Doze güç tasarrufu modlarından muaf tutulan tüm uygulamaları görüntüleme olanağı sağlaması KESİNLİKLE TAVSİYE EDİLİR.
- [ 8.3 /W-SR-2] Kullanıcıya pil tasarrufu özelliğini etkinleştirme ve devre dışı bırakma olanağı sağlaması KESİNLİKLE TAVSİYE EDİLİR.
Cihaz uygulamalarını izleyin:
- [ 8.4 /W-0-1] Android Açık Kaynak Projesi sitesinde belgelendiği gibi, her donanım bileşeni için geçerli tüketim değerini ve bileşenlerin zaman içinde neden olduğu yaklaşık pil tüketimini tanımlayan bileşen başına bir güç profili SAĞLAMALIDIR.
- [ 8.4 /W-0-2] Tüm güç tüketimi değerleri miliamper saat (mAh) cinsinden bildirilmelidir ZORUNLU.
- [ 8.4 /W-0-3] Her işlemin UID'sine göre CPU güç tüketimini bildirmesi ZORUNLUDUR. Android Açık Kaynak Projesi, gereksinimi
uid_cputime
çekirdek modülü uygulaması aracılığıyla karşılar. - [ 8.4 /W-0-4] Bu güç kullanımını, uygulama geliştiricisinin
adb shell dumpsys batterystats
kabuk komutu aracılığıyla kullanılabilir hale getirmesi ZORUNLUDUR. - [ 8.4 /W] Donanım bileşeni güç kullanımını bir uygulamaya ilişkilendiremiyorsanız, donanım bileşeninin kendisine atfedilmesi GEREKLİDİR.
2.4.5. Güvenlik Modeli
Cihaz uygulamalarını izleyin:
- [9/W-0-1]
android.hardware.security.model.compatible
özelliğinin bildirilmesi ZORUNLUDUR.
Watch cihazı uygulamaları birden fazla kullanıcı içeriyorsa ve android.hardware.telephony
özellik işaretini bildirmiyorsa, bunlar:
- [ 9.5 /W-1-1] Cihaz sahiplerinin cihazdaki ek kullanıcıları ve onların yeteneklerini yönetmesine olanak tanıyan bir özellik olan kısıtlı profilleri desteklemesi ZORUNLUDUR. Kısıtlanmış profiller sayesinde cihaz sahipleri, ek kullanıcıların çalışabileceği ayrı ortamları hızlı bir şekilde oluşturabilir ve bu ortamlarda bulunan uygulamalardaki daha ayrıntılı kısıtlamaları yönetebilir.
Watch cihazı uygulamaları birden fazla kullanıcı içeriyorsa ve android.hardware.telephony
özellik işaretini bildiriyorsa, bunlar:
- [ 9.5 /W-2-1] Kısıtlanmış profilleri DESTEKLEMEMELİDİR ancak diğer kullanıcıların sesli çağrılara ve SMS'lere erişimini etkinleştirmek/devre dışı bırakmak için AOSP kontrol uygulamasıyla uyumlu OLMALIDIR.
2.5. Otomotiv Gereksinimleri
Android Automotive uygulaması, sistemin bir kısmı veya tamamı ve/veya bilgi-eğlence işlevselliği için işletim sistemi olarak Android çalıştıran bir araç ana ünitesini ifade eder.
Android cihaz uygulamaları, android.hardware.type.automotive
özelliğini bildiriyorsa veya aşağıdaki kriterlerin tümünü karşılıyorsa Otomotiv olarak sınıflandırılır.
- Bir otomotiv aracının parçası olarak gömülüdür veya takılabilir.
- Ana ekran olarak sürücü koltuğu sırasındaki bir ekranı kullanıyoruz.
Bu bölümün geri kalanındaki ek gereksinimler, Android Automotive cihaz uygulamalarına özeldir.
2.5.1. Donanım
Otomotiv cihaz uygulamaları:
- [ 7.1 .1.1/A-0-1] Fiziksel diyagonal boyutta en az 6 inç ekrana sahip olması ZORUNLUDUR.
[ 7.1 .1.1/A-0-2] En az 750 dp x 480 dp ekran boyutu düzenine sahip OLMALIDIR.
[ 7.2 .3/A-0-1] Ana Sayfa işlevini sağlamalıdır ZORUNLU ve Geri ve Son işlevlerini de SAĞLAYABİLİR.
[ 7.2 .3/A-0-2] Geri işlevinin (
KEYCODE_BACK
) hem normal hem de uzun basma olayını ön plandaki uygulamaya GÖNDERMELİDİR.[ 7.3 /A-0-1]
GEAR_SELECTION
,NIGHT_MODE
,PERF_VEHICLE_SPEED
vePARKING_BRAKE_ON
öğelerini uygulamalı ve rapor etmelidir ZORUNLU.[ 7.3 /A-0-2]
NIGHT_MODE
bayrağının değeri, gösterge tablosunun gündüz/gece moduyla tutarlı OLMALIDIR ve ortam ışığı sensörü girdisine dayalı OLMALIDIR. Temel ortam ışığı sensörü Fotometre ile aynı OLABİLİR.[ 7.3 /A-0-3] Sağlanan her sensör için SensorAdditionalInfo'nun parçası olarak sensör ek bilgi alanı
TYPE_SENSOR_PLACEMENT
SAĞLANMALIDIR.[ 7.3 /A-0-1] GPS/GNSS'yi ek sensörlerle birleştirerek konumu kesin olarak hesaplayabilir. Konum tam olarak hesaba katılmıyorsa, ilgili Sensör türlerinin ve/veya kullanılan Araç Özellik Kimliklerinin uygulanması ve raporlanması KESİNLİKLE TAVSİYE EDİLİR.
[ 7.3 /A-0-2] LocationManager#requestLocationUpdates() aracılığıyla istenen Konum , haritayla eşleşmemelidir.
Otomotiv cihaz uygulamaları OpenGL ES 3.1'i destekliyorsa:
- [ 7.1 .4.1/A-0-1] OpenGL ES 3.1 veya üstünü beyan etmelidir.
- [ 7.1 .4.1/A-0-2] Vulkan 1.1'i desteklemelidir.
- [ 7.1 .4.1/A-0-3] Vulkan yükleyiciyi içermeli ve tüm sembolleri dışa aktarmalıdır.
Otomotiv cihazı uygulamaları 3 eksenli bir ivmeölçer içeriyorsa:
- [ 7.3.1 /A-1-1] En az 100 Hz frekansa kadar olan olayları rapor edebilmelidir ZORUNLU.
- [ 7.3 .1/A-1-2] Android araç sensörü koordinat sistemine uygun OLMALIDIR.
Otomotiv cihazı uygulamaları 3 eksenli bir jiroskop içeriyorsa:
- [ 7.3.4 /A-2-1] En az 100 Hz frekansa kadar olan olayları rapor edebilmelidir ZORUNLU.
- [ 7.3 .4/A-2-3] Saniyede 250 dereceye kadar yönelim değişikliklerini ölçebilme kapasitesine sahip OLMALIDIR.
- [ 7.3 .4/A-SR-1] Mümkün olan çözünürlüğü en üst düzeye çıkarmak için jiroskopun ölçüm aralığını +/-250dps olarak yapılandırmanız KESİNLİKLE TAVSİYE EDİLİR
Otomotiv cihaz uygulamaları bir GPS/GNSS alıcısı içeriyor ancak hücresel ağ tabanlı veri bağlantısını içermiyorsa:
- [ 7.3 .3/A-3-1] GPS/GNSS alıcısı ilk açıldığında veya 4+ gün sonra 60 saniye içinde konumu belirlemesi ZORUNLUDUR.
- [ 7.3 .3/A-3-2] Diğer tüm konum istekleri için 7.3.3/C-1-2 ve 7.3.3/C-1-6'da açıklanan ilk düzeltme süresi kriterlerini karşılaması ZORUNLUDUR ( yani ilk kez olmayan veya 4+ günden sonra olmayan istekler). 7.3.3/C-1-2 gerekliliği tipik olarak hücresel ağ tabanlı veri bağlantısı olmayan araçlarda, alıcıda hesaplanan GNSS yörünge tahminleri kullanılarak veya bilinen son araç konumu ile birlikte kesin hesaplama yeteneği kullanılarak karşılanır. 7.3.3/C-1-3'ü karşılayan bir konum doğruluğu veya her ikisinin bir kombinasyonu ile en az 60 saniye.
Otomotiv cihaz uygulamaları:
- [ 7.4 .3/A-0-1] Bluetooth'u desteklemelidir ve Bluetooth LE'yi desteklemelidir.
- [ 7.4 .3/A-0-2] Android Automotive uygulamalarının aşağıdaki Bluetooth profillerini desteklemesi ZORUNLUDUR:
- Eller Serbest Profili (HFP) üzerinden telefon görüşmesi.
- Ses Dağıtım Profili (A2DP) üzerinden medya oynatma.
- Uzaktan Kumanda Profili (AVRCP) üzerinden medya oynatma kontrolü.
- Telefon Rehberi Erişim Profilini (PBAP) kullanarak kişi paylaşımı.
[ 7.4 .3/A-SR-1] Mesaj Erişim Profilini (MAP) desteklemeleri KESİNLİKLE TAVSİYE EDİLİR.
[ 7.4 .5/A] Hücresel ağ tabanlı veri bağlantısı desteğini içermelidir GEREKLİ.
[ 7.4 .5/A] Sistem uygulamalarının kullanması gereken ağlar için Sistem API'si
NetworkCapabilities#NET_CAPABILITY_OEM_PAID
sabitini KULLANABİLİR.
Dış görüş kamerası, araç kamerası gibi cihaz uygulamasının dışındaki sahneleri görüntüleyen bir kameradır.
Otomotiv cihaz uygulamaları:
- Bir veya daha fazla dış görüş kamerası içermelidir.
Otomotiv cihaz uygulamaları bir dış görüş kamerası içeriyorsa, böyle bir kamera için bunlar:
- [ 7.5 /A-1-1] Kameranın temel gereksinimlerine uymadıkları sürece, Android Kamera API'leri aracılığıyla erişilebilen dış görüş kameralarına sahip OLMAMALIDIR.
- [ 7.5 /A-SR-1] Kamera önizlemesini döndürmemeniz veya yatay olarak yansıtmamanız KESİNLİKLE TAVSİYE EDİLİR.
- [ 7.5 .5/A-SR-1] Kameranın uzun boyutunun ufukla aynı hizada olacağı şekilde yönlendirilmesi KESİNLİKLE TAVSİYE EDİLİR.
- [ 7.5 /A-SR-2] En az 1,3 megapiksel çözünürlüğe sahip olmaları KESİNLİKLE TAVSİYE EDİLİR.
- Sabit odaklı veya EDOF (genişletilmiş alan derinliği) donanımına sahip OLMALIDIR.
- Android senkronizasyon çerçevesini desteklemelidir.
- Kamera sürücüsünde donanım otomatik odaklama veya yazılım otomatik odaklama uygulanmış OLABİLİR.
Otomotiv cihaz uygulamaları:
[ 7.6 .1/A-0-1] Uygulama özel verileri (diğer adıyla "/data" bölümü) için en az 4 GB kalıcı depolama alanına sahip olması GEREKİR.
[ 7.6 .1/A] Veri bölümünü, örneğin
f2fs
dosya sistemini kullanarak, flash depolamada gelişmiş performans ve uzun ömür sağlayacak şekilde biçimlendirmelidir GEREKLİ.
Otomotiv cihazı uygulamaları, dahili çıkarılabilir olmayan depolamanın bir kısmı aracılığıyla paylaşılan harici depolama sağlıyorsa:
- [ 7.6 .1/A-SR-1] Harici depolamada gerçekleştirilen işlemlerde, örneğin
SDCardFS
kullanılarak G/Ç yükünün azaltılması KESİNLİKLE ÖNERİLİR.
Otomotiv cihazı uygulamaları 32 bit ise:
[ 7.6 .1/A-1-1] Aşağıdaki yoğunluklardan herhangi birinin kullanılması durumunda çekirdek ve kullanıcı alanının kullanabileceği bellek en az 512 MB OLMALIDIR:
- Küçük/normal ekranlarda 280 dpi veya daha düşük
- Ekstra geniş ekranlarda ldpi veya daha düşük
- Büyük ekranlarda mdpi veya daha düşük
[ 7.6 .1/A-1-2] Aşağıdaki yoğunluklardan herhangi birinin kullanılması durumunda çekirdek ve kullanıcı alanının kullanabileceği bellek en az 608 MB OLMALIDIR:
- Küçük/normal ekranlarda xhdpi veya üstü
- Büyük ekranlarda hdpi veya üstü
- Ekstra geniş ekranlarda mdpi veya üstü
[ 7.6 .1/A-1-3] Aşağıdaki yoğunluklardan herhangi birinin kullanılması durumunda çekirdek ve kullanıcı alanının kullanabileceği bellek en az 896 MB OLMALIDIR:
- Küçük/normal ekranlarda 400 dpi veya üzeri
- Büyük ekranlarda xhdpi veya üstü
- Ekstra geniş ekranlarda tvdpi veya üzeri
[ 7.6 .1/A-1-4] Aşağıdaki yoğunluklardan herhangi birinin kullanılması durumunda çekirdek ve kullanıcı alanının kullanabileceği bellek en az 1344 MB OLMALIDIR:
- Küçük/normal ekranlarda 560dpi veya üzeri
- Büyük ekranlarda 400 dpi veya daha yüksek
- Ekstra geniş ekranlarda xhdpi veya üstü
Otomotiv cihazı uygulamaları 64 bit ise:
[ 7.6 .1/A-2-1] Aşağıdaki yoğunluklardan herhangi birinin kullanılması durumunda çekirdek ve kullanıcı alanının kullanabileceği bellek en az 816 MB OLMALIDIR:
- Küçük/normal ekranlarda 280 dpi veya daha düşük
- Ekstra geniş ekranlarda ldpi veya daha düşük
- Büyük ekranlarda mdpi veya daha düşük
[ 7.6 .1/A-2-2] Aşağıdaki yoğunluklardan herhangi birinin kullanılması durumunda çekirdek ve kullanıcı alanının kullanabileceği bellek en az 944 MB OLMALIDIR:
- Küçük/normal ekranlarda xhdpi veya üstü
- Büyük ekranlarda hdpi veya üstü
- Ekstra geniş ekranlarda mdpi veya üstü
[ 7.6 .1/A-2-3] Aşağıdaki yoğunluklardan herhangi birinin kullanılması durumunda çekirdek ve kullanıcı alanının kullanabileceği bellek en az 1280 MB OLMALIDIR:
- Küçük/normal ekranlarda 400 dpi veya üzeri
- Büyük ekranlarda xhdpi veya üstü
- Ekstra geniş ekranlarda tvdpi veya üzeri
[ 7.6 .1/A-2-4] Aşağıdaki yoğunluklardan herhangi birinin kullanılması durumunda çekirdek ve kullanıcı alanının kullanabileceği bellek en az 1824 MB OLMALIDIR:
- Küçük/normal ekranlarda 560dpi veya üzeri
- Büyük ekranlarda 400 dpi veya daha yüksek
- Ekstra geniş ekranlarda xhdpi veya üstü
Yukarıdaki "çekirdek ve kullanıcı alanı tarafından kullanılabilen bellek" ifadesinin, aygıt uygulamalarında çekirdeğin kontrolü altında olmayan radyo, video vb. donanım bileşenlerine halihazırda ayrılmış herhangi bir belleğe ek olarak sağlanan bellek alanını ifade ettiğini unutmayın.
Otomotiv cihaz uygulamaları:
- [ 7.7 .1/A] Çevresel modu destekleyen bir USB bağlantı noktası içermelidir.
Otomotiv cihaz uygulamaları:
- [ 7.8 .1/A-0-1] Bir mikrofon içermesi ZORUNLUDUR.
Otomotiv cihaz uygulamaları:
- [ 7.8 .2/A-0-1] Bir ses çıkışına sahip olmalı ve
android.hardware.audio.output
olarak bildirilmelidir.
2.5.2. Multimedya
Otomotiv cihaz uygulamalarının aşağıdaki ses kodlama ve kod çözme formatlarını desteklemesi ve bunları üçüncü taraf uygulamaların kullanımına sunması ZORUNLUDUR:
- [ 5.1 /A-0-1] MPEG-4 AAC Profili (AAC LC)
- [ 5.1 /A-0-2] MPEG-4 HE AAC Profili (AAC+)
- [ 5.1 /A-0-3] AAC ELD (geliştirilmiş düşük gecikmeli AAC)
Otomotiv cihaz uygulamalarının aşağıdaki video kodlama formatlarını desteklemesi ve bunları üçüncü taraf uygulamaların kullanımına sunması ZORUNLUDUR:
Otomotiv cihaz uygulamalarının aşağıdaki video kod çözme formatlarını desteklemesi ve bunları üçüncü taraf uygulamaların kullanımına sunması ZORUNLUDUR:
Otomotiv cihaz uygulamalarının aşağıdaki video kod çözmeyi desteklemesi KESİNLİKLE TAVSİYE EDİLİR:
- [ 5.3 /A-SR-1] H.265 HEVC
2.5.3. Yazılım
Otomotiv cihaz uygulamaları:
[ 3 /A-0-1]
android.hardware.type.automotive
özelliğini bildirmeniz ZORUNLUDUR.[ 3 /A-0-2] uiMode =
UI_MODE_TYPE_CAR
desteklemelidir ZORUNLU.[ 3 /A-0-3]
android.car.*
ad alanındaki tüm genel API'leri desteklemelidir ZORUNLU.
Otomotiv cihaz uygulamaları android.car.CarPropertyManager
android.car.VehiclePropertyIds
ile kullanan özel bir API sağlıyorsa, bunlar:
- [ 3 /A-1-1] Sistem uygulamasının bu özellikleri kullanımına özel ayrıcalıklar EKLENMEMELİ veya üçüncü taraf uygulamaların bu özellikleri kullanmasını engellememelidir.
- [ 3 /A-1-2] SDK'da zaten mevcut olan bir araç özelliğini ÇOĞALTMAMALIDIR.
Otomotiv cihaz uygulamaları:
[ 3.2 .1/A-0-1] Otomotiv İzni referans sayfasında belgelendiği gibi tüm izin sabitlerini desteklemeli ve uygulamalıdır ZORUNLU.
[ 3.2.3.1 /A-0-1] Burada listelenen aşağıdaki uygulama amaçları tarafından tanımlanan tüm genel amaç filtre modelleri için bir veya daha fazla uygulamayı veya hizmet bileşenini bir amaç işleyiciyle önceden yüklemesi ZORUNLUDUR.
[ 3.4 .1/A-0-1]
android.webkit.Webview
API'sinin eksiksiz bir uygulamasını SAĞLAMALIDIR.[ 3.8 .3/A-0-1] Üçüncü taraf uygulamalar tarafından talep edildiğinde
Notification.CarExtender
API'sini kullanan bildirimlerin GÖRÜNTÜLENMESİ ZORUNLUDUR.[ 3.8 .4/A-SR-1] Destek eylemini gerçekleştirecek bir asistanın cihaza uygulanması KESİNLİKLE TAVSİYE EDİLİR.
Otomotiv cihaz uygulamaları bas-konuş düğmesi içeriyorsa:
- [ 3.8 .4/A-1-1] Kullanıcı tarafından seçilen destek uygulamasını, başka bir deyişle
VoiceInteractionService
uygulayan uygulamayı başlatmak için belirlenmiş etkileşim olarak bas-konuş düğmesine kısa bir basış kullanılması ZORUNLUDUR.
Otomotiv cihaz uygulamaları:
- [ 3.8.3.1 /A-0-1]
Notifications on Automotive OS
açıklandığı gibi kaynakları doğru bir şekilde İŞLEMELİDİR. - [ 3.8.3.1 /A-0-2] Bildirim eylemleri için
Notification.Builder.addAction()
aracılığıyla sağlananların yerine PLAY ve MUTE öğelerinin görüntülenmesi ZORUNLUDUR. - [ 3.8.3.1 /A] Bildirim kanalı başına kontroller gibi zengin yönetim görevlerinin kullanımını kısıtlamalıdır GEREKLİ. Kontrolleri azaltmak için uygulama başına kullanıcı arayüzü olanaklarını KULLANABİLİR.
Otomotiv cihaz uygulamaları Kullanıcı HAL özelliklerini destekliyorsa:
- [ 3.9.3 /A-1-1] Tüm Kullanıcı yaşam döngüsü özelliklerinin uygulanması ZORUNLUDUR
-
INITIAL_USER_INFO
,SWITCH_USER
,CREATE_USER
,REMOVE_USER
.
-
Otomotiv cihaz uygulamaları:
- [ 3.14 /A-0-1] Bölüm 3.14'te açıklandığı gibi medya API'lerini kullanan üçüncü taraf uygulamaları desteklemek için bir kullanıcı arayüzü çerçevesi içermelidir ZORUNLU.
- [ 3.14 /A-0-2] Kullanıcının sürüş sırasında Medya Uygulamaları ile güvenli bir şekilde etkileşime girmesine izin vermelidir ZORUNLU.
- [ 3.14 /A-0-3]
CAR_INTENT_ACTION_MEDIA_TEMPLATE
örtülü Intent eyleminiCAR_EXTRA_MEDIA_PACKAGE
ekstrasıyla desteklemesi ZORUNLUDUR. - [ 3.14 /A-0-4] Bir Medya Uygulamasının tercih etkinliğinde gezinmek için bir olanak sağlamalıdır ZORUNLU, ancak bunu yalnızca Araç UX Kısıtlamaları geçerli olmadığında etkinleştirmesi GEREKİR.
- [ 3.14 /A-0-5] Medya Uygulamaları tarafından belirlenen hata mesajlarını görüntülemesi ZORUNLU ve isteğe bağlı
ERROR_RESOLUTION_ACTION_LABEL
veERROR_RESOLUTION_ACTION_INTENT
ekstralarını desteklemesi ZORUNLU. - [ 3.14 /A-0-6] Aramayı destekleyen uygulamalar için uygulama içi arama olanağını desteklemesi ZORUNLUDUR.
- [ 3.14 /A-0-7] MediaBrowser hiyerarşisini görüntülerken
CONTENT_STYLE_BROWSABLE_HINT
veCONTENT_STYLE_PLAYABLE_HINT
tanımlarına uyması ZORUNLUDUR.
Otomotiv cihaz uygulamaları varsayılan bir başlatıcı uygulaması içeriyorsa:
- [ 3.14 /A-1-1] Medya hizmetlerini içermesi ve bunları
CAR_INTENT_ACTION_MEDIA_TEMPLATE
amacı ile açması ZORUNLUDUR.
Otomotiv cihaz uygulamaları:
- [ 3.8 /A]
immersive documentation
açıklandığı gibi uygulama isteklerinin tam ekran moduna girmelerini kısıtlayabilir. - [ 3.8 /A] Durum çubuğunu ve gezinme çubuğunu her zaman görünür tutabilir.
- [ 3.8 /A] Bu öğelerin her zaman açıkça görülebilmesini sağlamak için, sistem kullanıcı arayüzü öğelerinin arkasındaki renkleri değiştirmeye yönelik uygulama isteklerini kısıtlayabilir.
2.5.4. Performans ve Güç
Otomotiv cihaz uygulamaları:
- [ 8.2 /A-0-1] İstatistiklerin Sistem API'si
android.car.storagemonitoring.CarStorageMonitoringManager
aracılığıyla geliştiricilere sunulması için her işlemin UID'si başına kalıcı depolamaya okunan ve yazılan bayt sayısını bildirmesi GEREKLİdir. Android Açık Kaynak Projesi, gereksinimiuid_sys_stats
çekirdek modülü aracılığıyla karşılar. - [ 8.3 /A-1-3] Garaj Modunu desteklemelidir.
- [ 8.3 /A] Aşağıdaki durumlar dışında her sürüşten sonra en az 15 dakika Garaj Modunda OLMALIDIR:
- Pil boşalmıştır.
- Boşta kalan işler planlanmamıştır.
- Sürücü Garaj Modundan çıkar.
- [ 8.4 /A-0-1] Android Açık Kaynak Projesi sitesinde belgelendiği gibi, her donanım bileşeni için geçerli tüketim değerini ve bileşenlerin zaman içinde neden olduğu yaklaşık pil tüketimini tanımlayan bileşen başına bir güç profili SAĞLAMALIDIR.
- [ 8.4 /A-0-2] Tüm güç tüketimi değerleri miliamper saat (mAh) cinsinden bildirilmelidir ZORUNLU.
- [ 8.4 /A-0-3] Her işlemin UID'sine göre CPU güç tüketimini rapor etmesi ZORUNLUDUR. Android Açık Kaynak Projesi, gereksinimi
uid_cputime
çekirdek modülü uygulaması aracılığıyla karşılar. - [ 8.4 /A] Donanım bileşeni güç kullanımını bir uygulamaya bağlayamıyorsanız, donanım bileşeninin kendisine atfedilmesi GEREKLİDİR.
- [ 8.4 /A-0-4] Bu güç kullanımını, uygulama geliştiricisinin
adb shell dumpsys batterystats
kabuk komutu aracılığıyla kullanılabilir hale getirmesi ZORUNLUDUR.
2.5.5. Güvenlik Modeli
Otomotiv cihaz uygulamaları birden fazla kullanıcıyı destekliyorsa:
- [ 9.5 /A-1-1] Cihaz yetkilendirmesi dışında kullanıcıların Başsız Sistem Kullanıcısıyla etkileşimde bulunmasına veya bu Kullanıcıya geçiş yapmasına izin VERMEMELİDİR.
- [ 9.5 /A-1-2]
BOOT_COMPLETED
öncesinde İkincil Kullanıcıya geçilmesi ZORUNLUDUR. - [ 9.5 /A-1-3] Bir cihazdaki maksimum Kullanıcı sayısına ulaşıldığında bile Konuk Kullanıcı oluşturma özelliğini desteklemesi ZORUNLUDUR.
Otomotiv cihaz uygulamaları:
- [ 9.11 /A-0-1] Anahtar deposu uygulamasının yalıtılmış bir yürütme ortamıyla YEDEKLENMESİ ZORUNLUDUR.
- [ 9.11 /A-0-2] Android Anahtar Deposu sisteminin desteklenen algoritmalarını güvenli bir şekilde izole edilmiş bir alanda düzgün bir şekilde desteklemek için RSA, AES, ECDSA ve HMAC şifreleme algoritmalarının ve MD5, SHA1 ve SHA-2 ailesi karma işlevlerinin uygulamalarına sahip olması ZORUNLUDUR çekirdek ve üzeri üzerinde çalışan koddan. Güvenli izolasyon, çekirdek veya kullanıcı alanı kodunun, DMA dahil, izole edilmiş ortamın dahili durumuna erişebileceği tüm potansiyel mekanizmaları ENGELLEMELİDİR. Yukarı akışlı Android Açık Kaynak Projesi (AOSP), Trusty uygulamasını kullanarak bu gereksinimi karşılar, ancak başka bir ARM TrustZone tabanlı çözüm veya uygun bir hipervizör tabanlı izolasyonun üçüncü taraflarca gözden geçirilmiş güvenli uygulaması alternatif seçeneklerdir.
- [ 9.11 /A-0-3] Kilit ekranı kimlik doğrulamasını yalıtılmış yürütme ortamında gerçekleştirmeli ve yalnızca başarılı olduğunda kimlik doğrulamaya bağlı anahtarların kullanılmasına izin vermelidir. Kilit ekranı kimlik bilgileri, yalnızca yalıtılmış yürütme ortamının kilit ekranı kimlik doğrulamasını gerçekleştirmesine izin verecek şekilde saklanmalıdır *ZORUNLU*. Yukarı akışlı Android Açık Kaynak Projesi, bu gereksinimi karşılamak için kullanılabilecek Gatekeeper Donanım Soyutlama Katmanı (HAL) ve Trusty'yi sağlar.
- [ 9.11 /A-0-4] Onay imzalama anahtarının güvenli donanım tarafından korunduğu ve imzalamanın güvenli donanımda gerçekleştirildiği anahtar doğrulamayı desteklemelidir ZORUNLU. Anahtarların cihaz tanımlayıcıları olarak kullanılmasını önlemek için, doğrulama imzalama anahtarlarının yeterli sayıda cihaz arasında paylaşılması ZORUNLUDUR. Bu gereksinimi karşılamanın bir yolu, belirli bir SKU'dan en az 100.000 birim üretilmediği sürece aynı doğrulama anahtarını paylaşmaktır. Bir SKU'nun 100.000 biriminden fazla üretilmesi durumunda her 100.000 birim için farklı bir anahtar KULLANILABİLİR.
- [9/A-0-1] 'android.hardware.security.model.uyumlu' özelliğinin bildirilmesi ZORUNLUDUR.
Bir cihaz uygulaması daha önceki bir Android sürümünde zaten başlatılmışsa, bu tür bir cihazın, yalıtılmış bir yürütme ortamı tarafından desteklenen bir anahtar deposuna sahip olma ve android.hardware.fingerprint
doğrulamayı destekleme gerekliliğinden muaf tutulacağını unutmayın; yalıtılmış bir yürütme ortamı tarafından desteklenen bir anahtar deposu gerektirir.
Otomotiv cihaz uygulamaları:
- [ 9.14 /A-0-1] Android çerçeve araç alt sistemlerinden gelen mesajların geçidi tutulması ZORUNLUDUR; örneğin, izin verilen mesaj türlerini ve mesaj kaynaklarını izin verilenler listesine eklemek.
- [ 9.14 /A-0-2] Android çerçevesinden veya üçüncü taraf uygulamalarından gelen hizmet reddi saldırılarına karşı izlenmelidir. Bu, araç alt sistemlerinin arızalanmasına neden olabilecek şekilde araç ağını trafikle dolduran kötü amaçlı yazılımlara karşı koruma sağlar.
2.5.6. Geliştirici Araçları ve Seçenekleri Uyumluluğu
Otomotiv cihaz uygulamaları:
- mükemmel
- [ 6.1 /A-0-1] Kabuk kullanıcısına, perfetto belgelerine uygun olan cmdline'ın bir
/system/bin/perfetto
ikili dosyasını sunması GEREKİR. - [ 6.1 /A-0-2] Perfetto ikilisi , perfetto belgelerinde tanımlanan şemaya uygun bir protobuf yapılandırmasını giriş olarak kabul etmelidir ZORUNLU.
- [ 6.1 /A-0-3] Perfetto ikilisinin , perfetto belgelerinde tanımlanan şemaya uygun bir protobuf izini çıktı olarak yazması ZORUNLUDUR.
- [ 6.1 /A-0-4] Perfetto ikili dosyası aracılığıyla en azından perfetto belgelerinde açıklanan veri kaynaklarını SAĞLAMALIDIR.
- [ 6.1 /A-0-1] Kabuk kullanıcısına, perfetto belgelerine uygun olan cmdline'ın bir
2.6. Tablet Gereksinimleri
Android Tablet cihazı, genellikle aşağıdaki kriterlerin tümünü karşılayan bir Android cihaz uygulamasını ifade eder:
- Her iki elle tutularak kullanılır.
- Kapaklı veya dönüştürülebilir bir konfigürasyona sahip değildir.
- Cihazda kullanılan fiziksel klavye uygulamaları standart bir bağlantı (örn. USB, Bluetooth) aracılığıyla bağlanır.
- Pil gibi hareket kabiliyeti sağlayan bir güç kaynağına sahiptir.
- Çapraz olarak ölçüldüğünde 7 inçten büyük ve 18 inçten küçük ekran boyutuna sahiptir.
Tablet cihaz uygulamaları, el tipi cihaz uygulamalarına benzer gereksinimlere sahiptir. İstisnalar bu bölümde * ile belirtilmiş ve bu bölümde referans olarak belirtilmiştir.
2.6.1. Donanım
Jiroskop
Tablet cihaz uygulamaları 3 eksenli bir jiroskop içeriyorsa:
- [ 7.3 .4/Tab-1-1] Saniyede 1000 dereceye kadar yönelim değişikliklerini ölçebilme yeteneğine sahip OLMALIDIR.
Minimum Bellek ve Depolama (Bölüm 7.6.1)
Elde taşınan gereksinimlerde küçük/normal ekranlar için listelenen ekran yoğunlukları tabletler için geçerli değildir.
USB çevre birimi modu (Bölüm 7.7.1)
Tablet cihaz uygulamaları çevre birimi modunu destekleyen bir USB bağlantı noktası içeriyorsa:
- [ 7.7.1 /Tab] Android Açık Aksesuar (AOA) API'sini UYGULAYABİLİR.
Sanal Gerçeklik Modu (Bölüm 7.9.1)
Sanal Gerçeklik Yüksek Performansı (Bölüm 7.9.2)
Sanal gerçeklik gereklilikleri tabletler için geçerli değildir.
2.6.2. Güvenlik Modeli
Anahtarlar ve Kimlik Bilgileri (Bölüm 9.11)
Bölüm [ 9.11 ]'e bakın.
Tablet cihaz uygulamaları birden fazla kullanıcı içeriyorsa ve android.hardware.telephony
özellik işaretini bildirmiyorsa, bunlar:
- [ 9.5 /T-1-1] Cihaz sahiplerinin cihazdaki ek kullanıcıları ve onların yeteneklerini yönetmesine olanak tanıyan bir özellik olan kısıtlı profilleri desteklemesi ZORUNLUDUR. Kısıtlanmış profiller sayesinde cihaz sahipleri, ek kullanıcıların çalışabileceği ayrı ortamları hızlı bir şekilde oluşturabilir ve bu ortamlarda bulunan uygulamalardaki daha ayrıntılı kısıtlamaları yönetebilir.
Tablet cihaz uygulamaları birden fazla kullanıcı içeriyorsa ve android.hardware.telephony
özellik işaretini bildiriyorsa, bunlar:
- [ 9.5 /T-2-1] Kısıtlanmış profilleri DESTEKLEMEMELİDİR ancak diğer kullanıcıların sesli aramalara ve SMS'e erişimini etkinleştirmek/devre dışı bırakmak için AOSP kontrol uygulamasıyla uyumlu OLMALIDIR.
2.6.2. Yazılım
- [ 3.2.3.1 /Tab-0-1] Burada listelenen aşağıdaki uygulama amaçları tarafından tanımlanan tüm genel amaç filtre modelleri için bir veya daha fazla uygulamayı veya hizmet bileşenini bir amaç işleyiciyle önceden yüklemesi ZORUNLUDUR.
3. Yazılım
3.1. Yönetilen API Uyumluluğu
Yönetilen Dalvik bayt kodu yürütme ortamı, Android uygulamaları için birincil araçtır. Android uygulama programlama arayüzü (API), yönetilen çalışma zamanı ortamında çalışan uygulamalara sunulan Android platformu arayüzleri kümesidir.
Cihaz uygulamaları:
[C-0-1] Android SDK tarafından kullanıma sunulan herhangi bir belgelenmiş API'nin veya yukarı akış Android kaynak kodunda "@SystemApi" işaretçisiyle süslenmiş herhangi bir API'nin tüm belgelenmiş davranışları da dahil olmak üzere eksiksiz uygulamalarını SAĞLAMALIDIR.
[C-0-2] TestApi ek açıklamasıyla (@TestApi) işaretlenen tüm sınıfları, yöntemleri ve ilgili öğeleri desteklemeli/korumalı ZORUNLU.
[C-0-3] Bu Uyumluluk Tanımında özellikle izin verilen durumlar dışında, yönetilen API'leri atlamamalı, API arayüzlerini veya imzalarını değiştirmemeli, belgelenen davranıştan sapmamalı veya işlem yapılmayan işlemleri içermemelidir.
[C-0-4] Android'in API'leri içerdiği bazı donanım özellikleri çıkarıldığında bile API'leri mevcut tutmalı ve makul bir şekilde davranmalıdır ZORUNLU. Bu senaryoya özel gereksinimler için bölüm 7'ye bakın.
[C-0-5] Üçüncü taraf uygulamaların, AOSP'de önyükleme sınıf yolunda bulunan ve Java dil paketlerindeki yöntemler ve alanlar olarak tanımlanan ve Java'nın bir parçasını oluşturmayan SDK olmayan arayüzleri kullanmasına izin VERMEMELİDİR. genel SDK'dır. Bu, SDK belgelerinde ve özel ve paket-özel sınıf üyelerinde açıklandığı gibi,
@hide
ek açıklamasıyla süslenmiş ancak@SystemAPI
ile süslenmemiş API'leri içerir.[C-0-6] SDK olmayan tüm arayüzlerin, uygun API seviyesi şubesi için
prebuilts/runtime/appcompat/hiddenapi-flags.csv
yolundaki geçici ve reddedilen liste işaretleri aracılığıyla sağlanan aynı kısıtlı listelerde yer alması ZORUNLUDUR. AOSP.[C-0-7] AOSP'de bulunan mevcut ortak anahtarları kullanarak imzalı yapılandırmayı herhangi bir APK'ya yerleştirerek SDK olmayan arayüzleri kısıtlı bir listeden kaldırmak için imzalı yapılandırma dinamik güncelleme mekanizmasını desteklemelidir ZORUNLU.
Ancak onlar:
- MAYIS, eğer gizli bir API yoksa veya cihaz uygulamasında farklı şekilde uygulanmışsa, gizli API'yi red listesine taşıyın veya tüm kısıtlı listelerden çıkarın.
- MAYIS, eğer AOSP'de gizli bir API mevcut değilse, gizli API'yi kısıtlı listelerden herhangi birine ekleyebilirsiniz.
3.1.1. Android Uzantıları
Android, belirli bir API düzeyinin uzantı sürümünü güncelleyerek o API düzeyinin yönetilen API yüzeyinin genişletilmesini destekler. android.os.ext.SdkExtensions.getExtensionVersion(int apiLevel)
API, eğer söz konusu API düzeyi için uzantılar varsa, sağlanan apiLevel
uzantı sürümünü döndürür.
Android cihaz uygulamaları:
[C-0-1] Hem
ExtShared
paylaşılan kütüphanesinin hem deExtServices
hizmetlerinin AOSP uygulamasını, her API düzeyi için izin verilen minimum sürümlerden daha büyük veya bu sürümlere eşit sürümlerle önceden yüklemesi ZORUNLUDUR. Örneğin, API düzeyi 24'ü çalıştıran Android 7.0 cihaz uygulamalarının en az sürüm 1'i içermesi ZORUNLUDUR.[C-0-2] Yalnızca AOSP tarafından tanımlanan geçerli uzantı sürüm numarasını döndürmelidir ZORUNLU.
[C-0-3] bölüm 3.1'deki gereksinimlere uygun olarak, diğer yönetilen API'lerin desteklendiği şekilde
android.os.ext.SdkExtensions.getExtensionVersion(int apiLevel)
tarafından döndürülen uzantı sürümleri tarafından tanımlanan tüm API'leri desteklemelidir ZORUNLU.
3.1.2. Android Kitaplığı
Apache HTTP istemcisinin kullanımdan kaldırılması nedeniyle cihaz uygulamaları:
- [C-0-1]
org.apache.http.legacy
kitaplığını önyükleme sınıfı yoluna YERLEŞTİRMEMELİDİR. - [C-0-2]
org.apache.http.legacy
kitaplığını yalnızca uygulama aşağıdaki koşullardan birini karşıladığında uygulama sınıf yoluna EKLEMELİDİR:- API düzeyi 28 veya daha düşükünü hedefler.
- Bildiriminde,
<uses-library>
öğesininandroid:name
niteliğiniorg.apache.http.legacy
olarak ayarlayarak kitaplığa ihtiyaç duyduğunu bildirir.
AOSP uygulaması bu gereksinimleri karşılar.
3.2. Yazılım API Uyumluluğu
Bölüm 3.1'deki yönetilen API'lere ek olarak Android ayrıca, uygulama derleme zamanında uygulanamayan Android uygulamalarının amaçları, izinleri ve benzer yönleri gibi önemli bir yalnızca çalışma zamanına yönelik "yumuşak" API içerir.
3.2.1. İzinler
- [C-0-1] Cihaz uygulayıcılarının , İzin referans sayfasında belgelendiği şekilde tüm izin sabitlerini desteklemesi ve uygulaması ZORUNLUDUR. Bölüm 9'un Android güvenlik modeliyle ilgili ek gereksinimleri listelediğini unutmayın.
3.2.2. Parametreleri Oluştur
Android API'leri, android.os.Build sınıfında mevcut cihazı tanımlaması amaçlanan bir dizi sabit içerir.
- [C-0-1] Cihaz uygulamalarında tutarlı, anlamlı değerler sağlamak için aşağıdaki tablo, cihaz uygulamalarının uyması GEREKEN bu değerlerin formatlarına ilişkin ek kısıtlamalar içermektedir.
Parametre | Detaylar |
---|---|
VERSİYON.REEASE | Şu anda çalışmakta olan Android sisteminin insan tarafından okunabilir biçimdeki sürümü. Bu alanın Android 12 için İzin Verilen Sürüm Dizgileri bölümünde tanımlanan dize değerlerinden birine sahip olması ZORUNLUDUR. |
VERSION.SDK | Şu anda çalışmakta olan Android sisteminin, üçüncü taraf uygulama kodunun erişebileceği bir biçimdeki sürümü. Android 12 için bu alanın 12_INT tamsayı değerine sahip olması ZORUNLUDUR. |
VERSION.SDK_INT | Şu anda çalışmakta olan Android sisteminin, üçüncü taraf uygulama kodunun erişebileceği bir biçimdeki sürümü. Android 12 için bu alanın 12_INT tamsayı değerine sahip olması ZORUNLUDUR. |
SÜRÜM.ARTIMLI | Cihaz uygulayıcısı tarafından seçilen ve halihazırda çalışmakta olan Android sisteminin belirli yapısını insan tarafından okunabilir biçimde belirten bir değer. Bu değer, son kullanıcılara sunulan farklı yapılar için yeniden KULLANILMAMALIDIR. Bu alanın tipik bir kullanımı, yapıyı oluşturmak için hangi yapı numarasının veya kaynak kontrol değişikliği tanımlayıcısının kullanıldığını belirtmektir. Bu alanın değeri yazdırılabilir 7 bit ASCII olarak kodlanabilir ve "^[^ :\/~]+$" normal ifadesiyle eşleşmelidir ZORUNLU. |
PANO | Cihaz tarafından kullanılan belirli dahili donanımı tanımlayan, cihaz uygulayıcısı tarafından seçilen, insan tarafından okunabilir formatta bir değer. Bu alanın olası bir kullanımı, cihaza güç veren kartın özel revizyonunu belirtmektir. Bu alanın değeri 7 bit ASCII olarak kodlanabilir ve "^[a-zA-Z0-9_-]+$" normal ifadesiyle eşleşmelidir ZORUNLU. |
MARKA | Son kullanıcılar tarafından bilinen, cihazla ilişkili marka adını yansıtan bir değer. İnsan tarafından okunabilir formatta OLMALIDIR ve cihazın üreticisini veya cihazın pazarlandığı şirket markasını temsil etmelidir. Bu alanın değeri 7 bit ASCII olarak kodlanabilir ve "^[a-zA-Z0-9_-]+$" normal ifadesiyle eşleşmelidir ZORUNLU. |
DESTEKLENEN_ABIS | Yerel kodun talimat setinin adı (CPU türü + ABI kuralı). Bkz. bölüm 3.3. Yerel API Uyumluluğu |
SUPPORTED_32_BIT_ABIS | Yerel kodun talimat setinin adı (CPU türü + ABI kuralı). Bkz. bölüm 3.3. Yerel API Uyumluluğu |
SUPPORTED_64_BIT_ABIS | Yerel kodun ikinci komut kümesinin adı (CPU türü + ABI kuralı). Bkz. bölüm 3.3. Yerel API Uyumluluğu |
CPU_ABI | Yerel kodun talimat setinin adı (CPU türü + ABI kuralı). Bkz. bölüm 3.3. Yerel API Uyumluluğu |
CPU_ABI2 | Yerel kodun ikinci komut kümesinin adı (CPU türü + ABI kuralı). Bkz. bölüm 3.3. Yerel API Uyumluluğu |
CİHAZ | Cihazın donanım özelliklerinin konfigürasyonunu ve endüstriyel tasarımını tanımlayan geliştirme adını veya kod adını içeren, cihaz uygulayıcısı tarafından seçilen bir değer. Bu alanın değeri 7 bit ASCII olarak kodlanabilir ve "^[a-zA-Z0-9_-]+$" normal ifadesiyle eşleşmelidir ZORUNLU. Bu cihaz adı ürünün kullanım ömrü boyunca DEĞİŞMEMELİDİR. |
PARMAK İZİ | Bu yapıyı benzersiz şekilde tanımlayan bir dize. Makul düzeyde insan tarafından okunabilir OLMALIDIR. Bu şablona uyması GEREKİR: $(MARKA)/$(ÜRÜN)/ Örneğin: acme/ürünüm/ Parmak izi boşluk karakterleri İÇERMEMELİDİR. Bu alanın değeri 7 bitlik ASCII olarak kodlanabilir OLMALIDIR. |
DONANIM | Donanımın adı (çekirdek komut satırından veya /proc'tan). Makul düzeyde insan tarafından okunabilir OLMALIDIR. Bu alanın değeri 7 bit ASCII olarak kodlanabilir ve "^[a-zA-Z0-9_-]+$" normal ifadesiyle eşleşmelidir ZORUNLU. |
EV SAHİBİ | Derlemenin oluşturulduğu ana bilgisayarı, insanlar tarafından okunabilir biçimde benzersiz şekilde tanımlayan bir dize. Bu alanın spesifik formatına ilişkin herhangi bir gereklilik yoktur, ancak boş veya boş dize ("") OLMAMALIDIR. |
İD | Cihaz uygulayıcısı tarafından belirli bir yayına atıfta bulunmak üzere seçilen, insan tarafından okunabilir formatta bir tanımlayıcı. Bu alan android.os.Build.VERSION.INCREMENTAL ile aynı olabilir, ancak son kullanıcıların yazılım yapıları arasında ayrım yapması için yeterince anlamlı bir değer OLMALIDIR. Bu alanın değeri 7 bit ASCII olarak kodlanabilir ve "^[a-zA-Z0-9._-]+$" normal ifadesiyle eşleşmelidir ZORUNLU. |
ÜRETİCİ FİRMA | Ürünün Orijinal Ekipman Üreticisinin (OEM) ticari adı. Bu alanın spesifik formatına ilişkin herhangi bir gereklilik yoktur, ancak boş veya boş dize ("") OLMAMALIDIR. Bu alan ürünün kullanım ömrü boyunca DEĞİŞMEMELİDİR. |
SOC_MANUFACTURER | Üründe kullanılan çip üzerindeki birincil sistemin (SOC) üreticisinin ticari adı. Aynı SOC üreticisine sahip cihazlar aynı sabit değeri kullanmalıdır. Lütfen kullanılacak doğru sabiti SOC üreticisine sorun. Bu alanın değeri 7 bit ASCII olarak kodlanabilir OLMALIDIR, "^([0-9A-Za-z ]+)" normal ifadesiyle eşleşmelidir ZORUNLU, boşlukla başlamamalı veya bitmemeli ve "'ye eşit OLMAMALIDIR" Bilinmeyen". Bu alan ürünün kullanım ömrü boyunca DEĞİŞMEMELİDİR. |
SOC_MODEL | Üründe kullanılan çipteki (SOC) birincil sistemin model adı. Aynı SOC modeline sahip cihazlar aynı sabit değeri kullanmalıdır. Lütfen kullanılacak doğru sabiti SOC üreticisine sorun. Bu alanın değeri 7 bit ASCII olarak kodlanabilir olmalı ve "^([0-9A-Za-z ._/+-]+)$" normal ifadesiyle eşleşmelidir, boşlukla başlamamalı veya bitmemelidir ve ZORUNLUDUR “Bilinmeyen”e eşit OLMAYIN. Bu alan ürünün kullanım ömrü boyunca DEĞİŞMEMELİDİR. |
MODELİ | Cihaz uygulayıcısı tarafından seçilen ve son kullanıcının bildiği cihazın adını içeren bir değer. Bu, cihazın pazarlandığı ve son kullanıcılara satıldığı adla aynı OLMALIDIR. Bu alanın spesifik formatına ilişkin herhangi bir gereklilik yoktur, ancak boş veya boş dize ("") OLMAMALIDIR. Bu alan ürünün kullanım ömrü boyunca DEĞİŞMEMELİDİR. |
ÜRÜN | Cihaz uygulayıcısı tarafından seçilen ve aynı marka içinde benzersiz olması gereken belirli bir ürünün (SKU) geliştirme adını veya kod adını içeren bir değer. İnsan tarafından okunabilir OLMALIDIR ancak son kullanıcıların görüntülemesi amaçlanmamıştır. Bu alanın değeri 7 bit ASCII olarak kodlanabilir ve "^[a-zA-Z0-9_-]+$" normal ifadesiyle eşleşmelidir ZORUNLU. Bu ürün adı, ürünün kullanım ömrü boyunca DEĞİŞMEMELİDİR. |
ODM_SKU | Cihazın belirli yapılandırmalarını (örneğin, satıldığında cihaza dahil olan çevre birimleri) takip etmek için kullanılan SKU'yu (Stok Saklama Birimi) içeren, cihaz uygulayıcısı tarafından seçilen isteğe bağlı bir değer. Bu alanın değeri 7 bit ASCII olarak kodlanabilir ve "[0-9A-Za-z.,_-])" normal ifadesiyle eşleşmelidir ZORUNLU |
SERİ | "BİLİNMİYOR" ifadesini döndürmesi GEREKİR. |
ETİKETLER | Yapıyı daha da ayırt eden, cihaz uygulayıcısı tarafından seçilen, virgülle ayrılmış etiket listesi. Etiketlerin 7 bit ASCII olarak kodlanabilir olması ve "^[a-zA-Z0-9._-]+" normal ifadesiyle eşleşmesi GEREKİR ve üç tipik Android platformu imzalama yapılandırmasına karşılık gelen değerlerden birine sahip olması ZORUNLUDUR: yayın- anahtarlar, geliştirme anahtarları ve test anahtarları. |
ZAMAN | Derlemenin gerçekleştiği zamanın zaman damgasını temsil eden bir değer. |
TİP | Yapının çalışma zamanı yapılandırmasını belirten, cihaz uygulayıcısı tarafından seçilen bir değer. Bu alanın üç tipik Android çalışma zamanı yapılandırmasına karşılık gelen değerlerden birine sahip olması ZORUNLUDUR: user, userdebug veya eng. |
KULLANICI | Derlemeyi oluşturan kullanıcının (veya otomatik kullanıcının) adı veya kullanıcı kimliği. Bu alanın spesifik formatına ilişkin herhangi bir gereklilik yoktur, ancak boş veya boş dize ("") OLMAMALIDIR. |
SECURITY_PATCH | Bir yapının güvenlik yaması düzeyini gösteren bir değer. Yapının, belirlenen Android Kamu Güvenliği Bülteni aracılığıyla açıklanan sorunlardan herhangi birine karşı hiçbir şekilde savunmasız olmadığını belirtmesi ZORUNLUDUR. [YYYY-AA-GG] biçiminde olması ve Android Kamu Güvenliği Bülteni veya Android Güvenlik Danışma Belgesi'nde belgelenen tanımlı bir dizeyle (örneğin, "2015-11-01") eşleşmesi GEREKİR. |
BASE_OS | Android Kamu Güvenliği Bülteni'nde sağlanan yamalar dışında bu yapıyla aynı olan yapının PARMAK İZİ parametresini temsil eden bir değer. Doğru değeri bildirmesi GEREKİR ve eğer böyle bir yapı yoksa boş bir dize ("") bildirin. |
ÖNYÜKLEYİCİ | Cihazda kullanılan belirli dahili önyükleyici sürümünü insan tarafından okunabilir biçimde tanımlayan, cihaz uygulayıcısı tarafından seçilen bir değer. Bu alanın değeri 7 bit ASCII olarak kodlanabilir ve "^[a-zA-Z0-9._-]+$" normal ifadesiyle eşleşmelidir ZORUNLU. |
getRadioVersion() | Cihazda kullanılan spesifik dahili radyo/modem versiyonunu tanımlayan, cihaz uygulayıcısı tarafından seçilen, insan tarafından okunabilir formatta bir değer OLMALIDIR (olmalı veya döndürmelidir). Bir aygıtın dahili radyosu/modemi yoksa NULL döndürmesi GEREKİR. Bu alanın değeri 7 bit ASCII olarak kodlanabilir ve "^[a-zA-Z0-9._-,]+$" normal ifadesiyle eşleşmelidir ZORUNLU. |
getSerial() | Aynı MODEL ve ÜRETİCİYE sahip cihazlarda mevcut ve benzersiz olması GEREKEN bir donanım seri numarası OLMALIDIR (olmalı veya döndürmelidir). Bu alanın değeri 7 bit ASCII olarak kodlanabilir ve "^[a-zA-Z0-9._-,]+$" normal ifadesiyle eşleşmelidir ZORUNLU. |
3.2.3. Amaç Uyumluluğu
3.2.3.1. Ortak Uygulama Amaçları
Android amaçları, uygulama bileşenlerinin diğer Android bileşenlerinden işlevsellik talep etmesine olanak tanır. Android yukarı akış projesi, ortak eylemleri gerçekleştirmek için çeşitli niyet modellerini uygulayan uygulamaların bir listesini içerir.
Cihaz uygulamaları:
- [C-SR-1] Burada listelenen aşağıdaki uygulama amaçları tarafından tanımlanan tüm genel amaç filtre modelleri için bir veya daha fazla uygulamayı veya hizmet bileşenini bir amaç işleyiciyle önceden yüklemeniz ve bunların yerine getirilmesini sağlamanız, yani bunlar için geliştiricinin beklentilerini karşılamanız KESİNLİKLE ÖNERİLİR SDK'da açıklandığı gibi ortak uygulama amaçları.
Her cihaz tipine ilişkin zorunlu uygulama amaçları için lütfen Bölüm 2'ye bakın.
3.2.3.2. Niyet Çözümü
[C-0-1] Android genişletilebilir bir platform olduğundan, cihaz uygulamalarının, Ayarlar hariç bölüm 3.2.3.1'de atıfta bulunulan her amaç modelinin üçüncü taraf uygulamalar tarafından geçersiz kılınmasına izin vermesi ZORUNLUDUR. Yukarı akışlı Android açık kaynak uygulaması buna varsayılan olarak izin verir.
[C-0-2] Cihaz uygulayıcıları, sistem uygulamalarının bu amaç kalıplarını kullanımına özel ayrıcalıklar VERMEMELİ veya üçüncü taraf uygulamaların bu kalıplara bağlanmasını ve bunların kontrolünü üstlenmesini engellememelidir. Bu yasak, özellikle, kullanıcının tümü aynı amaç modelini işleyen birden fazla uygulama arasında seçim yapmasına olanak tanıyan "Seçici" kullanıcı arayüzünün devre dışı bırakılmasını içerir ancak bununla sınırlı değildir.
[C-0-3] Cihaz uygulamalarının, kullanıcıların amaçlara yönelik varsayılan etkinliği değiştirebilmesi için bir kullanıcı arayüzü sağlaması ZORUNLUDUR.
Ancak, varsayılan etkinlik veri URI'si için daha spesifik bir özellik sağladığında, cihaz uygulamaları belirli URI kalıpları için (örneğin, http://play.google.com) varsayılan etkinlikler SAĞLAYABİLİR. Örneğin, "http://www.android.com" veri URI'sini belirten bir amaç filtresi modeli, tarayıcının "http://" için temel amaç modelinden daha spesifiktir.
Android ayrıca, üçüncü taraf uygulamaların belirli web URI amacı türleri için yetkili bir varsayılan uygulama bağlama davranışı bildirmesine yönelik bir mekanizma içerir. Bu tür yetkili bildirimler bir uygulamanın amaç filtresi modellerinde tanımlandığında, cihaz uygulamaları:
- [C-0-4] Yukarı akışlı Android Açık Kaynak Projesi'nde Paket Yöneticisi tarafından uygulanan Digital Asset Links spesifikasyonunda tanımlanan doğrulama adımlarını gerçekleştirerek herhangi bir amaç filtresini doğrulamaya ÇALIŞMALIDIR.
- [C-0-5] Uygulamanın kurulumu sırasında amaç filtrelerini doğrulamaya çalışmalı ve başarıyla doğrulanan tüm URI amaç filtrelerini, URI'leri için varsayılan uygulama işleyicileri olarak ayarlamalıdır.
- Başarılı bir şekilde doğrulanmaları ancak diğer aday URI filtrelerinin doğrulamada başarısız olması durumunda, belirli URI amaç filtrelerini URI'leri için varsayılan uygulama işleyicileri olarak ayarlayabilir. Bir cihaz uygulamasının bunu yapması durumunda, kullanıcıya ayarlar menüsünde URI başına uygun kalıp geçersiz kılmaları sağlaması ZORUNLUDUR.
- Kullanıcıya Ayarlar'da aşağıdaki şekilde uygulama başına Uygulama Bağlantıları kontrolleri SAĞLANMALIDIR:
- [C-0-6] Kullanıcının, bir uygulamanın varsayılan uygulama bağlantıları davranışını bütünsel olarak geçersiz kılabilmesi ZORUNLUDUR: her zaman açık, her zaman sor veya asla açılma; bu, tüm aday URI amaç filtrelerine eşit şekilde uygulanmalıdır.
- [C-0-7] Kullanıcının aday URI amaç filtrelerinin listesini görebilmesi GEREKİR.
- Cihaz uygulaması, kullanıcıya başarılı bir şekilde doğrulanan belirli aday URI amaç filtrelerini amaç başına filtre bazında geçersiz kılma yeteneği sağlayabilir.
- [C-0-8] Cihaz uygulaması, bazı aday URI amaç filtrelerinin doğrulamada başarılı olmasına, bazılarının ise başarısız olmasına izin veriyorsa, cihaz uygulamasının kullanıcılara belirli aday URI amaç filtrelerini görüntüleme ve geçersiz kılma yeteneğini sağlaması ZORUNLUDUR.
3.2.3.3. Amaç Ad Alanları
- [C-0-1] Cihaz uygulamaları, Android.* veya com.android.* ad alanında bir ACTION, CATEGORY veya başka bir anahtar dize kullanan herhangi bir yeni amacı veya yayın amacı modelini kabul eden herhangi bir Android bileşeni İÇERMEMELİDİR.
- [C-0-2] Cihaz uygulayıcıları, başka bir kuruluşa ait bir paket alanına bir EYLEM, KATEGORİ veya başka bir anahtar dize kullanan herhangi bir yeni amacı veya yayın amacı modelini kabul eden herhangi bir Android bileşenini EKLEMEMELİDİR.
- [C-0-3] Cihaz uygulayıcıları bölüm 3.2.3.1'de listelenen amaç modellerinden herhangi birini DEĞİŞTİRMEMELİ veya UZATMAMALIDIR.
- Cihaz uygulamaları, kendi kuruluşlarıyla açıkça ve açıkça ilişkilendirilen ad alanlarını kullanan amaç modellerini İÇEREBİLİR. Bu yasaklama, bölüm 3.6'da Java dil sınıfları için belirtilene benzerdir.
3.2.3.4. Yayın Amaçları
Üçüncü taraf uygulamalar, donanım veya yazılım ortamındaki değişiklikler hakkında kendilerini bilgilendirmek amacıyla belirli amaçları yayınlamak için platforma güvenir.
Cihaz uygulamaları:
- [C-0-1] SDK belgelerinde açıklandığı gibi uygun sistem olaylarına yanıt olarak burada listelenen genel yayın amaçlarını yayınlaması ZORUNLUDUR. Arka plan uygulamalarına yönelik sınırlamalar SDK belgelerinde de açıklandığı için bu gereksinimin bölüm 3.5 ile çelişmediğini unutmayın. Ayrıca belirli yayın amaçları donanım desteğine bağlıdır; eğer cihaz gerekli donanımı destekliyorsa amaçları yayınlamaları ve davranışı SDK belgeleriyle satır içi sağlamaları ZORUNLUDUR.
3.2.3.5. Koşullu Uygulama Amaçları
Android, kullanıcılara varsayılan uygulamalarını (örneğin Ana ekran veya SMS) seçmenin kolay bir yolunu sağlayan ayarlar içerir.
Mantıklı olduğu durumlarda, cihaz uygulamalarının benzer bir ayarlar menüsü sağlaması ve aşağıdaki SDK belgelerinde açıklanan amaç filtresi modeli ve API yöntemleriyle uyumlu olması ZORUNLUDUR.
Cihaz uygulamaları android.software.home_screen
raporunu veriyorsa:
- [C-1-1] Ana Ekran için varsayılan uygulama ayarları menüsünü gösterme
android.settings.HOME_SETTINGS
amacına uyması ZORUNLUDUR.
Cihaz uygulamaları android.hardware.telephony
raporunu veriyorsa:
[C-2-1] Varsayılan SMS uygulamasını değiştirmek için bir iletişim kutusu göstermek üzere
android.provider.Telephony.ACTION_CHANGE_DEFAULT
amacını çağıracak bir ayarlar menüsü SAĞLAMALIDIR.[C-2-2]
android.telecom.action.CHANGE_DEFAULT_DIALER
, kullanıcının varsayılan Telefon uygulamasını değiştirmesine izin verecek bir iletişim kutusu gösterme amacına uyması ZORUNLUDUR.- Önceden yüklenmiş Telefon uygulamasını kullanan acil aramalar hariç, gelen ve giden aramalar için kullanıcı tarafından seçilen varsayılan Telefon uygulamasının kullanıcı arayüzünü KULLANMALIDIR.
[C-2-3] android.telecom.action.CHANGE_PHONE_ACCOUNTS amacının, telekomünikasyon servis sağlayıcısının giden aramaları yapmak için kullanacağı varsayılan PhoneAccount'un yanı sıra,
PhoneAccounts
ilişkiliConnectionServices
yapılandırmak için kullanıcıya olanak sağlaması ZORUNLUDUR. AOSP uygulaması, "Çağrılar" ayarları menüsüne "Arama Hesapları seçeneği" menüsünü ekleyerek bu gereksinimi karşılar.[C-2-4]
android.app.role.CALL_REDIRECTION
rolünü taşıyan bir uygulama içinandroid.telecom.CallRedirectionService
izin verilmesi ZORUNLUDUR.[C-2-5] Kullanıcıya,
android.app.role.CALL_REDIRECTION
rolünü taşıyan bir uygulamayı seçme olanağını SAĞLAMALIDIR.[C-2-6] android.intent.action.SENDTO ve android.intent.action.VIEW amaçlarını dikkate almalı ve SMS mesajları göndermek/görüntülemek için bir etkinlik sağlamalıdır.
[C-SR-1] android.intent.action.ANSWER , android.intent.action.CALL , android.intent.action.CALL_BUTTON , android.intent.action.VIEW ve android.intent.action'a saygı gösterilmesi KESİNLİKLE TAVSİYE EDİLİR. DIAL amaçları, bu amaçları işleyebilen ve SDK'da açıklandığı şekilde yerine getirilmesini sağlayabilen, önceden yüklenmiş bir çevirici uygulamasına sahiptir.
Cihaz uygulamaları android.hardware.nfc.hce
raporunu veriyorsa:
- [C-3-1] Temassız ödeme için varsayılan uygulama ayarları menüsünü gösterme android.settings.NFC_PAYMENT_SETTINGS amacına uyması ZORUNLUDUR.
- [C-3-2] Android.nfc.cardemulation.action.ACTION_CHANGE_DEFAULT , kullanıcıdan SDK'da açıklandığı gibi belirli bir kategori için varsayılan kart emülasyon hizmetini değiştirmesini isteyen bir iletişim kutusu açan bir etkinlik gösterme niyetini dikkate almalıdır ZORUNLU.
Cihaz uygulamaları android.hardware.nfc
raporunu veriyorsa:
- [C-4-1] bu amaçlara ilişkin geliştirici beklentilerini karşılayan bir etkinliği göstermek için android.nfc.action.NDEF_DISCOVERED , android.nfc.action.TAG_DISCOVERED ve android.nfc.action.TECH_DISCOVERED amaçlarına uyması ZORUNLUDUR. SDK'dır.
Cihaz uygulamaları android.hardware.bluetooth
raporunu veriyorsa:
- [C-5-1] 'android.bluetooth.adapter.action.REQUEST_ENABLE' amacını dikkate almalı ve kullanıcının Bluetooth'u açmasına izin verecek bir sistem etkinliği göstermelidir ZORUNLU.
- [C-5-2] 'android.bluetooth.adapter.action.REQUEST_DISCOVERABLE' amacını dikkate almalı ve keşfedilebilir mod isteyen bir sistem etkinliği göstermelidir ZORUNLU.
Cihaz uygulamaları DND özelliğini destekliyorsa:
- [C-6-1]
ACTION_NOTIFICATION_POLICY_ACCESS_SETTINGS
amacına yanıt verecek bir etkinlik UYGULAMALIDIR; UI_MODE_TYPE_NORMAL ile uygulamalar için bu, kullanıcının uygulamaya DND politika yapılandırmalarına erişim izni verebileceği veya reddedebileceği bir etkinlik OLMALIDIR.
Cihaz uygulamaları kullanıcıların cihazda üçüncü taraf giriş yöntemlerini kullanmasına izin veriyorsa:
- [C-7-1]
android.settings.INPUT_METHOD_SETTINGS
amacına yanıt olarak üçüncü taraf giriş yöntemlerini eklemek ve yapılandırmak için kullanıcı tarafından erişilebilen bir mekanizma SAĞLAMALIDIR.
Cihaz uygulamaları üçüncü taraf erişilebilirlik hizmetlerini destekliyorsa:
- [C-8-1] önceden yüklenmiş erişilebilirlik hizmetlerinin yanı sıra üçüncü taraf erişilebilirlik hizmetlerini etkinleştirmek ve devre dışı bırakmak için kullanıcı tarafından erişilebilen bir mekanizma sağlamaya yönelik
android.settings.ACCESSIBILITY_SETTINGS
amacına uyulması ZORUNLUDUR.
Cihaz uygulamaları Wi-Fi Kolay Bağlantı desteğini içeriyorsa ve işlevsellik üçüncü taraf uygulamalara sunuluyorsa:
- [C-9-1] Settings#ACTION_PROCESS_WIFI_EASY_CONNECT_URI Intent API'lerini SDK belgelerinde açıklandığı şekilde UYGULAMALIDIR.
Cihaz uygulamaları veri tasarrufu modunu sağlıyorsa:
- [C-10-1] Ayarlarda,
Settings.ACTION_IGNORE_BACKGROUND_DATA_RESTRICTIONS_SETTINGS
amacını işleyen, kullanıcıların izin verilenler listesine uygulama eklemesine veya uygulamaları kaldırmasına olanak tanıyan bir kullanıcı arayüzü SAĞLAMALIDIR.
Cihaz uygulamaları veri tasarrufu modunu sağlamıyorsa:
- [C-11-1]
Settings.ACTION_IGNORE_BACKGROUND_DATA_RESTRICTIONS_SETTINGS
amacını işleyen bir etkinliğe sahip olması GEREKİR, ancak bunu işlem dışı olarak uygulayabilir.
Cihaz uygulamaları kamera desteğini android.hardware.camera.any
aracılığıyla bildirirse:
- [C-12-3] Yalnızca önceden yüklenmiş Android uygulamalarının , SDK belgesinde açıklandığı şekilde
MediaStore.ACTION_IMAGE_CAPTURE
,MediaStore.ACTION_IMAGE_CAPTURE_SECURE
veMediaStore.ACTION_VIDEO_CAPTURE
amaçlarını işlemesine izin vermesi ZORUNLUDUR.
Cihaz uygulamaları android.software.device_admin
raporunu veriyorsa:
[C-13-1]
android.app.action.ADD_DEVICE_ADMIN
, cihaz yöneticisini sisteme ekleyerek (veya reddetmesine izin vererek) kullanıcıyı getirecek bir kullanıcı arayüzünü çağırma amacına uyması ZORUNLUDUR.[C-13-2] android.app.action.PROVISION_MANAGED_PROFILE , android.app.action.SET_NEW_PARENT_PROFILE_PASSWORD , android.app.action.SET_NEW_PASSWORD ve android.app.action.START_ENCRYPTION niyetlerine uymalı ve bunların yerine getirilmesini sağlayacak bir etkinliğe sahip olmalı ZORUNLU bu amaçlar burada SDK'da açıklandığı gibidir.
Cihaz uygulamaları android.software.autofill
özellik işaretini bildirirse:
- [C-14-1]
AutofillService
veAutofillManager
API'lerini tam olarak uygulamalı ve otomatik doldurmayı etkinleştirmek ve devre dışı bırakmak ve kullanıcı için varsayılan otomatik doldurma hizmetini değiştirmek için varsayılan uygulama ayarları menüsünü gösterme android.settings.REQUEST_SET_AUTOFILL_SERVICE amacını dikkate almalıdır.
Cihaz uygulamaları önceden yüklenmiş bir uygulama içeriyorsa veya üçüncü taraf uygulamaların kullanım istatistiklerine erişmesine izin vermek istiyorsa:
- [C-SR-2], android.permission.PACKAGE_USAGE_STATS iznini bildiren uygulamalar için
android.permission.PACKAGE_USAGE_STATS
amacına yanıt olarak kullanım istatistiklerine erişim vermek veya erişimi iptal etmek için kullanıcı tarafından erişilebilen bir mekanizma sağlaması KESİNLİKLE ÖNERİR.
Cihaz uygulamaları, önceden yüklenmiş uygulamalar da dahil olmak üzere herhangi bir uygulamanın kullanım istatistiklerine erişmesine izin vermemeyi planlıyorsa:
- [C-15-1] Hâlâ android.settings.ACTION_USAGE_ACCESS_SETTINGS niyet modelini işleyen bir etkinliğe sahip olması GEREKİR, ancak bunu işlem yapılmayan bir şekilde uygulamalıdır, yani kullanıcının erişim için reddedildiği zamankiyle eşdeğer bir davranışa sahip olması ZORUNLUDUR.
Cihaz uygulamaları, Ayarlar'da AutofillService_passwordsActivity tarafından belirtilen etkinliklere olan bağlantıları veya benzer bir mekanizma aracılığıyla kullanıcı şifrelerine olan bağlantıları ortaya çıkarırsa:
- [C-16-1] Kurulu tüm otomatik doldurma hizmetleri için bu tür bağlantılar gösterilmelidir ZORUNLU.
Cihaz uygulamaları VoiceInteractionService
destekliyorsa ve bu API'yi kullanan birden fazla uygulamanın aynı anda yüklü olması durumunda:
- [C-18-1]
android.settings.ACTION_VOICE_INPUT_SETTINGS
ses girişi ve yardım için varsayılan uygulama ayarları menüsünü gösterme amacına uyması ZORUNLUDUR.
Cihaz uygulamaları android.hardware.audio.output
özelliğini rapor ediyorsa:
- [C-SR-3] Android.intent.action.TTS_SERVICE, android.speech.tts.engine.INSTALL_TTS_DATA ve android.speech.tts.engine.GET_SAMPLE_TEXT amaçlarının dikkate alınması, bu amaçların yerine getirilmesini sağlayacak bir etkinliğe sahip olması KESİNLİKLE ÖNERİLMEKTEDİR: Burada SDK'da açıklanmıştır.
Android, daha önce Dreams olarak adlandırılan etkileşimli ekran koruyucular için destek içerir. Ekran Koruyucular, bir güç kaynağına bağlı bir cihaz boştayken veya masaüstü dock'a yerleştirilmişken kullanıcıların uygulamalarla etkileşimde bulunmasına olanak tanır. Cihaz Uygulamaları:
- Ekran koruyucular için destek içermeli ve kullanıcıların
android.settings.DREAM_SETTINGS
amacına yanıt olarak ekran koruyucuları yapılandırmaları için bir ayar seçeneği sunmalıdır GEREKLİ.
3.2.4. İkincil/çoklu ekranlardaki etkinlikler
Cihaz uygulamaları normal Android Etkinliklerinin birden fazla ekranda başlatılmasına izin veriyorsa:
- [C-1-1]
android.software.activities_on_secondary_displays
özellik işaretini ayarlaması ZORUNLUDUR. - [C-1-2] Birincil ekranda çalışan bir etkinliğe benzer şekilde API uyumluluğunu garanti etmesi ZORUNLUDUR.
- [C-1-3] Yeni aktivite
ActivityOptions.setLaunchDisplayId()
API aracılığıyla bir hedef ekran belirtilmeden başlatıldığında, yeni aktiviteyi onu başlatan aktiviteyle aynı ekrana yerleştirmesi ZORUNLUDUR. - [C-1-4]
Display.FLAG_PRIVATE
bayrağını taşıyan bir ekran kaldırıldığında tüm etkinliklerin yok edilmesi ZORUNLUDUR. - [C-1-5] Uygulama
Activity#setShowWhenLocked()
API'sini kullanarak kilit ekranının üstünde gösterilmeyi seçmediği sürece, cihaz güvenli bir kilit ekranıyla kilitlendiğinde tüm ekranlardaki içeriği güvenli bir şekilde GİZLEMELİDİR. - İkincil ekranda bir etkinlik başlatıldığında görüntülenmesi, doğru çalışması ve uyumluluğun sürdürülmesi için bu ekrana karşılık gelen
android.content.res.Configuration
sahip olması GEREKİR.
Cihaz uygulamaları ikincil ekranlarda normal Android Faaliyetlerinin başlatılmasına izin veriyorsa ve ikincil ekranda android.view.Display.FLAG_PRIVATE bayrağı varsa:
- [C-3-1] Yalnızca bu ekranın, sistemin sahibi ve halihazırda o ekranda bulunan etkinlikler, onu başlatabilmelidir ZORUNLU. Herkes android.view.Display.FLAG_PUBLIC bayrağına sahip bir ekranı başlatabilir.
3.3. Yerel API Uyumluluğu
Yerel kod uyumluluğu zordur. Bu nedenle cihaz uygulayıcıları:
- [C-SR-1] Aşağıda listelenen kitaplıkların uygulamalarının yukarı akışlı Android Açık Kaynak Projesi'nden kullanılması ŞİDDETLE TAVSİYE EDİLİR.
3.3.1. Uygulama İkili Arayüzleri
Yönetilen Dalvik bayt kodu, uygulama .apk
dosyasında sağlanan yerel kodu, uygun cihaz donanım mimarisi için derlenmiş bir ELF .so
dosyası olarak çağırabilir. Yerel kod büyük ölçüde temel işlemci teknolojisine bağlı olduğundan Android, Android NDK'da bir dizi Uygulama İkili Arayüzü (ABI) tanımlar.
Cihaz uygulamaları:
- [C-0-1] Bir veya daha fazla tanımlanmış Android NDK ABI ile uyumlu OLMALIDIR.
- [C-0-2] Standart Java Yerel Arayüzü (JNI) semantiğini kullanarak, yerel kodu çağırmak için yönetilen ortamda çalışan kod desteğini içermelidir ZORUNLU.
- [C-0-3] aşağıdaki listede yer alan her gerekli kitaplık ile kaynak uyumlu (yani başlık uyumlu) ve ikili uyumlu (ABI için) OLMALIDIR.
- [C-0-5]
android.os.Build.SUPPORTED_ABIS
,android.os.Build.SUPPORTED_32_BIT_ABIS
veandroid.os.Build.SUPPORTED_64_BIT_ABIS
parametreleri aracılığıyla cihazın desteklediği yerel Uygulama İkili Arayüzünü (ABI) doğru bir şekilde raporlaması GEREKİR , her biri en çok tercih edilenden en az tercih edilene doğru sıralanmış ABI'lerin virgülle ayrılmış listesidir. [C-0-6] Yukarıdaki parametreler aracılığıyla aşağıdaki ABI listesinin bir alt kümesini rapor etmesi ZORUNLU ve listede olmayan herhangi bir ABI'yi rapor ETMEMELİDİR.
-
armeabi
(artık NDK tarafından hedef olarak desteklenmiyor) -
armeabi-v7a
-
arm64-v8a
-
x86
-
x86-64
-
[C-0-7] Yerel API'ler sağlayan aşağıdaki kitaplıkların tümünü, yerel kod içeren uygulamalar için kullanılabilir hale getirmesi GEREKİR:
- libaaudio.so (AAudio yerel ses desteği)
- libamidi.so (bölüm 5.9'da açıklandığı gibi
android.software.midi
özelliği talep ediliyorsa yerel MIDI desteği) - libandroid.so (yerel Android etkinlik desteği)
- libc (C kütüphanesi)
- libcamera2ndk.so
- libdl (dinamik bağlayıcı)
- libEGL.so (yerel OpenGL yüzey yönetimi)
- libGLESv1_CM.so (OpenGL ES 1.x)
- libGLESv2.so (OpenGL ES 2.0)
- libGLESv3.so (OpenGL ES 3.x)
- libicui18n.so
- libicuuc.so
- libjnigraphics.so
- liblog (Android günlüğü)
- libmediandk.so (yerel medya API'leri desteği)
- libm (matematik kütüphanesi)
- libneuralnetworks.so (Sinir Ağları API'si)
- libOpenMAXAL.so (OpenMAX AL 1.0.1 desteği)
- libOpenSLES.so (OpenSL ES 1.0.1 ses desteği)
- libRS.so
- libstdc++ (C++ için minimum destek)
- libvulkan.so (Vulkan)
- libz (Zlib sıkıştırması)
- JNI arayüzü
[C-0-8] Yukarıda listelenen yerel kütüphaneler için ortak işlevleri eklememeli veya kaldırmamalıdır.
[C-0-9]
/vendor/etc/public.libraries.txt
dosyasında doğrudan üçüncü taraf uygulamalara sunulan AOSP olmayan ek kitaplıkların listelenmesi ZORUNLUDUR.[C-0-10] AOSP'de sistem kitaplıkları olarak uygulanan ve sağlanan diğer yerel kitaplıkları, ayrılmış oldukları için API düzeyi 24 veya daha üstünü hedefleyen üçüncü taraf uygulamalara maruz bırakmamalıdır *ZORUNLU*.
[C-0-11] NDK'da tanımlandığı şekilde tüm OpenGL ES 3.1 ve Android Extension Pack işlev sembollerinin
libGLESv3.so
kitaplığı aracılığıyla dışa aktarılması ZORUNLUDUR. Tüm sembollerin mevcut olması ZORUNLU olsa da, bölüm 7.1.4.1'de, karşılık gelen her fonksiyonun tam olarak uygulanmasının ne zaman bekleneceğine ilişkin gereklilikler daha ayrıntılı olarak açıklanmaktadır.[C-0-12] Temel Vulkan 1.0 işlev simgelerinin yanı sıra
VK_KHR_surface
,VK_KHR_android_surface
,VK_KHR_swapchain
,VK_KHR_maintenance1
veVK_KHR_get_physical_device_properties2
uzantılarına ilişkin işlev simgelerininlibvulkan.so
kitaplığı aracılığıyla dışa aktarılması GEREKİR. Tüm simgelerin mevcut olması ZORUNLU olsa da, bölüm 7.1.4.2'de, karşılık gelen her işlevin tam olarak uygulanmasının ne zaman bekleneceğine ilişkin gereksinimler daha ayrıntılı olarak açıklanmaktadır.Yukarı akışlı Android Açık Kaynak Projesinde bulunan kaynak kodu ve başlık dosyaları kullanılarak OLUŞTURULMALIDIR
Android'in gelecek sürümlerinin ek ABI'ler için destek sunabileceğini unutmayın.
3.3.2. 32-bit ARM Yerel Kod Uyumluluğu
Cihaz uygulamaları armeabi
ABI desteğini bildirirse:
- [C-3-1]
armeabi
yalnızca eski uygulamalarla geriye dönük uyumluluk için olduğundan,armeabi-v7a
da desteklemeli ve desteğini bildirmelidir.
Cihaz uygulamaları, bu ABI'yi kullanan uygulamalar için armeabi-v7a
ABI desteğini bildirirse:
[C-2-1]
/proc/cpuinfo
dosyasına aşağıdaki satırlar dahil edilmelidir ZORUNLU ve diğer ABI'ler tarafından okunsalar bile aynı cihazdaki değerleri DEĞİŞTİRMEMELİDİR.-
Features:
, ardından cihaz tarafından desteklenen isteğe bağlı ARMv7 CPU özelliklerinin bir listesi gelir. -
CPU architecture:
, ardından cihazın desteklenen en yüksek ARM mimarisini açıklayan bir tamsayı gelir (örneğin, ARMv8 cihazları için "8").
-
[C-2-2] ABI'nin bir ARMv8 mimarisinde uygulandığı durumda bile, yerel CPU desteği veya yazılım emülasyonu aracılığıyla aşağıdaki işlemleri her zaman kullanılabilir tutması ZORUNLU:
- SWP ve SWPB talimatları.
- CP15ISB, CP15DSB ve CP15DMB bariyer işlemleri.
[C-2-3] Gelişmiş SIMD (diğer adıyla NEON) uzantısını desteklemelidir ZORUNLU.
3.4. Web Uyumluluğu
3.4.1. Web Görünümü Uyumluluğu
Cihaz uygulamaları android.webkit.Webview
API'sinin eksiksiz bir uygulamasını sağlıyorsa:
- [C-1-1]
android.software.webview
bildirmeniz ZORUNLUDUR. - [C-1-2]
android.webkit.WebView
API'sinin uygulanması için Android 12 dalındaki yukarı akışlı Android Açık Kaynak Projesinden Chromium Projesi derlemesini KULLANMALIDIR. [C-1-3] Web Görünümü tarafından bildirilen kullanıcı aracısı dizesi şu formatta OLMALIDIR:
Mozilla/5.0 (Linux; Android $(VERSION); [$(MODEL)] [Build/$(BUILD)]; wv) AppleWebKit/537.36 (KHTML, like Gecko) Sürüm/4.0 $(CHROMIUM_VER) Mobile Safari/537.36
- $(VERSION) dizesinin değeri, android.os.Build.VERSION.RELEASE değeriyle aynı OLMALIDIR.
- $(MODEL) dizesi boş OLABİLİR, ancak boş değilse android.os.Build.MODEL ile aynı değere sahip olması ZORUNLUDUR.
- "Build/$(BUILD)" atlanabilir OLABİLİR, ancak mevcutsa $(BUILD) dizesinin android.os.Build.ID değeriyle aynı olması ZORUNLUDUR.
- $(CHROMIUM_VER) dizesinin değeri, yukarı akışlı Android Açık Kaynak Projesindeki Chromium sürümü OLMALIDIR.
- Cihaz uygulamaları, kullanıcı aracısı dizesinde Mobil'i ihmal edebilir.
WebView bileşeninin mümkün olduğu kadar çok sayıda HTML5 özelliğini desteklemesi GEREKLİdir ve özelliği destekliyorsa HTML5 spesifikasyonuna uyması GEREKLİdir.
[C-1-4] Sağlanan içeriğin veya uzak URL içeriğinin, Web Görünümünü başlatan uygulamadan farklı bir süreçte İŞLENMESİ ZORUNLUDUR. Özellikle, ayrı oluşturucu işleminin daha düşük ayrıcalıklara sahip olması, ayrı bir kullanıcı kimliği olarak çalıştırılması, uygulamanın veri dizinine erişimi olmaması, doğrudan ağ erişiminin olmaması ve Binder üzerinden yalnızca gerekli minimum sistem hizmetlerine erişimi olması ZORUNLUDUR. WebView'ın AOSP uygulaması bu gereksinimi karşılar.
Cihaz uygulamaları 32 bit ise veya android.hardware.ram.low
özellik işaretini bildiriyorsa, bunların C-1-3'ten muaf olduğunu unutmayın.
3.4.2. Tarayıcı Uyumluluğu
Cihaz uygulamaları genel web taraması için bağımsız bir Tarayıcı uygulaması içeriyorsa:
- [C-1-1] HTML5 ile ilişkili şu API'lerin her birini DESTEKLEMELİ ZORUNLU:
- [C-1-2] HTML5/W3C web depolama API'sini desteklemesi ZORUNLU ve HTML5/W3C IndexedDB API'sini desteklemesi GEREKİR. Web geliştirme standartları kuruluşları web depolama yerine IndexedDB'yi tercih etmeye başladıkça, IndexedDB'nin Android'in gelecekteki bir sürümünde gerekli bir bileşen haline gelmesinin beklendiğini unutmayın.
- Bağımsız Tarayıcı uygulamasında özel bir kullanıcı aracısı dizesi GÖNDEREBİLİR.
- Bağımsız Tarayıcı uygulamasında (ister yukarı akışlı WebKit Tarayıcı uygulamasına ister üçüncü taraf bir değiştirmeye dayalı olsun) mümkün olduğunca fazla HTML5 desteği GERÇEKLEŞTİRİLMELİDİR.
Ancak cihaz uygulamaları bağımsız bir Tarayıcı uygulaması içermiyorsa:
- [C-2-1] Bölüm 3.2.3.1'de açıklanan genel niyet modellerini hala DESTEKLEMELİ ZORUNLU.
3.5. API Davranış Uyumluluğu
Cihaz uygulamaları:
- [C-0-9] Bölüm 3.5.1'de açıklandığı gibi kısıtlanmadıkça, yüklü tüm uygulamalar için API davranış uyumluluğunun uygulandığından GÜVENLİDİR.
- [C-0-10] Yalnızca cihaz uygulayıcıları tarafından seçilen uygulamalar için API davranışsal uyumluluğunu sağlayan izin verilenler listesine ekleme yaklaşımını UYGULAMAMALIDIR.
API türlerinin her birinin (yönetilen, yazılım, yerel ve web) davranışları, yukarı akışlı Android Açık Kaynak Projesinin tercih edilen uygulamasıyla tutarlı olmalıdır. Bazı spesifik uyumluluk alanları şunlardır:
- [C-0-1] Cihazlar standart bir amacın davranışını veya anlamını DEĞİŞTİRMEMELİDİR.
- [C-0-2] Cihazlar, belirli bir sistem bileşeni türünün (Servis, Etkinlik, ContentProvider vb.) yaşam döngüsünü veya yaşam döngüsü semantiğini DEĞİŞTİRMEMELİDİR.
- [C-0-3] Cihazlar standart bir iznin anlamını DEĞİŞTİRMEMELİDİR.
- Cihazlar, arka plan uygulamalarında uygulanan sınırlamaları DEĞİŞTİRMEMELİDİR. Daha spesifik olarak arka plan uygulamaları için:
- [C-0-4]
GnssMeasurement
veGnssNavigationMessage
çıktı almak için uygulama tarafından kaydedilen geri aramaları yürütmeyi durdurmaları GEREKİR. - [C-0-5]
LocationManager
API sınıfı veyaWifiManager.startScan()
yöntemi aracılığıyla uygulamaya sağlanan güncellemelerin sıklığını sınırlamaları GEREKİR. - [C-0-6] eğer uygulama API seviyesi 25 veya daha üstünü hedefliyorsa, yayın amacı bir
"signature"
veya"signatureOrSystem"
gerektirmediği sürece, uygulamanın bildiriminde standart Android amaçlarının örtülü yayınları için yayın alıcılarının kaydedilmesine izin VERMEMELİDİR""signatureOrSystem"
protectionLevel
izni veya muafiyet listesinde yer alıyor. - [C-0-7] Uygulama, API düzeyi 25 veya daha üstünü hedefliyorsa, uygulama geçici bir izin verilenler listesine yerleştirilmediği sürece, sanki uygulama hizmetlerin
stopSelf()
yöntemini çağırmış gibi, uygulamanın arka plan hizmetlerini DURDURMALIDIRLAR Kullanıcının görebileceği bir görevi gerçekleştirmek için. - [C-0-8] Uygulama, API düzeyi 25 veya daha üstünü hedefliyorsa, uygulamanın tuttuğu uyanık kalma kilitlerini serbest bırakmaları GEREKİR.
- [C-0-4]
- [C-0-11] Cihazların, aşağıdaki güvenlik sağlayıcılarını
Security.getProviders()
yönteminden ilk yedi dizi değeri olarak, verilen sırayla ve verilen adlarla (Provider.getName()
tarafından döndürüldüğü gibi) ve sınıflarla döndürmesi ZORUNLUDUR. , uygulama listeyiinsertProviderAt()
veyaremoveProvider()
yoluyla değiştirmediği sürece. Cihazlar, aşağıda belirtilen sağlayıcı listesinden sonra ek sağlayıcılar döndürebilir.- AndroidNSSP -
android.security.net.config.NetworkSecurityConfigProvider
- AndroidOpenSSL -
com.android.org.conscrypt.OpenSSLProvider
- CertPathProvider -
sun.security.provider.CertPathProvider
- AndroidKeyStoreBCWorkaround -
android.security.keystore.AndroidKeyStoreBCWorkaroundProvider
- BC -
com.android.org.bouncycastle.jce.provider.BouncyCastleProvider
- HarmonyJSSE -
com.android.org.conscrypt.JSSEProvider
- AndroidKeyStore -
android.security.keystore.AndroidKeyStoreProvider
- AndroidNSSP -
Yukarıdaki liste kapsamlı değildir. Uyumluluk Testi Suite (CTS), davranışsal uyumluluk için platformun önemli kısımlarını test eder, ancak hepsi değil. Android Açık Kaynak Projesi ile davranışsal uyumluluğu sağlamak uygulayıcının sorumluluğundadır. Bu nedenle, cihaz uygulayıcıları, sistemin önemli bölümlerini yeniden uygulamak yerine, mümkün olduğunca Android açık kaynak projesi aracılığıyla kullanılabilir kaynak kodu kullanmalıdır.
3.5.1. Uygulama kısıtlaması
Cihaz uygulamaları uygulamaları kısıtlamak için tescilli bir mekanizma uyguluyorsa ve bu mekanizma kısıtlı uygulama bekleme kovasından daha kısıtlıysa, bunlar:
- [C-1], kullanıcının kısıtlı uygulamalar listesini görebileceği kullanıcı uygunluğu sağlamalıdır.
- [C-1-2], her uygulamadaki kısıtlamaları açmak / kapatmak için kullanıcının uygunluğu sağlamalıdır.
- [C-1-3], kötü sistem sağlığı davranışının kanıtı olmadan kısıtlamaları otomatik olarak uygulamamalıdır, ancak sıkışmış Wakelocks, uzun süren hizmetler ve diğer kriterler gibi kötü sistem sağlığı davranışlarının tespiti üzerine uygulamalardaki kısıtlamaları uygulayabilir. Kriterler cihaz uygulayıcıları tarafından belirlenebilir, ancak uygulamanın sistem sağlığı üzerindeki etkisi ile ilişkili olmalıdır. Uygulamanın piyasadaki popülerlik eksikliği gibi yalnızca sistem sağlığı ile ilgili olmayan diğer kriterler kriter olarak kullanılmamalıdır.
- [C-1-4], bir kullanıcı uygulama kısıtlamalarını manuel olarak kapattığında uygulamalar için uygulama kısıtlamalarını otomatik olarak uygulamamalıdır ve kullanıcının uygulama kısıtlamalarını uygulamasını önerebilir.
- [C-1-5], bir uygulamaya otomatik olarak uygulama kısıtlamaları uygulanırsa kullanıcıları bilgilendirmelidir. Bu tür bilgiler, kısıtlamaların uygulandığı zaman 24 saat içinde sağlanmalıdır.
- [C-1-6], kısıtlı uygulama bu API'yı çağırdığında
ActivityManager.isBackgroundRestricted()
içintrue
dönmelidir. - [C-1-7], kullanıcı tarafından açıkça kullanılan üst ön plan uygulamasını kısıtlamamalıdır.
- [C-1-8] Kullanıcı, kısıtlanmış olan uygulamayı açıkça kullanmaya başladığında, üst ön plan uygulaması haline gelen bir uygulamadaki kısıtlamaları askıya almalıdır.
- [C-1-9] tüm uygulama kısıtlama olaylarını
UsageStats
aracılığıyla bildirmelidir. - [C-1-10] bir uygulamanın bir kullanıcı tarafından en son kullanımdan itibaren 2 saat içinde kısıtlı kovaya otomatik olarak yerleştirilmesine izin vermemelidir.
Cihaz uygulamaları AOSP'de uygulanan uygulama kısıtlamalarını genişletirse, bunlar:
- [C-2-1] bu belgede açıklanan uygulamayı izlemelidir.
3.5.2. Uygulama kış uykusu
Cihaz uygulamaları, AOSP'ye dahil edilen veya AOSP'ye dahil olan özelliği genişleten uygulama kış uykusunu içeriyorsa,:
- [C-1], [C-1-6] ve [C-1-3] hariç Bölüm 3.5.1'deki tüm gereksinimleri karşılamalıdır.
- [C-1-2], kullanıcının uygulamayı bir süre kullanmadığına dair kanıt olduğunda yalnızca bir kullanıcı için uygulamaya kısıtlamayı uygulamalıdır. Bu sürenin bir ay veya daha uzun olması şiddetle tavsiye edilir. Kullanım, UsAgestats#getLastTimeVicle () API veya bir uygulamanın hizmet bağlamaları, içerik sağlayıcı bağları, açık yayınlar vb. yeni bir API USAGESTATS#getLastTimeanyComponentused ().
- [C-1-3], paketin herhangi bir kullanıcı tarafından bir süre kullanılmadığına dair kanıt olduğunda, tüm cihaz kullanıcılarını etkileyen kısıtlamalar uygulamalıdır. Bu sürenin bir ay veya daha uzun olması şiddetle tavsiye edilir.
- [C-1-4] uygulamayı etkinlik niyetlerine, hizmet bağlarına, içerik sağlayıcı isteklerine veya açık yayınlara yanıt verememelidir.
AOSP'de uygulama hazırda bekletme yukarıdaki gereksinimleri karşılamaktadır.
3.6. API ad alanları
Android, Java programlama dili tarafından tanımlanan paket ve sınıf ad alanı kurallarını takip eder. Üçüncü taraf uygulamalarla uyumluluğu sağlamak için, cihaz uygulayıcıları bu paket ad alanlarında yasaklanmış herhangi bir değişiklik yapmamalı (aşağıya bakınız):
-
java.*
-
javax.*
-
sun.*
-
android.*
-
androidx.*
-
com.android.*
Yani, onlar:
- [C-0-1], herhangi bir yöntem veya sınıf imzasını değiştirerek veya sınıfları veya sınıf alanlarını kaldırarak Android platformunda kamuya açık API'leri değiştirmemelidir.
- [C-0-2], yukarıdaki ad alanlarındaki API'lara kamuya açık bir öğe (sınıflar veya arayüzler veya mevcut sınıflara veya arayüzlere veya arayüzlere veya sistem API'larına veya test veya sistem API'larına eklememelidir. “Halka açık bir öğe”, yukarı akış Android kaynak kodunda kullanılan “@hide” işaretçisi ile dekore edilmeyen herhangi bir yapıdır.
Cihaz uygulayıcıları API'lerin altında yatan uygulamayı değiştirebilir, ancak bu tür değişiklikler:
- [C-0-3], kamuya açık herhangi bir API'lerin belirtilen davranışı ve Java dili imzasını etkilememelidir.
- [C-0-4] Reklamı verilmemeli veya geliştiricilere başka bir şekilde maruz bırakılmamalıdır.
Ancak, cihaz uygulayıcıları standart Android ad alanı dışında özel API'ler ekleyebilir, ancak özel API'lar:
- [C-0-5] başka bir kuruluşa ait veya başka bir kuruluşa ait bir ad alanında olmamalıdır. Örneğin, cihaz uygulayıcıları
com.google.*
Veya benzeri ad alanı: Yalnızca Google bunu yapabilir. Benzer şekilde, Google diğer şirketlerin ad alanlarına API eklememelidir. - [C-0-6], Android paylaşılan bir kitaplıkta paketlenmelidir, böylece bunları yalnızca bunları açıkça kullanan uygulamalar (<Usessitary> Mekanizma aracılığıyla) bu tür API'ların artan bellek kullanımından etkilenir.
Cihaz uygulayıcıları, NDK API'lerinin dışında ana dillerde özel API'ler ekleyebilir, ancak özel API'lar:
- [C-1], burada açıklandığı gibi başka bir kuruluşun NDK kütüphanesinde veya bir kütüphanede olmamalıdır.
Bir cihaz uygulayıcısı, yukarıdaki paket ad alanlarından birini geliştirmeyi öneriyorsa (mevcut bir API'ya yararlı yeni işlevler ekleyerek veya yeni bir API ekleyerek), uygulayıcı kaynakları ziyaret etmeli ve değişikliklere katkıda bulunma işlemine başlamalı ve işlemi başlatmalıdır ve Kod, o sitedeki bilgilere göre.
Yukarıdaki kısıtlamaların, Java programlama dilinde API'lerin adlandırılması için standart kurallara karşılık geldiğini unutmayın; Bu bölüm sadece bu sözleşmeleri güçlendirmeyi ve bu uyumluluk tanımına dahil edilerek onları bağlamayı amaçlamaktadır.
3.7. Çalışma zamanı uyumluluğu
Cihaz uygulamaları:
[C-0-1] tam Dalvik Yürütülebilir (DEX) formatını ve Dalvik Bytecode spesifikasyonu ve anlambilimini desteklemelidir.
[C-0-2], Dalvik Runtimes'i yukarı akış Android platformuna uygun olarak ve aşağıdaki tabloda belirtildiği şekilde bellek tahsis etmek için yapılandırmalıdır. (Ekran boyutu ve ekran yoğunluğu tanımları için Bölüm 7.1.1'e bakın.)
Android Çalışma Zamanı'nı (ART), Dalvik Yürütülebilir Formatının referans yukarı akış uygulamasını ve referans uygulamanın paket yönetim sistemini kullanmalıdır.
Çalışma zamanının istikrarını sağlamak için çeşitli yürütme modları ve hedef mimariler altında Fuzz testleri yapmalıdır. Android Açık Kaynak Proje web sitesinde JFuzz ve Dexfuzz'a bakın.
Aşağıda belirtilen bellek değerlerinin minimum değerler olarak kabul edildiğini ve cihaz uygulamalarının uygulama başına daha fazla bellek tahsis edebileceğini unutmayın.
Ekran düzeni | Ekran Yoğunluğu | Minimum uygulama belleği |
---|---|---|
Android Watch | 120 DPI (LDPI) | 32MB |
140 DPI (140dpi) | ||
160 DPI (MDPI) | ||
180 DPI (180dpi) | ||
200 dpi (200dpi) | ||
213 DPI (TVDPI) | ||
220 DPI (220dpi) | 36MB | |
240 DPI (HDPI) | ||
280 DPI (280dpi) | ||
320 DPI (XHDPI) | 48MB | |
360 DPI (360dpi) | ||
400 dpi (400dpi) | 56MB | |
420 DPI (420dpi) | 64MB | |
480 DPI (xxhdpi) | 88MB | |
560 DPI (560dpi) | 112MB | |
640 dpi (xxxhdpi) | 154MB | |
Küçük/Normal | 120 DPI (LDPI) | 32MB |
140 DPI (140dpi) | ||
160 DPI (MDPI) | ||
180 DPI (180dpi) | 48MB | |
200 dpi (200dpi) | ||
213 DPI (TVDPI) | ||
220 DPI (220dpi) | ||
240 DPI (HDPI) | ||
280 DPI (280dpi) | ||
320 DPI (XHDPI) | 80MB | |
360 DPI (360dpi) | ||
400 dpi (400dpi) | 96MB | |
420 DPI (420dpi) | 112MB | |
480 DPI (xxhdpi) | 128MB | |
560 DPI (560dpi) | 192MB | |
640 dpi (xxxhdpi) | 256MB | |
büyük | 120 DPI (LDPI) | 32MB |
140 DPI (140dpi) | 48MB | |
160 DPI (MDPI) | ||
180 DPI (180dpi) | 80MB | |
200 dpi (200dpi) | ||
213 DPI (TVDPI) | ||
220 DPI (220dpi) | ||
240 DPI (HDPI) | ||
280 DPI (280dpi) | 96MB | |
320 DPI (XHDPI) | 128MB | |
360 DPI (360dpi) | 160MB | |
400 dpi (400dpi) | 192MB | |
420 DPI (420dpi) | 228MB | |
480 DPI (xxhdpi) | 256MB | |
560 DPI (560dpi) | 384MB | |
640 dpi (xxxhdpi) | 512MB | |
xlarge | 120 DPI (LDPI) | 48MB |
140 DPI (140dpi) | 80MB | |
160 DPI (MDPI) | ||
180 DPI (180dpi) | 96MB | |
200 dpi (200dpi) | ||
213 DPI (TVDPI) | ||
220 DPI (220dpi) | ||
240 DPI (HDPI) | ||
280 DPI (280dpi) | 144MB | |
320 DPI (XHDPI) | 192MB | |
360 DPI (360dpi) | 240MB | |
400 dpi (400dpi) | 288MB | |
420 DPI (420dpi) | 336MB | |
480 DPI (xxhdpi) | 384MB | |
560 DPI (560dpi) | 576MB | |
640 dpi (xxxhdpi) | 768MB |
3.8. Kullanıcı arayüzü uyumluluğu
3.8.1. Launcher (Ana Ekran)
Android, bir başlatıcı uygulaması (ana ekran) ve aygıt başlatıcısının (ana ekran) değiştirilmesi için üçüncü taraf uygulamalar için destek içerir.
Cihaz uygulamaları, üçüncü taraf uygulamaların cihaz ana ekranını değiştirmesine izin veriyorsa, bunlar:
- [C-1]
android.software.home_screen
platform özelliğini bildirmelidir. - [C-1-2], simgelerini sağlamak için üçüncü taraf uygulaması
<adaptive-icon>
etiketini kullandığında ve simgeleri almak içinPackageManager
yöntemleri çağrıldığındaAdaptiveIconDrawable
nesnesini döndürmelidir.
Cihaz uygulamaları, kısayolların uygulama içi sabitlemesini destekleyen varsayılan bir başlatıcı içeriyorsa, bunlar:
- [C-2-1] true
ShortcutManager.isRequestPinShortcutSupported()
içintrue
bildirmelidir. - [C-2-2]
ShortcutManager.requestPinShortcut()
API yöntemi aracılığıyla uygulamalar tarafından istenen bir kısayol eklemeden önce kullanıcıya soran kullanıcı uygunluğuna sahip olmalıdır. - [C-2-3] Uygulama Kısayolları sayfasında belgelendiği gibi sabitlenmiş kısayolları ve dinamik ve statik kısayolları desteklemelidir.
Tersine, cihaz uygulamaları kısayolların uygulama içi sabitlemesini desteklemiyorsa, bunlar:
- [C-3-1]
false
içinShortcutManager.isRequestPinShortcutSupported()
.
Cihaz uygulamaları, KısaTutManager API'sı aracılığıyla üçüncü taraf uygulamalar tarafından sağlanan ek kısayollara hızlı erişim sağlayan varsayılan bir başlatıcı uyguluyorsa, bunlar:
- [C-4-1] belgelenmiş tüm kısayol özelliklerini (örneğin statik ve dinamik kısayollar, sabitleme kısayolları) desteklemeli ve
ShortcutManager
API sınıfının API'lerini tam olarak uygulamalıdır.
Cihaz uygulamaları, uygulama simgeleri için rozetler gösteren varsayılan bir başlatıcı uygulaması içeriyorsa, bunlar:
- [C-5-1]
NotificationChannel.setShowBadge()
API yöntemine saygı duymalıdır. Başka bir deyişle, değertrue
olarak ayarlanmışsa, uygulama simgesiyle ilişkili görsel bir karşılama gösterin ve uygulamanın tüm bildirim kanalları değerifalse
olarak ayarladığında herhangi bir uygulama simgesi rozet şeması göstermeyin. - Üçüncü taraf uygulamalar tescilli rozet şemasının tescilli API'lerin kullanımı yoluyla özel rozet şemasının desteğini gösterdiğinde, uygulama simgesi rozetlerini tescilli rozet şeması ile geçersiz kılabilir, ancak SDK'da açıklanan bildirim rozetleri API'leri aracılığıyla sağlanan kaynakları ve değerleri kullanmalıdır, örneğin
Notification.Builder.setNumber()
veNotification.Builder.setBadgeIconType()
API.
3.8.2. Widget'lar
Android, bir bileşen türü ve uygulamaların son kullanıcıya bir “AppWidget” ortaya çıkarmasına izin veren karşılık gelen API ve yaşam döngüsü tanımlayarak üçüncü taraf uygulama widget'larını destekler.
Cihaz uygulamaları üçüncü taraf uygulama widget'larını destekliyorsa, bunlar:
- [C-1]
android.software.app_widgets
platform özelliği için destek beyan etmelidir. - [C-1-2], AppWidgets için yerleşik destek içermeli ve AppWidgets'i doğrudan başlatıcı içine eklemek, yapılandırmak, görüntülemek ve kaldırmak için kullanıcı arayüzü uygunluklarını ortaya çıkarmalıdır.
- [C-1-3], standart ızgara boyutunda 4 x 4 olan widget'ları oluşturabilmelidir. Ayrıntılar için Android SDK belgelerindeki App Widget DesignGuidelines'e bakın.
- Kilit ekranında uygulama widget'larını destekleyebilir.
Cihaz uygulamaları üçüncü taraf uygulama widget'larını ve kısayolların uygulama içi sabitlemesini destekliyorsa, bunlar:
- [C-2-1]
AppWidgetManager.html.isRequestPinAppWidgetSupported()
içintrue
rapor etmelidir. - [C-2-2]
AppWidgetManager.requestPinAppWidget()
API yöntemi aracılığıyla uygulamalar tarafından istenen bir kısayol eklemeden önce kullanıcıya soran kullanıcı uygunluğu olmalıdır.
3.8.3. Bildirimler
Android, üçüncü taraf uygulama geliştiricilerinin kullanıcıları dikkate değer etkinlikleri (örn. Ses, titreşim ve ışık) ve cihazın yazılım özelliklerini (örn. Bildirim gölgesi, sistem çubuğu) kullanarak kullanıcılara dikkat çekmesine ve kullanıcıların dikkatini çekmelerine izin veren Notification
ve NotificationManager
API'leri içerir. .
3.8.3.1. Bildirimlerin sunumu
Cihaz uygulamaları üçüncü taraf uygulamalarının kullanıcıları önemli etkinlikler hakkında bilgilendirmesine izin veriyorsa, bunlar:
- [C-1], SDK belgelerinde açıklandığı gibi ve cihaz uygulama donanımında mümkün olduğu ölçüde donanım özelliklerini kullanan bildirimleri desteklemelidir. Örneğin, bir cihaz uygulaması bir vibratör içeriyorsa, titreşim API'lerini doğru bir şekilde uygulamalıdır. Bir cihaz uygulaması donanım yoksa, ilgili API'ler op olarak uygulanmalıdır. Bu davranış bölüm 7'de daha ayrıntılı olarak açıklanmıştır.
- [C-1-2] API'larda veya durum/Sistem Çubuğu Simge Stili Kılavuzu'nda belirtilen tüm kaynakları (simgeler, animasyon dosyaları vb.) Doğru bir şekilde oluşturmalıdır, ancak bildirimler için bundan alternatif bir kullanıcı deneyimi sağlayabilirler. Referans Android Açık Kaynak Uygulaması tarafından sağlanır.
- [C-1-3] API'lerin bildirimleri güncellemesi, kaldırması ve gruplandırması için açıklanan davranışları onurlandırmalı ve uygulamalıdır.
- [C-1-4], SDK'da belgelenen NotificationChannel API'sının tam davranışını sağlamalıdır.
- [C-1-5], her kanal ve uygulama paketi seviyesi başına belirli bir üçüncü taraf uygulamasının bildirimini engellemek ve değiştirmek için bir kullanıcının uygunluğu sağlamalıdır.
- [C-1-6] ayrıca silinen bildirim kanallarını görüntülemek için bir kullanıcının uygunluğu sağlamalıdır.
- [C-1-7] Ek kullanıcı etkileşimi olmadan bildirim metninin yanında Notification.MessagingStyle aracılığıyla sağlanan tüm kaynakları (görüntüler, çıkartmalar, simgeler vb.) Doğru bir şekilde oluşturmalıdır. Örneğin, setGroupConversation aracılığıyla belirlenen bir grup konuşmasında Android.App.Person aracılığıyla sağlanan simgeler de dahil olmak üzere tüm kaynakları göstermelidir.
- [C-SR-1], kullanıcı bu bildirimi birden çok kez reddettikten sonra, her kanal ve uygulama paketi seviyesi başına belirli bir üçüncü taraf uygulamanın bildirimini engellemek için bir kullanıcının karşılaşmasını otomatik olarak ortaya çıkarması şiddetle tavsiye edilir.
- [C-SR-2], kullanıcının bildirim dinleyici izni verilen uygulamalara maruz kalan bildirimleri kontrol etmeleri için bir uygunluk sağlaması şiddetle tavsiye edilir. Tanrısallık, kullanıcının bu tür bir bildirim dinleyicisi için bu dinleyiciye hangi bildirim türlerinin köprülendiğini kontrol edebileceği şekilde olmalıdır. Türler "konuşmalar", "uyarma", "sessiz" ve "önemli devam eden" bildirimleri içermelidir.
- [C-SR-3], kullanıcıların herhangi bir belirli bildirim dinleyicisini bildirmekten hariç tutmaları için uygulamaları belirtmeleri için bir uygunluk sağlaması şiddetle tavsiye edilir.
- Zengin bildirimleri desteklemelidir.
- Heads-Up bildirimleri olarak bazı daha yüksek öncelik bildirimleri sunmalıdır.
- Bildirimleri ertelemek için bir kullanıcının uygunluğu olmalıdır.
- Yalnızca üçüncü taraf uygulamaların ne zaman kullanıcıları sürücü dikkat dağınıklığı gibi güvenlik sorunlarını azaltmak için kullanıcıları önemli olayları bildirebileceği görünürlüğünü ve zamanlamasını yönetebilir.
Android 11, mesajlaşma style kullanan ve yayınlanmış kişiler kısayol kimliği sağlayan bildirimler olan konuşma bildirimleri için destek sunar.
Cihaz uygulamaları:
- [C-SR-4], devam eden ön plan hizmet bildirimleri ve önemi hariç, konuşma olmayan bildirimler öncesinde
conversation notifications
gruplandırmanız ve görüntülemesi önerilirimportance:high
bildirimler.
Cihaz uygulamaları conversation notifications
destekliyor ve uygulama bubbles
için gerekli verileri sağlıyorsa, bunlar:
- [C-SR-5] bu konuşmayı bir balon olarak görüntülemeniz şiddetle tavsiye edilir. AOSP uygulaması, bu gereksinimleri varsayılan sistem kullanıcı arayüzü, ayarlar ve başlatıcı ile karşılar.
Cihaz uygulamaları zengin bildirimleri destekliyorsa, bunlar:
- [C-2-1], sunulan kaynak öğeleri için
Notification.Style
. -
Notification.Style
API sınıfında ve alt sınıflarında tanımlanan her kaynak öğesini (örneğin simge, başlık ve özet metin) sunmalıdır.
Cihaz uygulamaları Heads-Up Bildirimlerini Destekliyorsa: Onlar:
- [C-3-1] Heads-Up Bildirim görünümünü ve kaynaklarını
Notification.Builder
açıklandığı gibi kullanmalıdır. - [C-3-2], SDK'da açıklandığı gibi ek kullanıcı etkileşimi olmadan
Notification.Builder.addAction()
ile birlikte bildirim içeriği ile birlikte gösterilmelidir.
3.8.3.2. Bildirim Dinleyici Hizmeti
Android, uygulamaların (kullanıcı tarafından açıkça etkinleştirildikten sonra) tüm bildirimlerin bir kopyasını yayınlandıkları veya güncellendikçe almasına izin veren NotificationListenerService
API'lerini içerir.
Cihaz uygulamaları:
- [C-0-1], bildirim nesnesine bağlı tüm meta veriler dahil tüm bu tür yüklü ve kullanıcı özellikli dinleyici hizmetlerine bildirimleri doğru ve derhal güncellemelidir.
- [C-0-2]
snoozeNotification()
API çağrısına saygı duymalı ve bildirimi reddetmeli ve API çağrısında belirlenen erteleme süresinden sonra geri arama yapmalıdır.
Cihaz uygulamalarının bildirimleri ertelemek için bir kullanıcı uygunluğu varsa, bunlar:
- [C-1]
NotificationListenerService.getSnoozedNotifications()
gibi standart API'ler aracılığıyla ertelenmiş bildirim durumunu düzgün bir şekilde yansıtmalıdır. - [C-1-2], kalıcı/ön plan hizmetlerinden olmadıkça, yüklü her üçüncü taraf uygulamalarından gelen bildirimler için bu kullanıcının uygunluğunu kullanılabilir hale getirmelidir.
3.8.3.3. DND (rahatsız etmeyin)
Cihaz uygulamaları DND özelliğini destekliyorsa, bunlar:
- [C-1], cihaz uygulaması, kullanıcının DND ilke yapılandırmasına erişmek için üçüncü taraf uygulamaları vermesi veya reddetmesi için bir araç sağladığında, kullanıcı tarafından oluşturulan ve önceden uygulamalar tarafından oluşturulan otomatik DND kurallarını görüntüleyin. -tanımlanmış kurallar.
- [C-1-3]
NotificationManager.Policy
boyunca geçirilensuppressedVisualEffects
değerlerini onurlandırmalı ve bir uygulama baskıladığı_effect_screen_off veya baskılanmış_effect_screen_on bayraklarından herhangi birini ayarladıysa, kullanıcıya görsel efektlerin DND ayarları menüsünde bastırıldığını göstermelidir.
3.8.4. API'lara Yardım Edin
Android, uygulamaların mevcut bağlam hakkında ne kadar bilginin cihazdaki asistanla paylaşıldığını seçmesine izin vermek için API'leri içerir.
Cihaz uygulamaları yardım eylemini destekliyorsa, bunlar:
- [C-2-1], bağlam paylaşıldığında son kullanıcıya açıkça belirtmelidir:
- Assist uygulaması, ekranın kenarları etrafında Android Açık Kaynak Proje uygulamasının süresini ve parlaklığını karşılayan veya aşan beyaz bir ışık görüntüleyerek her bir içeriğe eriştiğinde.
- Önceden yüklenmiş Assist uygulaması için, kullanıcının varsayılan ses girişi ve yardımcı uygulama ayarları menüsünden ikiden daha az gezinme sağlayan ve yalnızca yardım uygulaması kullanıcı tarafından bir hotword veya yardımcı gezinme anahtarı girişinden açıkça çağrıldığında bağlamı paylaşmak.
- [C-2-2] Bölüm 7.2.3'te açıklandığı gibi ASIST uygulamasını başlatmak için belirlenen etkileşim, kullanıcı tarafından seçilen yardımcı uygulamayı başlatmalıdır, başka bir deyişle
VoiceInteractionService
veyaACTION_ASSIST
niyetini işleyen bir etkinlik.
3.8.5. Uyarılar ve tostlar
Uygulamalar, kısa bir süre sonra kaybolan son kullanıcıya kısa modal olmayan kısa dizeler görüntülemek için Toast
API'sını kullanabilir ve diğer uygulamalar üzerinde bir yerleşim olarak uyarı pencerelerini görüntülemek için TYPE_APPLICATION_OVERLAY
pencere türü API'sını kullanabilir.
Cihaz uygulamaları bir ekran veya video çıktısı içeriyorsa, bunlar:
[C-1], bir uygulamanın
TYPE_APPLICATION_OVERLAY
kullanan uyarı pencerelerini görüntülemesini engellemek için bir kullanıcının uygunluğu sağlamalıdır. AOSP uygulaması, bildirim gölgesinde kontroller yaparak bu gereksinimi karşılamaktadır.[C-1-2] tost API'sını onurlandırmalı ve son kullanıcılara uygulamalardan son derece görünür bir şekilde tostları göstermelidir.
3.8.6. Temalar
Android, uygulamaların bir etkinlik veya uygulamaya stil uygulaması için bir mekanizma olarak “temalar” sağlar.
Android, Android SDK tarafından tanımlandığı gibi Holo tema görünümünü ve hislerini eşleştirmek istiyorlarsa, uygulama geliştiricilerinin kullanmaları için bir dizi tanımlanmış stil olarak bir “holo” ve "malzeme" tema ailesini içerir.
Cihaz uygulamaları bir ekran veya video çıktısı içeriyorsa, bunlar:
- [C-1], uygulamalara maruz kalan holo tema niteliklerinden hiçbirini değiştirmemelidir.
- [C-1-2] “malzeme” tema ailesini desteklemeli ve maddi tema niteliklerini veya uygulamalara maruz kalan varlıklarını değiştirmemelidir.
- [C-1-3] Roboto'nun desteklediği diller için "sans-serif" yazı tipi ailesini Roboto sürüm 2.x olarak ayarlamalı veya "sans-serif" font ailesi için kullanılan yazı tipini değiştirmek için bir kullanıcı uygunluğu sağlamalı Roboto'nun desteklediği diller için Roboto sürüm 2.x.
Android ayrıca, cihaz uygulayıcısı tarafından tanımlanan cihaz temasının görünümünü ve hissini eşleştirmek istiyorlarsa, uygulama geliştiricilerinin kullanmaları için bir dizi tanımlanmış stil olarak bir “cihaz varsayılan” tema ailesi içerir.
- Cihaz uygulamaları, uygulamalara maruz kalan aygıt varsayılan tema özniteliklerini değiştirebilir.
Android, uygulama geliştiricilerinin durum ve navigasyon çubuğunun arkasındaki alanı uygulama içeriğiyle doldurmalarını sağlayan yarı saydam sistem çubuklarına sahip bir varyant temasını destekler. Bu yapılandırmada tutarlı bir geliştirici deneyimini sağlamak için, durum çubuğu simge stilinin farklı cihaz uygulamalarında korunması önemlidir.
Cihaz uygulamaları bir sistem durum çubuğu içeriyorsa, bunlar:
- [C-2-1], simge sorunlu bir durumu göstermedikçe veya bir uygulama WindowSetsController# kullanılarak bir ışık durumu çubuğu talep etmedikçe, sistem durum simgeleri (sinyal gücü ve pil seviyesi gibi) ve sistem tarafından verilen bildirimleri kullanmalıdır. Görünüm_light_status_bar bayrağı.
- [C-2-2] Android Cihaz Uygulamaları, bir uygulama bir ışık durumu çubuğu talep ettiğinde sistem durumu simgelerinin rengini siyah olarak değiştirmelidir (ayrıntılar için R.Style'a bakın).
3.8.7. Canlı Duvarkağıtları
Android, uygulamaların bir veya daha fazla “canlı duvar kağıtları” nı son kullanıcıya maruz bırakmasına izin veren bir bileşen türü ve karşılık gelen API ve yaşam döngüsü tanımlar. Canlı duvar kağıtları, diğer uygulamaların arkasında duvar kağıdı olarak görüntülenen sınırlı giriş özelliklerine sahip animasyonlar, desenler veya benzer görüntülerdir.
Donanım, tüm canlı duvar kağıtlarını çalıştırabiliyorsa, işlevsellik konusunda herhangi bir sınırlama olmadan, diğer uygulamalar üzerinde olumsuz bir etkisi olmayan makul bir kare hızında güvenilir bir şekilde canlı duvar kağıtları çalıştırabilir. Donanımdaki sınırlamalar duvar kağıtlarına ve/veya uygulamaların çökmesine, arızalanmasına, aşırı CPU veya pil gücü tüketmesine veya kabul edilemeyecek kadar düşük kare hızlarında çalışmasına neden olursa, donanımın canlı duvar kağıdı çalıştıramayacağını kabul eder. Örnek olarak, bazı canlı duvar kağıtları içeriğini oluşturmak için bir OpenGL 2.0 veya 3.x bağlam kullanabilir. Canlı duvar kağıdı, birden fazla OpenGL bağlamını desteklemeyen donanımda güvenilir bir şekilde çalışmaz, çünkü bir OpenGL bağlamının canlı duvar kağıdı kullanımı, OpenGL bağlamını da kullanan diğer uygulamalarla çelişebilir.
- Yukarıda açıklandığı gibi canlı duvar kağıtlarını güvenilir bir şekilde çalıştırabilen cihaz uygulamaları canlı duvar kağıtları uygulamalıdır.
Cihaz uygulamaları canlı duvar kağıtları uygularsa, bunlar:
- [C-1] android.software.live_wallpaper platform özelliğini bildirmelidir.
3.8.8. Etkinlik Değiştirme
Yukarı Akım Android kaynak kodu, görev değiştirme ve yakın zamanda erişilen etkinlikleri ve görevleri görüntüleyen sistem düzeyinde bir kullanıcı arayüzü olan Genel Bakış ekranını içerir.
Bölüm 7.2.3'te ayrıntılı olarak açıklandığı gibi Recents Fonksiyon Navigasyon Anahtarı dahil cihaz uygulamaları arayüzü değiştirebilir.
Bölüm 7.2.3'te ayrıntılı olarak açıklandığı gibi son kullanılanlar işlevi gezinme tuşunu içeren cihaz uygulamaları arayüzü değiştirirse:
- [C-1] en az 7'ye kadar gösterilen etkinliği desteklemelidir.
- En azından bir seferde 4 etkinlik başlığını göstermelidir.
- [C-1-2] ekran sabitleme davranışını uygulamalı ve kullanıcıya özelliği değiştirecek bir ayar menüsü sağlamalıdır.
- Recents olarak renk, simge, ekran başlığı göstermelidir.
- Bir kapanış uygunluğu ("x") göstermeli, ancak kullanıcı ekranlarla etkileşime girene kadar bunu geciktirebilir.
- Önceki etkinliğe kolayca geçmek için bir kısayol uygulamalıdır.
- Recents işlev tuşu iki kez dokunduğunda, en son kullanılan iki uygulama arasındaki hızlı anahtar eylemini tetiklemelidir.
- Recents işlevi tuşuna uzun süre basıldığında, desteklenirse, bölünmüş ekran çoklu güzergah modunu tetiklemelidir.
- Bağlı Recents'i birlikte hareket eden bir grup olarak görüntüleyebilir.
- [SR-1], genel bakış ekranı için yukarı akış Android kullanıcı arayüzünü (veya benzer bir küçük resim tabanlı arabirim) kullanmanız şiddetle tavsiye edilir.
3.8.9. Giriş Yönetimi
Android, üçüncü taraf giriş yöntemi editörleri için giriş yönetimi ve desteği için destek içerir.
Cihaz uygulamaları kullanıcıların aygıtta üçüncü taraf giriş yöntemlerini kullanmalarına izin veriyorsa, bunlar:
- [C-1] android.software.input_methods platform özelliğini bildirmeli ve Android SDK belgelerinde tanımlandığı gibi IME API'lerini desteklemelidir.
3.8.10. Kilit Ekranı Medya Kontrolü
Uzaktan kumanda istemcisi API, medya uygulamalarının kilit ekranında görüntülenen oynatma kontrolleriyle entegre olmasını sağlayan medya bildirim şablonu lehine Android 5.0'dan kullanımdan kaldırılmıştır.
3.8.11. Ekran Koruyucular (daha önce hayaller)
Ekran Koruyucuları Congfigure yapmak amacıyla ayarlar için Bölüm 3.2.3.5'e bakın.
3.8.12. Konum
Cihaz uygulamaları, konum koordinatlarını sağlayabilen bir donanım sensörü (örn. GPS) içeriyorsa, bunlar
- [C-1-2], ayarlar içindeki konum menüsündeki mevcut konum durumunu görüntülemelidir.
- [C-1-3] Ayarlar içindeki Konum menüsünde konum modlarını görüntülememelidir.
3.8.13. Unicode ve Yazı Tipi
Android, Unicode 10.0'da tanımlanan emoji karakterleri için destek içerir.
Cihaz uygulamaları bir ekran veya video çıktısı içeriyorsa, bunlar:
- [C-1] bu emoji karakterlerini renk glifinde oluşturabilmelidir.
- [C-1-2] aşağıdakileri desteklemelidir:
- Farklı ağırlıklara sahip Roboto 2 yazı tipi-Sans-serif-ince, sans-serif-ışık, sans-serif-medium, sans-serif-black, sans-serif-condensed, sans-serif-serif-condensed ışığı cihaz.
- Latin genişletilmiş A, B, C ve D aralıkları ve Unicode 7.0'ın para birimi sembolleri bloğundaki tüm glifler dahil olmak üzere Latin, Yunan ve Kiril'in tam Unicode 7.0 kapsamı.
- [C-1-3] Sistem görüntüsünde Notocoloremoji.tff'i kaldırmamalı veya değiştirmemelidir. (Notocoloremoji.tff içinde emoji'yi geçersiz kılmak için yeni bir emoji yazı tipi eklemek kabul edilebilir)
- Unicode Teknik Raporu #51'de belirtildiği gibi cilt tonunu ve çeşitli aile emojilerini desteklemelidir.
Cihaz uygulamaları bir IME içeriyorsa, bunlar:
- Bu emoji karakterleri için kullanıcıya bir giriş yöntemi sağlamalıdır.
Android, Myanmar yazı tiplerini oluşturmak için destek içerir. Myanmar, Myanmar dillerini oluşturmak için yaygın olarak “Zawgyi” olarak bilinen unicode uyumlu olmayan birkaç yazı tipine sahiptir.
Cihaz uygulamaları Birmanya için destek içeriyorsa, bunlar:
- [C-2-1] Unicode Uyumlu Yazı Tipi ile metni varsayılan olarak oluşturmalıdır; Kullanıcı dil seçicide seçmedikçe unicode olmayan uyumlu yazı tipi varsayılan yazı tipi olarak ayarlanmamalıdır.
- [C-2-2] cihazda unicode olmayan uyumlu bir yazı tipi desteklenirse, bir Unicode yazı tipini ve unicode uyumlu olmayan bir yazı tipini desteklemelidir. Unicode Olmayan Uyumlu Yazı Tipi, Unicode Yazı Tipini kaldırmamalı veya üzerine yazmamalıdır.
- [C-2-3], yalnızca komut dosyası Kodu olan bir dil kodu belirtilirse (örneğin My-qaag) unicode olmayan uyumlu yazı tipi ile metin oluşturmalıdır. Myanmar için unicode olmayan uyumlu yazı tipine atıfta bulunmak için başka hiçbir ISO dili veya bölge kodu (atanmış, atanmamış veya ayrılmış) kullanılamaz. Uygulama geliştiricileri ve web sayfası yazarları, My-QAAG'ı başka bir dil için olduğu gibi belirlenen dil kodu olarak belirleyebilirler.
3.8.14. Çoklu pencere
Cihaz uygulamaları aynı anda birden fazla etkinlik gösterme yeteneğine sahipse, bunlar:
- [C-1], Android SDK Multi Window Modu Destek belgesinde açıklanan uygulama davranışlarına ve API'lere uygun olarak bu tür çok pencere modlarını uygulamalı ve aşağıdaki gereksinimleri karşılamalıdır:
- [C-1-2]
android:resizeableActivity
AndroidManifest.xml
dosyasındaki bir uygulama tarafından bu SDK'da açıklandığı gibi ayarlanan ResizeAbleactivity'yi onurlandırmalıdır. - [C-1-3], ekran yüksekliği 440 dp'den az ve ekran genişliği 440 dp'den azsa bölünmüş ekran veya serbest biçimli modu sunmamalıdır.
- [C-1-4] Bir etkinlik, resimdeki resim dışındaki çoklu pencere modlarında 220dp'den küçük bir boyuta yeniden boyutlandırılmamalıdır.
- Ekran
xlarge
sahip cihaz uygulamaları FreeForm modunu desteklemelidir.
Cihaz uygulamaları çoklu pencere modlarını ve bölünmüş ekran modunu destekliyorsa, bunlar:
- [C-2-2], bölünmüş ekranlı çoklu pencerenin yerleştirilmiş aktivitesini kırpmalı, ancak başlatıcı uygulaması odaklanmış pencere ise bazı içeriğini göstermelidir.
- [C-2-3] Üçüncü Taraf Launcher uygulamasının beyan edilen
AndroidManifestLayout_minWidth
veAndroidManifestLayout_minHeight
değerlerini onurlandırmalı ve yanaşmış etkinliğin bazı içeriğini gösterme sırasında bu değerleri geçersiz kılmamalıdır.
Cihaz uygulamaları çoklu pencere modlarını ve resimdeki resim çoklu pencere modunu destekliyorsa, bunlar:
[C-3-1] Uygulama: Uygulama: Resim İçinde Resim Multi Window Modunda aktiviteleri başlatmalıdır:
- API Seviyesi 26 veya Daha Yüksek Hedefleme ve
android:supportsPictureInPicture
- API Seviye 25 veya Alt'ı Hedefleme ve Hem
android:resizeableActivity
veandroid:supportsPictureInPicture
.
- API Seviyesi 26 veya Daha Yüksek Hedefleme ve
[C-3-2]
setActions()
API'sı aracılığıyla geçerli PIP aktivitesi tarafından belirtildiği gibi SystemUI'larındaki eylemleri ortaya çıkarmalıdır.[C-3-3] 1: 2.39'dan daha büyük veya daha büyük ve
setAspectRatio()
API aracılığıyla PIP aktivitesi tarafından belirtildiği gibi 2.39: 1'e eşit veya daha az olan en boy oranlarını desteklemelidir.[C-3-4] PIP penceresini kontrol etmek için
KeyEvent.KEYCODE_WINDOW
kullanmalıdır; PIP modu uygulanmazsa, anahtar ön plan aktivitesinde kullanılabilir olmalıdır.[C-3-5], bir uygulamanın PIP modunda görüntülenmesini engellemek için bir kullanıcının uygunluğu sağlamalıdır; AOSP uygulaması, bildirim gölgesinde kontroller yaparak bu gereksinimi karşılamaktadır.
[C-3-6] Bir uygulama
AndroidManifestLayout_minWidth
veAndroidManifestLayout_minHeight
için herhangi bir değer beyan etmediğinde PIP penceresi için aşağıdaki minimum genişliği ve yüksekliği tahsis etmelidir:-
UI_MODE_TYPE_TELEVISION
dışında ayarlanan configuration.uimode ile cihazlar minimum genişlik ve yükseklik 108 dp tahsis edilmelidir. -
UI_MODE_TYPE_TELEVISION
olarak ayarlanan configuration.uimode ile cihazların minimum 240 dp genişliği ve minimum 135 dp yüksekliği tahsis etmesi gerekir.
-
3.8.15. Ekran Kesimi
Android, SDK belgesinde açıklandığı gibi bir ekran kesimini destekler. DisplayCutout
API, ekranın kenarında, bir ekran kesimi veya kenar (lar) ı kavisli ekran nedeniyle bir uygulama için işlevsel olmayabilecek bir alanı tanımlar.
Cihaz uygulamaları ekran kesme (ler) içeriyorsa, bunlar:
- Cihazın en boy oranı 1.0 (1: 1) ise [C-1-5] kesik (ler) olmamalıdır.
- [C-1-2] kenar başına birden fazla kesime sahip olmamalıdır.
- [C-1-3] SDK'da açıklandığı gibi
WindowManager.LayoutParams
API üzerinden uygulama tarafından belirlenen ekran kesme bayraklarını onurlandırmalıdır. - [C-1-4],
DisplayCutout
API'sinde tanımlanan tüm kesme metrikleri için doğru değerleri rapor etmelidir.
3.8.16. Cihaz Kontrolleri
Android, üçüncü taraf uygulamalarının kullanıcılar için hızlı durum ve eylem için cihaz kontrolleri yayınlamasına izin vermek için ControlsProviderService
ve Control
API'lerini içerir.
Cihaza özgü gereksinimler için bkz. Bölüm 2_2_3 .
3.9. Cihaz yönetimi
Android , Android Cihaz Yönetimi API'sı aracılığıyla şifre politikalarının uygulanması veya uzaktan silme işlemi gibi sistem düzeyinde güvenliğe duyarlı uygulamaların cihaz yönetimi işlevlerini gerçekleştirmesine izin veren özellikler içerir.
Cihaz uygulamaları, Android SDK belgelerinde tanımlanan tüm cihaz yönetim politikalarını uyguluyorsa, bunlar:
- [C-1]
android.software.device_admin
beyan etmelidir. - [C-1-2], Bölüm 3.9.1 ve Bölüm 3.9.1.1'de açıklandığı gibi cihaz sahibi sağlanmasını desteklemelidir.
3.9.1 Cihaz Sağlama
3.9.1.1 Cihaz Sahibi Sağlama
Cihaz uygulamaları android.software.device_admin
bildirirse,:
- [C-1], aşağıda açıklandığı gibi bir cihaz sahibi uygulaması olarak bir aygıt ilkesi istemcisinin (DPC) kaydettirilmesini desteklemelidir:
- Cihaz uygulamasının henüz yapılandırılmadığı zaman:
- [C-1-5] Cihaz,
android.hardware.nfc
özellikli özellik bayrağı aracılığıyla yakın alan iletişimleri (NFC) desteğini bildirirse ve mime türüMIME_TYPE_PROVISIONING_NFC
ile bir kayıt içeren bir NFC mesajı alırsa, DPC uygulamasını cihaz sahibi uygulaması olarak kaydetmelidir. . - [C-1-8] Action_get_provisioning_mode amacını, cihaz sahibi sağlama tetiklendikten sonra göndermelidir, böylece DPC uygulaması, yalnızca bir geçerli seçenek olduğu belirlenmedikçe bir cihaz sahibi veya profil sahibi olup olmayacağını seçebilir (sadece bir geçerli seçenek olduğu ( profil sahibi sağlanmasının desteklenmediği NFC tabanlı sunum gibi).
- [C-1-9], kullanılan sağlama yöntemine bakılmaksızın, sağlama sırasında bir cihaz sahibi kurulmuşsa, cihaz sahibi uygulamasına action_admin_policy_compliance amacını göndermelidir. Cihaz sahibi uygulaması bitene kadar kullanıcı kurulum sihirbazında ilerleyememelidir.
- [C-1-5] Cihaz,
- Cihaz uygulamasının kullanıcı verileri olduğunda,:
- [C-1-7], cihaz sahibi uygulaması olarak herhangi bir DPC uygulamasını artık kaydetmemelidir.
- Cihaz uygulamasının henüz yapılandırılmadığı zaman:
- [C-1-2], cihaz sahibi olarak belirlenen uygulamayı kabul etmek için sağlama işleminden önce veya sunum sırasında bazı olumlu eylemler gerektirmelidir. Onay kullanıcı eylemi veya bazı programlı yollarla olabilir, ancak cihaz sahibi sağlanması başlatılmadan önce uygun açıklama bildirimi (AOSP'de referans verildiği gibi) gösterilmelidir. Ayrıca, cihaz sahibi sağlama için kullanılan programlı cihaz sahibi onay mekanizması (işletmeler tarafından), girişim dışı kullanım için kutu dışı deneyime müdahale etmemelidir.
- [C-1-3] rızayı zor kodlamamalı veya diğer cihaz sahibi uygulamalarının kullanılmasını önlememelidir.
Cihaz uygulamaları android.software.device_admin
beyan ediyorsa, ancak aynı zamanda tescilli bir cihaz sahibi yönetimi çözümü ekleyin ve çözümlerinde standart "aygıt sahibi" olarak "cihaz sahibi eşdeğeri" olarak yapılandırılmış bir uygulamayı tanıtmak için bir mekanizma sağlayın. Android CihazPolicyManager APIS, onlar:
- [C-2-1], tanıtılan belirli uygulamanın meşru bir kurumsal cihaz yönetimi çözümüne ait olduğunu doğrulamak için bir süreç olmalı ve haklara eşdeğeri "cihaz sahibi" olarak sahip olması için tescilli çözümde zaten yapılandırılmış olmalıdır. .
- [C-2-2], DPC uygulamasını "Cihaz Sahibi" olarak kaydettirmeden önce
android.app.action.PROVISION_MANAGED_DEVICE
tarafından başlatılan akışla aynı AOSP cihazı sahibi onay açıklamasını göstermelidir. - DPC uygulamasını "Cihaz Sahibi" olarak kaydettirmeden önce cihazda kullanıcı verileri olabilir.
3.9.1.2 Yönetilen Profil Sağlama
Cihaz uygulamaları android.software.managed_users
bildirirse,:
[C-1] API'lerin bir Aygıt İlkesi Denetleyicisi (DPC) uygulamasına izin veren yeni bir yönetilen profilin sahibi olmasına izin vermelidir.
[C-1-2] Yönetilen profil sağlama işlemi ( Android.Apciaction.Action.Provision_Managed_Profile kullanılarak DPC tarafından başlatılan akış) veya platform), onay ekranı ve kullanıcı deneyimi AOSP uygulamasıyla uyumlu olmalıdır.
[C-1-3], belirli bir sistem işlevinin aygıt ilkesi denetleyicisi (DPC) tarafından devre dışı bırakıldığını belirtmek için ayarlar içinde aşağıdaki kullanıcı uygunluklarını sağlamalıdır:
- Belirli bir ayarın bir aygıt yöneticisi tarafından kısıtlandığında temsil edilecek tutarlı bir simge veya başka bir kullanıcı uygunluğu (örneğin yukarı akış AOSP bilgi simgesi).
-
setShortSupportMessage
aracılığıyla aygıt yöneticisi tarafından sağlanan kısa bir açıklama mesajı. - DPC uygulamasının simgesi.
[C-1-4] Android.App.Action.Provision_Managed_Profile Niyeti tarafından sağlandığında bir profil sahibi kurulursa, iş profilinde Action_provisioning_successful Niyet için işleyiciyi başlatmalıdır ve DPC işleyiciyi uygulamıştır.
[C-1-5] Android.App.Action.Provision_Managed_Profile Niyet tarafından başlatıldığında, DPC iş profiline Action_profile_provisioning_complete yayını göndermelidir.
[C-1-6] Action_get_provisioning_mode amacını, profil sahibi sağlama tetiklendikten sonra göndermelidir, böylece DPC uygulaması, bir cihaz sahibi veya profil sahibi olmak için bir cihaz sahibi veya profil sahibi olmak isteyebilir, öngörme tarafından tetiklenirken yürütülmeyi seçebilir. .
[C- 1-7 ], Procation_admin_policy_complianciance niyetini iş profiline göndermelidir. Profil sahibi uygulaması bitene kadar kullanıcı kurulum sihirbazında ilerlememelidir.
[C-1-8], kullanılan sağlama yöntemine bakılmaksızın, bir profil sahibi kurulduğunda kişisel profil DPC'ye Action_managed_profile_provisioned yayın göndermelidir.
3.9.2 Yönetilen Profil Desteği
Cihaz uygulamaları android.software.managed_users
bildirirse,:
- [C-1],
android.app.admin.DevicePolicyManager
API'leri aracılığıyla yönetilen profilleri desteklemelidir. - [C-1-2] bir ve sadece bir yönetilen profilin oluşturulmasına izin vermelidir.
- [C-1-3], yönetilen uygulamaları ve widget'ları ve Recents ve Bildirimler gibi diğer rozetli kullanıcı arayüzlerini temsil etmek için bir simge rozeti (AOSP yukarı akış çalışma rozetine benzer) kullanmalıdır.
- [C-1-4], kullanıcının yönetilen bir profil uygulaması içinde ne zaman olduğunu belirtmek için bir bildirim simgesi (AOSP yukarı akış çalışma rozetine benzer) görüntülemelidir.
- [C-1-6] Yönetilen bir profilin olduğu durumlarda, kullanıcının yönetilen profilden birincil kullanıcıya iletmesine izin vermek için 'seçici' niyetinde görsel bir uygunluk göstermelidir, ancak aygıt ilkesi tarafından etkinleştirilirse Denetleyici.
- [C-1-7] Yönetilen bir profilin bulunduğu durumlarda, hem birincil kullanıcı hem de yönetilen profil için aşağıdaki kullanıcının uygunluklarını ortaya çıkarmalıdır:
- Birincil kullanıcı ve yönetilen profil için pil, konum, mobil veriler ve depolama kullanımı için ayrı muhasebe.
- Birincil kullanıcı veya yönetilen profil içinde yüklenen VPN uygulamalarının bağımsız yönetimi.
- Birincil kullanıcı veya yönetilen profil içine yüklenen uygulamaların bağımsız yönetimi.
- Birincil kullanıcı veya yönetilen profil içindeki hesapların bağımsız yönetimi.
- [C-1-8] Önceden yüklenmiş çeviricinin, kişilerin ve mesajlaşma uygulamalarının, aygıt ilkesi denetleyicisi izin verirse, birincil profilden olanlarla birlikte yönetilen profilden (biri varsa) arayan bilgileri arayabileceğini ve arayabilmesini sağlamalıdır.
- [C-1-9], yönetilen profil, birincil kullanıcıya ek olarak başka bir kullanıcı olarak sayılmamış olsa bile, birden fazla kullanıcı etkinleştirilmiş (bkz. Bölüm 9.5 ) bir cihaz için geçerli tüm güvenlik gereksinimlerini karşılamasını sağlamalıdır.
Cihaz uygulamaları android.software.managed_users
ve android.software.secure_lock_screen
bildirirse,:
- [C-2-1], yalnızca yönetilen bir profilde çalışan uygulamalara erişim vermek için aşağıdaki gereksinimleri karşılayan ayrı bir kilit ekranı belirleme olanağını desteklemelidir.
- Cihaz uygulamaları,
DevicePolicyManager.ACTION_SET_NEW_PASSWORD
niyetini onurlandırmalı ve yönetilen profil için ayrı bir kilit ekranı kimlik bilgisi yapılandırmak için bir arabirim göstermelidir. - Yönetilen profilin kilit ekranı kimlik bilgileri , Android Açık Kaynak Proje sitesinde belgelendiği gibi üst profil ile aynı kimlik bilgisi depolama ve yönetim mekanizmalarını kullanmalıdır.
- DPC şifre politikaları, GetParentProfileInstance tarafından döndürülen
DevicePolicyManager
örneğine çağrılmadığı sürece yalnızca yönetilen profilin kilit ekranı kimlik bilgileri için geçerli olmalıdır.
- Cihaz uygulamaları,
- Yönetilen profilden gelen kişiler önceden yüklenmiş çağrı günlüğü, çağrı içi kullanıcı arayüzünde, devam eden ve kaçırılan arama bildirimlerinde, kişiler ve mesajlaşma uygulamalarında görüntülendiğinde, yönetilen profil uygulamalarını belirtmek için kullanılan aynı rozetle rozlanmalıdır.
3.9.3 Yönetilen Kullanıcı Desteği
Cihaz uygulamaları android.software.managed_users
bildirirse,:
- [C-1], mevcut kullanıcıdan çıkış yapmak için bir kullanıcının karşılığını vermeli ve
isLogoutEnabled
true
döndürdüğünde çoklu kullanıcı oturumunda birincil kullanıcıya geri dönmelidir. Cihazın kilidini açmadan kullanıcının uygunluğuna kilit ekranından erişilebilir olmalıdır.
Cihaz uygulamaları android.software.device_admin
bildirirse ve ek ikincil kullanıcılar eklemek için cihaz üzerine bir kullanıcı uygunluğu sağlarsa, bunlar:
- [C-SR-1], yeni ikincil kullanıcıya hesapların eklenmesine izin vermeden önce, Android.App.Action.Provision_managed_Device tarafından başlatılan akışta gösterilen aynı AOSP cihazı sahibi onay açıklamalarını güçlü bir şekilde gösterin. cihazın yönetildiğini.
3.10. Ulaşılabilirlik
Android, engelli kullanıcıların cihazlarında daha kolay gezinmelerine yardımcı olan bir erişilebilirlik katmanı sağlar. Buna ek olarak, Android, erişilebilirlik hizmeti uygulamalarının kullanıcı ve sistem olayları için geri arama almasını ve metin-konuşma, dokunsal geri bildirim ve Trackball/D-Pad navigasyonu gibi alternatif geri bildirim mekanizmaları oluşturmasını sağlayan platform API'leri sağlar.
Cihaz uygulamaları üçüncü taraf erişilebilirlik hizmetlerini destekliyorsa, bunlar:
- [C-1] , APSUNABLE APIS SDK dokümantasyonunda açıklandığı gibi Android Erişilebilirlik Çerçevesinin uygulanmasını sağlamalıdır.
- [C-1-2] erişilebilirlik olayları oluşturmalı ve SDK'da belgelendiği gibi tüm kayıtlı
AccessibilityService
uygulamalarına uygunAccessibilityEvent
sunmalıdır. - [C-1-4], erişilebilirlikServiceInfo.flag_request_accessibility_button'u bildiren erişilebilirlik hizmetlerini kontrol etmek için bir kullanıcının uygunluğu sağlamalıdır. Bir sistem gezinme çubuğuna sahip cihaz uygulamaları için, kullanıcının bu hizmetleri kontrol etmek için sistemin gezinme çubuğunda bir düğme seçeneğine sahip olmasına izin vermesi gerektiğini unutmayın.
Cihaz uygulamaları önceden yüklenmiş erişilebilirlik hizmetleri içeriyorsa, bunlar:
- [C-2-1], veri depolama dosya tabanlı şifreleme (FBE) ile şifrelendiğinde bu önceden yüklenmiş erişilebilirlik hizmetlerini doğrudan önyükleme farkında uygulamaları olarak uygulamalıdır.
- Kullanıcıların ilgili erişilebilirlik hizmetlerini etkinleştirmesi için kutu dışı kurulum akışında bir mekanizma ve yazı tipi boyutunu, görüntüleme boyutunu ve büyütme hareketlerini ayarlama seçenekleri sağlamalıdır.
3.11. Konuşma metni
Android, uygulamaların metin-konuşma (TTS) hizmetlerinden yararlanmasına izin veren ve servis sağlayıcıların TTS hizmetlerinin uygulamalarını sunmasına izin veren API'ler içerir.
Android.hardware.audio.utput özelliğini bildiren cihaz uygulamaları: bunlar:
- [C-1] , Android TTS Framework API'lerini desteklemelidir.
Cihaz uygulamaları üçüncü taraf TTS motorlarının kurulumunu destekliyorsa, bunlar:
- [C-2-1], kullanıcının sistem düzeyinde kullanılmak üzere bir TTS motoru seçmesine izin vermek için kullanıcı uygunluğu sağlamalıdır.
3.12. TV giriş çerçevesi
Android Televizyon Giriş Çerçevesi (TIF), canlı içeriğin Android televizyon cihazlarına teslimatını basitleştirir. TIF, Android televizyon cihazlarını kontrol eden giriş modülleri oluşturmak için standart bir API sağlar.
Cihaz uygulamaları TIF'i destekliyorsa,:
- [C-1]
android.software.live_tv
platform özelliğini bildirmelidir. - [C-1-2] tüm TIF API'lerini, bu API'leri kullanan bir uygulama ve üçüncü taraf TIF tabanlı giriş hizmeti kurulabilir ve cihaza kullanılabilir.
3.13. Hızlı Ayarlar
Android, sık kullanılan veya acilen ihtiyaç duyulan eylemlere hızlı erişim sağlayan hızlı ayarlar kullanıcı arayüzü sağlar.
Cihaz uygulamaları hızlı ayarlar kullanıcı arayüzü içeriyorsa ve üçüncü taraf hızlı ayarları destekliyorsa, bunlar:
- [C-1], kullanıcının
quicksettings
API'leri aracılığıyla sağlanan fayansları bir üçüncü taraf uygulamasından eklemesine veya kaldırmasına izin vermelidir. - [C-1-2] üçüncü taraf uygulamasından doğrudan hızlı ayarlara bir karo eklememelidir.
- [C-1-3], sistem tarafından sağlanan hızlı ayar karolarının yanı sıra üçüncü taraf uygulamalardan tüm kullanıcı tarafından eklenmiş karoları göstermelidir.
3.14. Medya kullanıcı arayüzü
Cihaz uygulamaları, MediaBrowser
veya MediaSession
aracılığıyla üçüncü taraf uygulamalarla etkileşime giren sesle aktif olmayan uygulamaları (uygulamalar) içeriyorsa, uygulamalar:
[C-1-2],
MediaDescription
tarif edildiği gibi GetIconBitMap () veya GetIConuri () ve GetTitle () aracılığıyla elde edilen başlıklar ile elde edilen simgeleri açıkça göstermelidir. Güvenlik düzenlemelerine uymak için başlıkları kısaltabilir (örneğin sürücü dikkat dağıtıcı).[C-1-3], bu üçüncü taraf uygulamanın sağladığı içeriği görüntülerken üçüncü taraf uygulama simgesini göstermelidir.
[C-1-4], kullanıcının tüm
MediaBrowser
hiyerarşisiyle etkileşime girmesine izin vermelidir. Güvenlik düzenlemelerine uymak için hiyerarşinin bir kısmına erişimi kısıtlayabilir (örneğin sürücü dikkat dağıtma), ancak içerik veya içerik sağlayıcısına dayalı tercihli tedavi vermemelidir.[C-1-5]
MediaSession.Callback#onMediaButtonEvent
içinKEYCODE_HEADSETHOOK
veyaKEYCODE_MEDIA_PLAY_PAUSE
çift TAP'siniKEYCODE_MEDIA_NEXT
olarak düşünmelidir.
3.15. Anında Uygulamalar
Cihaz uygulamaları anlık uygulamaları destekliyorsa, aşağıdaki gereksinimleri karşılamalıdırlar:
- [C-1-1] Anlık uygulamalara yalnızca
android:protectionLevel
"instant"
olarak ayarlanan izinler verilmelidir. - [C-1-2] Anında uygulamalar, aşağıdakilerden biri doğru olmadıkça, örtük niyet yoluyla yüklü uygulamalarla etkileşime girmemelidir:
- Bileşenin niyet desen filtresi açıktır ve category_browable'a sahiptir
- Eylem Action_Send, Action_Sendto, Action_Send_Multiple
- Hedef açıkça Android ile maruz kaldı: VisebletoInstantApps
- [C-1-3] Anında uygulamalar, bileşen Android: VisebletoInstantApps aracılığıyla ortaya çıkmadıkça yüklü uygulamalarla açıkça etkileşime girmemelidir.
- [C-1-4] Yüklü uygulamalar, anında uygulama yüklü uygulamaya açıkça bağlanmadıkça cihazdaki anlık uygulamalar hakkında ayrıntıları görmemelidir.
Cihaz uygulamaları, anlık uygulamalarla etkileşim kurmak için aşağıdaki kullanıcı karşılamalarını sağlamalıdır. AOSP, varsayılan sistem kullanıcı arayüzü, ayarlar ve başlatıcı ile gereksinimleri karşılar. Cihaz uygulamaları:
- [C-1-5], her bir uygulama paketi için yerel olarak önbelleğe alınan anlık uygulamaları görüntülemek ve silmek için bir kullanıcının uygunluğu sağlamalıdır.
- [C-1-6] ön planda çalışırken çökebilecek kalıcı bir kullanıcı bildirimi sağlamalıdır. Bu kullanıcı bildirimi, anlık uygulamaların yükleme gerektirmediğini ve kullanıcıyı Ayarlardaki Uygulama Bilgileri ekranına yönlendiren bir kullanıcı uygunluğu sağlamalıdır. Web niyetleri aracılığıyla başlatılan anlık uygulamalar için,
Intent.ACTION_VIEW
için bir eylem ile ve "HTTP" veya "HTTPS" şeması ile tanımlandığı gibi, ek bir kullanıcı uygunluğu kullanıcının anlık uygulamayı başlatmamasına ve başlatmamasına izin vermelidir. the associated link with the configured web browser, if a browser is available on the device. - [C-1-7] MUST allow running Instant Apps to be accessed from the Recents function if the Recents function is available on the device.
[C-1-8] MUST preload one or more applications or service components with an intent handler for the intents listed in the SDK here and make the intents visible for Instant Apps.
3.16. Companion Device Pairing
Android includes support for companion device pairing to more effectively manage association with companion devices and provides the CompanionDeviceManager
API for apps to access this feature.
If device implementations support the companion device pairing feature, they:
- [C-1-1] MUST declare the feature flag
FEATURE_COMPANION_DEVICE_SETUP
. - [C-1-2] MUST ensure the APIs in the
android.companion
package is fully implemented. - [C-1-3] MUST provide user affordances for the user to select/confirm a companion device is present and operational.
3.17. Heavyweight Apps
If device implementations declare the feature FEATURE_CANT_SAVE_STATE
, then they:
- [C-1-1] MUST have only one installed app that specifies
cantSaveState
running in the system at a time. If the user leaves such an app without explicitly exiting it (for example by pressing home while leaving an active activity the system, instead of pressing back with no remaining active activities in the system), then device implementations MUST prioritize that app in RAM as they do for other things that are expected to remain running, such as foreground services. While such an app is in the background, the system can still apply power management features to it, such as limiting CPU and network access. - [C-1-2] MUST provide a UI affordance to chose the app that won't participate in the normal state save/restore mechanism once the user launches a second app declared with
cantSaveState
attribute. - [C-1-3] MUST NOT apply other changes in policy to apps that specify
cantSaveState
, such as changing CPU performance or changing scheduling prioritization.
If device implementations don't declare the feature FEATURE_CANT_SAVE_STATE
, then they:
- [C-1-1] MUST ignore the
cantSaveState
attribute set by apps and MUST NOT change the app behavior based on that attribute.
3.18. Kişiler
Android includes Contacts Provider
APIs to allow applications to manage contact information stored on the device. Contact data that is entered directly into the device is typically synchronized with a web service, but the data MAY also only reside locally on the device. Contacts that are only stored on the device are referred to as local contacts.
RawContacts are "associated with" or "stored in" an Account when the ACCOUNT_NAME
, and ACCOUNT_TYPE
, columns for the raw contacts match the corresponding Account.name and Account.type fields of the account.
Default local account : an account for raw contacts that are only stored on the device and not associated with an Account in the AccountManager , which are created with null values for the ACCOUNT_NAME
, and ACCOUNT_TYPE
, columns.
Custom local account : an account for raw contacts that are only stored on the device and not associated with an Account in the AccountManager, which are created with at least one non-null value for the ACCOUNT_NAME
, and ACCOUNT_TYPE
, columns.
Cihaz uygulamaları:
- [C-SR-1] Are STRONGLY RECOMMENDED to not create custom local accounts .
If device implementations use a custom local account :
- [C-1-1] The
ACCOUNT_NAME
, of the custom local account MUST be returned byContactsContract.RawContacts.getLocalAccountName
- [C-1-2] The
ACCOUNT_TYPE
, of the custom local account MUST be returned byContactsContract.RawContacts.getLocalAccountType
- [C-1-3] Raw contacts that are inserted by third party applications with the default local account (ie by setting null values for
ACCOUNT_NAME
andACCOUNT_TYPE
) MUST be inserted to the custom local account . - [C-1-4] Raw contacts inserted into the custom local account MUST not be removed when accounts are added or removed.
- [C-1-5] Delete operations performed against the custom local account MUST result in raw contacts being purged immediately (as if the
CALLER_IS_SYNCADAPTER
param was set to true), even if theCALLER\_IS\_SYNCADAPTER
param was set to false or not belirtildi.
4. Application Packaging Compatibility
Devices implementations:
- [C-0-1] MUST be capable of installing and running Android “.apk” files as generated by the “aapt” tool included in the official Android SDK .
- As the above requirement may be challenging, device implementations are RECOMMENDED to use the AOSP reference implementation's package management system.
Cihaz uygulamaları:
- [C-0-2] MUST support verifying “.apk” files using the APK Signature Scheme v3 , APK Signature Scheme v2 and JAR signing .
- [C-0-3] MUST NOT extend either the .apk , Android Manifest , Dalvik bytecode , or RenderScript bytecode formats in such a way that would prevent those files from installing and running correctly on other compatible devices.
[C-0-4] MUST NOT allow apps other than the current "installer of record" for the package to silently uninstall the app without any user confirmation, as documented in the SDK for the
DELETE_PACKAGE
permission. The only exceptions are the system package verifier app handling PACKAGE_NEEDS_VERIFICATION intent and the storage manager app handling ACTION_MANAGE_STORAGE intent.[C-0-5] MUST have an activity that handles the
android.settings.MANAGE_UNKNOWN_APP_SOURCES
intent.[C-0-6] MUST NOT install application packages from unknown sources, unless the app that requests the installation meets all the following requirements:
- It MUST declare the
REQUEST_INSTALL_PACKAGES
permission or have theandroid:targetSdkVersion
set at 24 or lower. - It MUST have been granted permission by the user to install apps from unknown sources.
- It MUST declare the
SHOULD provide a user affordance to grant/revoke the permission to install apps from unknown sources per application, but MAY choose to implement this as a no-op and return
RESULT_CANCELED
forstartActivityForResult()
, if the device implementation does not want to allow users to have this choice. However, even in such cases, they SHOULD indicate to the user why there is no such choice presented.[C-0-7] MUST display a warning dialog with the warning string that is provided through the system API
PackageManager.setHarmfulAppWarning
to the user before launching an activity in an application that has been marked by the same system APIPackageManager.setHarmfulAppWarning
as potentially zararlı.SHOULD provide a user affordance to choose to uninstall or launch an application on the warning dialog.
[C-0-8] MUST implement support for Incremental File System as documented here .
[C-0-9] MUST support verifying .apk files using the APK Signature Scheme v4 .
5. Multimedia Compatibility
Cihaz uygulamaları:
- [C-0-1] MUST support the media formats, encoders, decoders, file types, and container formats defined in section 5.1 for each and every codec declared by
MediaCodecList
. - [C-0-2] MUST declare and report support of the encoders, decoders available to third-party applications via
MediaCodecList
. - [C-0-3] MUST be able to properly decode and make available to third-party apps all the formats it can encode. This includes all bitstreams that its encoders generate and the profiles reported in its
CamcorderProfile
.
Cihaz uygulamaları:
- SHOULD aim for minimum codec latency, in others words, they
- SHOULD NOT consume and store input buffers and return input buffers only once processed.
- SHOULD NOT hold onto decoded buffers for longer than as specified by the standard (eg SPS).
- SHOULD NOT hold onto encoded buffers longer than required by the GOP structure.
All of the codecs listed in the section below are provided as software implementations in the preferred Android implementation from the Android Open Source Project.
Please note that neither Google nor the Open Handset Alliance make any representation that these codecs are free from third-party patents. Those intending to use this source code in hardware or software products are advised that implementations of this code, including in open source software or shareware, may require patent licenses from the relevant patent holders.
5.1. Media Codecs
5.1.1. Audio Encoding
See more details in 5.1.3. Audio Codecs Details .
If device implementations declare android.hardware.microphone
, they MUST support encoding the following audio formats and make them available to third-party apps:
- [C-1-1] PCM/WAVE
- [C-1-2] FLAC
- [C-1-3] Opus
All audio encoders MUST support:
- [C-3-1] PCM 16-bit native byte order audio frames via the
android.media.MediaCodec
API.
5.1.2. Audio Decoding
See more details in 5.1.3. Audio Codecs Details .
If device implementations declare support for the android.hardware.audio.output
feature, they must support decoding the following audio formats:
- [C-1-1] MPEG-4 AAC Profile (AAC LC)
- [C-1-2] MPEG-4 HE AAC Profile (AAC+)
- [C-1-3] MPEG-4 HE AACv2 Profile (enhanced AAC+)
- [C-1-4] AAC ELD (enhanced low delay AAC)
- [C-1-11] xHE-AAC (ISO/IEC 23003-3 Extended HE AAC Profile, which includes the USAC Baseline Profile, and ISO/IEC 23003-4 Dynamic Range Control Profile)
- [C-1-5] FLAC
- [C-1-6] MP3
- [C-1-7] MIDI
- [C-1-8] Vorbis
- [C-1-9] PCM/WAVE including high-resolution audio formats up to 24 bits, 192 kHz sample rate, and 8 channels. Note that this requirement is for decoding only, and that a device is permitted to downsample and downmix during the playback phase.
- [C-1-10] Opus
If device implementations support the decoding of AAC input buffers of multichannel streams (ie more than two channels) to PCM through the default AAC audio decoder in the android.media.MediaCodec
API, the following MUST be supported:
- [C-2-1] Decoding MUST be performed without downmixing (eg a 5.0 AAC stream must be decoded to five channels of PCM, a 5.1 AAC stream must be decoded to six channels of PCM).
- [C-2-2] Dynamic range metadata MUST be as defined in "Dynamic Range Control (DRC)" in ISO/IEC 14496-3, and the
android.media.MediaFormat
DRC keys to configure the dynamic range-related behaviors of the audio decoder. The AAC DRC keys were introduced in API 21, and are:KEY_AAC_DRC_ATTENUATION_FACTOR
,KEY_AAC_DRC_BOOST_FACTOR
,KEY_AAC_DRC_HEAVY_COMPRESSION
,KEY_AAC_DRC_TARGET_REFERENCE_LEVEL
andKEY_AAC_ENCODED_TARGET_LEVEL
. - [SR-1] It is STRONGLY RECOMMENDED that requirements C-2-1 and C-2-2 above are satisfied by all AAC audio decoders.
When decoding USAC audio, MPEG-D (ISO/IEC 23003-4):
- [C-3-1] Loudness and DRC metadata MUST be interpreted and applied according to MPEG-D DRC Dynamic Range Control Profile Level 1.
- [C-3-2] The decoder MUST behave according to the configuration set with the following
android.media.MediaFormat
keys:KEY_AAC_DRC_TARGET_REFERENCE_LEVEL
andKEY_AAC_DRC_EFFECT_TYPE
.
MPEG-4 AAC, HE AAC, and HE AACv2 profile decoders:
- MAY support loudness and dynamic range control using ISO/IEC 23003-4 Dynamic Range Control Profile.
If ISO/IEC 23003-4 is supported and if both ISO/IEC 23003-4 and ISO/IEC 14496-3 metadata are present in a decoded bitstream, then:
- ISO/IEC 23003-4 metadata SHALL take precedence.
All audio decoders MUST support outputting:
- [C-6-1] PCM 16-bit native byte order audio frames via the
android.media.MediaCodec
API.
5.1.3. Audio Codecs Details
Format/Codec | Detaylar | File Types/Container Formats to be supported |
---|---|---|
MPEG-4 AAC Profile (AAC LC) | Support for mono/stereo/5.0/5.1 content with standard sampling rates from 8 to 48 kHz. |
|
MPEG-4 HE AAC Profile (AAC+) | Support for mono/stereo/5.0/5.1 content with standard sampling rates from 16 to 48 kHz. |
|
MPEG-4 HE AACv2 Profile (enhanced AAC+) | Support for mono/stereo/5.0/5.1 content with standard sampling rates from 16 to 48 kHz. |
|
AAC ELD (enhanced low delay AAC) | Support for mono/stereo content with standard sampling rates from 16 to 48 kHz. |
|
USAC | Support for mono/stereo content with standard sampling rates from 7.35 to 48 kHz. | MPEG-4 (.mp4, .m4a) |
AMR-NB | 4.75 to 12.2 kbps sampled @ 8 kHz | 3GPP (.3gp) |
AMR-WB | 9 rates from 6.60 kbit/s to 23.85 kbit/s sampled @ 16 kHz, as defined at AMR-WB, Adaptive Multi-Rate - Wideband Speech Codec | 3GPP (.3gp) |
FLAC | For both encoder and decoder: at least Mono and Stereo modes MUST be supported. Sample rates up to 192 kHz MUST be supported; 16-bit and 24-bit resolution MUST be supported. FLAC 24-bit audio data handling MUST be available with floating point audio configuration. |
|
MP3 | Mono/Stereo 8-320Kbps constant (CBR) or variable bitrate (VBR) |
|
MİDİ | MIDI Type 0 and 1. DLS Version 1 and 2. XMF and Mobile XMF. Support for ringtone formats RTTTL/RTX, OTA, and iMelody |
|
Vorbis |
| |
PCM/WAVE | PCM codec MUST support 16-bit linear PCM and 16-bit float. WAVE extractor must support 16-bit, 24-bit, 32-bit linear PCM and 32-bit float (rates up to limit of hardware). Sampling rates MUST be supported from 8 kHz to 192 kHz. | WAVE (.wav) |
başyapıt | Decoding: Support for mono, stereo, 5.0 and 5.1 content with sampling rates of 8000, 12000, 16000, 24000, and 48000 Hz. Encoding: Support for mono and stereo content with sampling rates of 8000, 12000, 16000, 24000, and 48000 Hz. |
|
5.1.4. Image Encoding
See more details in 5.1.6. Image Codecs Details .
Device implementations MUST support encoding the following image encoding:
- [C-0-1] JPEG
- [C-0-2] PNG
- [C-0-3] WebP
If device implementations support HEIC encoding via android.media.MediaCodec
for media type MIMETYPE_IMAGE_ANDROID_HEIC
, they:
- [C-1-1] MUST provide a hardware-accelerated HEVC encoder codec that supports
BITRATE_MODE_CQ
bitrate control mode,HEVCProfileMainStill
profile and 512 x 512 px frame size.
5.1.5. Image Decoding
See more details in 5.1.6. Image Codecs Details .
Device implementations MUST support decoding the following image encoding:
- [C-0-1] JPEG
- [C-0-2] GIF
- [C-0-3] PNG
- [C-0-4] BMP
- [C-0-5] WebP
- [C-0-6] Raw
If device implementations support HEVC video decoding, they:
- [C-1-1] MUST support HEIF (HEIC) image decoding.
Image decoders that support a high bit-depth format (9+ bits per channel):
- [C-2-1] MUST support outputting an 8-bit equivalent format if requested by the application, for example, via the
ARGB_8888
config ofandroid.graphics.Bitmap
.
5.1.6. Image Codecs Details
Format/Codec | Detaylar | Supported File Types/Container Formats |
---|---|---|
JPEG | Base+progressive | JPEG (.jpg) |
GIF | GIF (.gif) | |
PNG | PNG (.png) | |
BMP | BMP (.bmp) | |
WebP | WebP (.webp) | |
Çiğ | ARW (.arw), CR2 (.cr2), DNG (.dng), NEF (.nef), NRW (.nrw), ORF (.orf), PEF (.pef), RAF (.raf), RW2 (.rw2), SRW (.srw) | |
HEIF | Image, Image collection, Image sequence | HEIF (.heif), HEIC (.heic) |
Image encoder and decoders exposed through the MediaCodec API
[C-1-1] MUST support YUV420 8:8:8 flexible color format (
COLOR_FormatYUV420Flexible
) throughCodecCapabilities
.[SR-1] STRONGLY RECOMMENDED to support RGB888 color format for input Surface mode.
[C-1-3] MUST support at least one of a planar or semiplanar YUV420 8:8:8 color format:
COLOR_FormatYUV420PackedPlanar
(equivalent toCOLOR_FormatYUV420Planar
) orCOLOR_FormatYUV420PackedSemiPlanar
(equivalent toCOLOR_FormatYUV420SemiPlanar
). They are STRONGLY RECOMMENDED to support both.
5.1.7. Video Codecs
- For acceptable quality of web video streaming and video-conference services, device implementations SHOULD use a hardware VP8 codec that meets the requirements .
If device implementations include a video decoder or encoder:
[C-1-1] Video codecs MUST support output and input bytebuffer sizes that accommodate the largest feasible compressed and uncompressed frame as dictated by the standard and configuration but also not overallocate.
[C-1-2] Video encoders and decoders MUST support YUV420 8:8:8 flexible color formats (
COLOR_FormatYUV420Flexible
) throughCodecCapabilities
.[C-1-3] Video encoders and decoders MUST support at least one of a planar or semiplanar YUV420 8:8:8 color format:
COLOR_FormatYUV420PackedPlanar
(equivalent toCOLOR_FormatYUV420Planar
) orCOLOR_FormatYUV420PackedSemiPlanar
(equivalent toCOLOR_FormatYUV420SemiPlanar
). They are STRONGLY RECOMMENDED to support both.[SR-1] Video encoders and decoders are STRONGLY RECOMMENDED to support at least one of a hardware optimized planar or semiplanar YUV420 8:8:8 color format (YV12, NV12, NV21 or equivalent vendor optimized format.)
[C-1-5] Video decoders that support a high bit-depth format (9+ bits per channel) MUST support outputting an 8-bit equivalent format if requested by the application. This MUST be reflected by supporting an YUV420 8:8:8 color format via
android.media.MediaCodecInfo
.
If device implementations advertise HDR profile support through Display.HdrCapabilities
, they:
- [C-2-1] MUST support HDR static metadata parsing and handling.
If device implementations advertise intra refresh support through FEATURE_IntraRefresh
in the MediaCodecInfo.CodecCapabilities
class, they:
- [C-3-1] MUST support the refresh periods in the range of 10 - 60 frames and accurately operate within 20% of configured refresh period.
Unless the application specifies otherwise using the KEY_COLOR_FORMAT
format key, video decoder implementations:
- [C-4-1] MUST default to the color format optimized for hardware display if configured using Surface output.
- [C-4-2] MUST default to a YUV420 8:8:8 color format optimized for CPU reading if configured to not use Surface output.
5.1.8. Video Codecs List
Format/Codec | Detaylar | File Types/Container Formats to be supported |
---|---|---|
H.263 |
| |
H.264 AVC | See section 5.2 and 5.3 for details |
|
H.265 HEVC | See section 5.3 for details |
|
MPEG-2 | Ana Profil |
|
MPEG-4 SP |
| |
VP8 | See section 5.2 and 5.3 for details |
|
VP9 | See section 5.3 for details |
|
5.1.9. Media Codec Security
Device implementations MUST ensure compliance with media codec security features as described below.
Android includes support for OMX, a cross-platform multimedia acceleration API, as well as Codec 2.0, a low-overhead multimedia acceleration API.
If device implementations support multimedia, they:
- [C-1-1] MUST provide support for media codecs either via OMX or Codec 2.0 APIs (or both) as in the Android Open Source Project and not disable or circumvent the security protections. This specifically does not mean that every codec MUST use either the OMX or Codec 2.0 API, only that support for at least one of these APIs MUST be available, and support for the available APIs MUST include the security protections present.
- [C-SR-1] Are STRONGLY RECOMMENDED to include support for Codec 2.0 API.
If device implementations do not support the Codec 2.0 API, they:
- [C-2-1] MUST include the corresponding OMX software codec from the Android Open Source Project (if it is available) for each media format and type (encoder or decoder) supported by the device.
- [C-2-2] Codecs that have names starting with "OMX.google." MUST be based on their Android Open Source Project source code.
- [C-SR-2] Are STRONGLY RECOMMENDED that the OMX software codecs run in a codec process that does not have access to hardware drivers other than memory mappers.
If device implementations support Codec 2.0 API, they:
- [C-3-1] MUST include the corresponding Codec 2.0 software codec from the Android Open Source Project (if it is available) for each media format and type (encoder or decoder) supported by the device.
- [C-3-2] MUST house the Codec 2.0 software codecs in the software codec process as provided in the Android Open Source Project to make it possible to more narrowly grant access to software codecs.
- [C-3-3] Codecs that have names starting with "c2.android." MUST be based on their Android Open Source Project source code.
5.1.10. Media Codec Characterization
If device implementations support media codecs, they:
- [C-1-1] MUST return correct values of media codec characterization via the
MediaCodecInfo
API.
Özellikle:
- [C-1-2] Codecs with names starting with "OMX." MUST use the OMX APIs and have names that conform to OMX IL naming guidelines.
- [C-1-3] Codecs with names starting with "c2." MUST use the Codec 2.0 API and have names that conform to Codec 2.0 naming guidelines for Android.
- [C-1-4] Codecs with names starting with "OMX.google." or "c2.android." MUST NOT be characterized as vendor or as hardware-accelerated.
- [C-1-5] Codecs that run in a codec process (vendor or system) that have access to hardware drivers other than memory allocators and mappers MUST NOT be characterized as software-only.
- [C-1-6] Codecs not present in the Android Open Source Project or not based on the source code in that project MUST be characterized as vendor.
- [C-1-7] Codecs that utilize hardware acceleration MUST be characterized as hardware accelerated.
- [C-1-8] Codec names MUST NOT be misleading. For example, codecs named "decoders" MUST support decoding, and those named "encoders" MUST support encoding. Codecs with names containing media formats MUST support those formats.
If device implementations support video codecs:
- [C-2-1] All video codecs MUST publish achievable frame rate data for the following sizes if supported by the codec:
SD (low quality) | SD (high quality) | HD 720p | HD 1080p | UHD | |
---|---|---|---|---|---|
Video çözünürlüğü |
|
|
| 1920 x 1080 px (other than MPEG4) | 3840 x 2160 px (HEVC, VP9) |
- [C-2-2] Video codecs that are characterized as hardware accelerated MUST publish performance points information. They MUST each list all supported standard performance points (listed in
PerformancePoint
API), unless they are covered by another supported standard performance point. - Additionally they SHOULD publish extended performance points if they support sustained video performance other than one of the standard ones listed.
5.2. Video Encoding
If device implementations support any video encoder and make it available to third-party apps, they:
- SHOULD NOT be, over two sliding windows, more than 15% over the bitrate between intraframe (I-frame) intervals.
- SHOULD NOT be more than 100% over the bitrate over a sliding window of 1 second.
If device implementations include an embedded screen display with the diagonal length of at least 2.5 inches or include a video output port or declare the support of a camera via the android.hardware.camera.any
feature flag, they:
- [C-1-1] MUST include the support of at least one of the VP8 or H.264 video encoders, and make it available for third-party applications.
- SHOULD support both VP8 and H.264 video encoders, and make it available for third-party applications.
If device implementations support any of the H.264, VP8, VP9 or HEVC video encoders and make it available to third-party applications, they:
- [C-2-1] MUST support dynamically configurable bitrates.
- SHOULD support variable frame rates, where video encoder SHOULD determine instantaneous frame duration based on the timestamps of input buffers, and allocate its bit bucket based on that frame duration.
If device implementations support the MPEG-4 SP video encoder and make it available to third-party apps, they:
- SHOULD support dynamically configurable bitrates for the supported encoder.
If device implementations provide hardware accelerated video or image encoders, and support one or more attached or pluggable hardware camera(s) exposed through the android.camera
APIs:
- [C-4-1] all hardware accelerated video and image encoders MUST support encoding frames from the hardware camera(s).
- SHOULD support encoding frames from the hardware camera(s) through all video or image encoders.
If device implementations provide HDR encoding, they:
- [C-SR-1] are STRONGLY RECOMMENDED to provide a plugin for the seamless transcoding API to convert from HDR format to SDR format.
5.2.1. H.263
If device implementations support H.263 encoders and make it available to third-party apps, they:
- [C-1-1] MUST support Baseline Profile Level 45.
- SHOULD support dynamically configurable bitrates for the supported encoder.
5.2.2. H.264
If device implementations support H.264 codec, they:
- [C-1-1] MUST support Baseline Profile Level 3. However, support for ASO (Arbitrary Slice Ordering), FMO (Flexible Macroblock Ordering) and RS (Redundant Slices) is OPTIONAL. Moreover, to maintain compatibility with other Android devices, it is RECOMMENDED that ASO, FMO and RS are not used for Baseline Profile by encoders.
- [C-1-2] MUST support the SD (Standard Definition) video encoding profiles in the following table.
- SHOULD support Main Profile Level 4.
- SHOULD support the HD (High Definition) video encoding profiles as indicated in the following table.
If device implementations report support of H.264 encoding for 720p or 1080p resolution videos through the media APIs, they:
- [C-2-1] MUST support the encoding profiles in the following table.
SD (Low quality) | SD (High quality) | HD 720p | HD 1080p | |
---|---|---|---|---|
Video çözünürlüğü | 320 x 240 px | 720 x 480 px | 1280 x 720 px | 1920 x 1080 px |
Video kare hızı | 20 fps | 30 fps | 30 fps | 30 fps |
Video bitrate | 384 Kbps | 2 Mbps | 4 Mbps | 10 Mb/sn |
5.2.3. VP8
If device implementations support VP8 codec, they:
- [C-1-1] MUST support the SD video encoding profiles.
- SHOULD support the following HD (High Definition) video encoding profiles.
- [C-1-2] MUST support writing Matroska WebM files.
- SHOULD provide a hardware VP8 codec that meets the WebM project RTC hardware coding requirements , to ensure acceptable quality of web video streaming and video-conference services.
If device implementations report support of VP8 encoding for 720p or 1080p resolution videos through the media APIs, they:
- [C-2-1] MUST support the encoding profiles in the following table.
SD (Low quality) | SD (High quality) | HD 720p | HD 1080p | |
---|---|---|---|---|
Video çözünürlüğü | 320 x 180 px | 640 x 360 px | 1280 x 720 px | 1920 x 1080 px |
Video kare hızı | 30 fps | 30 fps | 30 fps | 30 fps |
Video bitrate | 800 Kbps | 2 Mbps | 4 Mbps | 10 Mb/sn |
5.2.4. VP9
If device implementations support VP9 codec, they:
- [C-1-2] MUST support Profile 0 Level 3.
- [C-1-1] MUST support writing Matroska WebM files.
- [C-1-3] MUST generate CodecPrivate data.
- SHOULD support the HD decoding profiles as indicated in the following table.
- [C-SR-1] are STRONGLY RECOMMENDED to support the HD decoding profiles as indicated in the following table if there is a hardware encoder.
SD | HD 720p | HD 1080p | UHD | |
---|---|---|---|---|
Video çözünürlüğü | 720 x 480 px | 1280 x 720 px | 1920 x 1080 px | 3840 x 2160 px |
Video kare hızı | 30 fps | 30 fps | 30 fps | 30 fps |
Video bitrate | 1.6 Mbps | 4 Mbps | 5 Mb/sn | 20 Mb/sn |
If device implementations claim to support Profile 2 or Profile 3 through the Media APIs:
- Support for 12-bit format is OPTIONAL.
5.2.5. H.265
If device implementations support H.265 codec, they:
- [C-1-1] MUST support Main Profile Level 3.
- SHOULD support the HD encoding profiles as indicated in the following table.
- [C-SR-1] are STRONGLY RECOMMENDED to support the HD encoding profiles as indicated in the following table if there is a hardware encoder.
SD | HD 720p | HD 1080p | UHD | |
---|---|---|---|---|
Video çözünürlüğü | 720 x 480 px | 1280 x 720 px | 1920 x 1080 px | 3840 x 2160 px |
Video kare hızı | 30 fps | 30 fps | 30 fps | 30 fps |
Video bitrate | 1.6 Mbps | 4 Mbps | 5 Mb/sn | 20 Mb/sn |
5.3. Video Decoding
If device implementations support VP8, VP9, H.264, or H.265 codecs, they:
- [C-1-1] MUST support dynamic video resolution and frame rate switching through the standard Android APIs within the same stream for all VP8, VP9, H.264, and H.265 codecs in real time and up to the maximum resolution supported by each codec on the device.
5.3.1. MPEG-2
If device implementations support MPEG-2 decoders, they:
- [C-1-1] MUST support the Main Profile High Level.
5.3.2. H.263
If device implementations support H.263 decoders, they:
- [C-1-1] MUST support Baseline Profile Level 30 and Level 45.
5.3.3. MPEG-4
If device implementations with MPEG-4 decoders, they:
- [C-1-1] MUST support Simple Profile Level 3.
5.3.4. H.264
If device implementations support H.264 decoders, they:
- [C-1-1] MUST support Main Profile Level 3.1 and Baseline Profile. Support for ASO (Arbitrary Slice Ordering), FMO (Flexible Macroblock Ordering) and RS (Redundant Slices) is OPTIONAL.
- [C-1-2] MUST be capable of decoding videos with the SD (Standard Definition) profiles listed in the following table and encoded with the Baseline Profile and Main Profile Level 3.1 (including 720p30).
- SHOULD be capable of decoding videos with the HD (High Definition) profiles as indicated in the following table.
If the height that is reported by the Display.getSupportedModes()
method is equal or greater than the video resolution, device implementations:
- [C-2-1] MUST support the HD 720p video decoding profiles in the following table.
- [C-2-2] MUST support the HD 1080p video decoding profiles in the following table.
SD (Low quality) | SD (High quality) | HD 720p | HD 1080p | |
---|---|---|---|---|
Video çözünürlüğü | 320 x 240 px | 720 x 480 px | 1280 x 720 px | 1920 x 1080 px |
Video kare hızı | 30 fps | 30 fps | 60 fps | 30 fps (60 fps Television ) |
Video bitrate | 800 Kbps | 2 Mbps | 8 Mbps | 20 Mb/sn |
5.3.5. H.265 (HEVC)
If device implementations support H.265 codec, they:
- [C-1-1] MUST support the Main Profile Level 3 Main tier and the SD video decoding profiles as indicated in the following table.
- SHOULD support the HD decoding profiles as indicated in the following table.
- [C-1-2] MUST support the HD decoding profiles as indicated in the following table if there is a hardware decoder.
If the height that is reported by the Display.getSupportedModes()
method is equal to or greater than the video resolution, then:
- [C-2-1] Device implementations MUST support at least one of H.265 or VP9 decoding of 720, 1080 and UHD profiles.
SD (Low quality) | SD (High quality) | HD 720p | HD 1080p | UHD | |
---|---|---|---|---|---|
Video çözünürlüğü | 352 x 288 px | 720 x 480 px | 1280 x 720 px | 1920 x 1080 px | 3840 x 2160 px |
Video kare hızı | 30 fps | 30 fps | 30 fps | 30/60 fps (60 fps Television with H.265 hardware decoding ) | 60 fps |
Video bitrate | 600 Kbps | 1.6 Mbps | 4 Mbps | 5 Mb/sn | 20 Mb/sn |
If device implementations claim to support an HDR Profile through the Media APIs:
- [C-3-1] Device implementations MUST accept the required HDR metadata from the application, as well as support extracting and outputting the required HDR metadata from the bitstream and/or container.
- [C-3-2] Device implementations MUST properly display HDR content on the device screen or on a standard video output port (eg, HDMI).
5.3.6. VP8
If device implementations support VP8 codec, they:
- [C-1-1] MUST support the SD decoding profiles in the following table.
- SHOULD use a hardware VP8 codec that meets the requirements .
- SHOULD support the HD decoding profiles in the following table.
If the height as reported by the Display.getSupportedModes()
method is equal or greater than the video resolution, then:
- [C-2-1] Device implementations MUST support 720p profiles in the following table.
- [C-2-2] Device implementations MUST support 1080p profiles in the following table.
SD (Low quality) | SD (High quality) | HD 720p | HD 1080p | |
---|---|---|---|---|
Video çözünürlüğü | 320 x 180 px | 640 x 360 px | 1280 x 720 px | 1920 x 1080 px |
Video kare hızı | 30 fps | 30 fps | 30 fps (60 fps Television ) | 30 (60 fps Television ) |
Video bitrate | 800 Kbps | 2 Mbps | 8 Mbps | 20 Mb/sn |
5.3.7. VP9
If device implementations support VP9 codec, they:
- [C-1-1] MUST support the SD video decoding profiles as indicated in the following table.
- SHOULD support the HD decoding profiles as indicated in the following table.
If device implementations support VP9 codec and a hardware decoder:
- [C-2-1] MUST support the HD decoding profiles as indicated in the following table.
If the height that is reported by the Display.getSupportedModes()
method is equal to or greater than the video resolution, then:
- [C-3-1] Device implementations MUST support at least one of VP9 or H.265 decoding of the 720, 1080 and UHD profiles.
SD (Low quality) | SD (High quality) | HD 720p | HD 1080p | UHD | |
---|---|---|---|---|---|
Video çözünürlüğü | 320 x 180 px | 640 x 360 px | 1280 x 720 px | 1920 x 1080 px | 3840 x 2160 px |
Video kare hızı | 30 fps | 30 fps | 30 fps | 30 fps (60 fps Television with VP9 hardware decoding ) | 60 fps |
Video bitrate | 600 Kbps | 1.6 Mbps | 4 Mbps | 5 Mb/sn | 20 Mb/sn |
If device implementations claim to support VP9Profile2
or VP9Profile3
through the 'CodecProfileLevel' media APIs:
- Support for 12-bit format is OPTIONAL.
If device implementations claim to support an HDR Profile ( VP9Profile2HDR
, VP9Profile2HDR10Plus
, VP9Profile3HDR
, VP9Profile3HDR10Plus
) through the media APIs:
- [C-4-1] Device implementations MUST accept the required HDR metadata (
KEY_HDR_STATIC_INFO
for all HDR profiles, as well as 'KEY_HDR10_PLUS_INFO' for HDR10Plus profiles) from the application. They also MUST support extracting and outputting the required HDR metadata from the bitstream and/or container. - [C-4-2] Device implementations MUST properly display HDR content on the device screen or on a standard video output port (eg, HDMI).
5.3.8. Dolby Vision
If device implementations declare support for the Dolby Vision decoder through HDR_TYPE_DOLBY_VISION
, they:
- [C-1-1] MUST provide a Dolby Vision-capable extractor.
- [C-1-2] MUST properly display Dolby Vision content on the device screen or on a standard video output port (eg, HDMI).
- [C-1-3] MUST set the track index of backward-compatible base-layer(s) (if present) to be the same as the combined Dolby Vision layer's track index.
5.3.9. AV1
If device implementations support AV1 codec, they:
- [C-1-1] MUST support Profile 0 including 10-bit content.
5.4. Ses kaydı
While some of the requirements outlined in this section are listed as SHOULD since Android 4.3, the Compatibility Definition for future versions are planned to change these to MUST. Existing and new Android devices are STRONGLY RECOMMENDED to meet these requirements that are listed as SHOULD, or they will not be able to attain Android compatibility when upgraded to the future version.
5.4.1. Raw Audio Capture and Microphone Information
If device implementations declare android.hardware.microphone
, they:
[C-1-1] MUST allow capture of raw audio content with the following characteristics:
- Format : Linear PCM, 16-bit
- Sampling rates : 8000, 11025, 16000, 44100, 48000 Hz
- Channels : Mono
SHOULD allow capture of raw audio content with the following characteristics:
- Format : Linear PCM, 16-bit and 24-bit
- Sampling rates : 8000, 11025, 16000, 22050, 24000, 32000, 44100, 48000 Hz
- Channels : As many channels as the number of microphones on the device
[C-1-2] MUST capture at above sample rates without up-sampling.
[C-1-3] MUST include an appropriate anti-aliasing filter when the sample rates given above are captured with down-sampling.
SHOULD allow AM radio and DVD quality capture of raw audio content, which means the following characteristics:
- Format : Linear PCM, 16-bit
- Sampling rates : 22050, 48000 Hz
- Channels : Stereo
[C-1-4] MUST honor the
MicrophoneInfo
API and properly fill in information for the available microphones on device accessible to the third-party applications via theAudioManager.getMicrophones()
API, and the currently active microphones which are accessible to the third party applications via theAudioRecord.getActiveMicrophones()
andMediaRecorder.getActiveMicrophones()
APIs. If device implementations allow AM radio and DVD quality capture of raw audio content, they:[C-2-1] MUST capture without up-sampling at any ratio higher than 16000:22050 or 44100:48000.
[C-2-2] MUST include an appropriate anti-aliasing filter for any up-sampling or down-sampling.
5.4.2. Capture for Voice Recognition
If device implementations declare android.hardware.microphone
, they:
- [C-1-1] MUST capture
android.media.MediaRecorder.AudioSource.VOICE_RECOGNITION
audio source at one of the sampling rates, 44100 and 48000. - [C-1-2] MUST, by default, disable any noise reduction audio processing when recording an audio stream from the
AudioSource.VOICE_RECOGNITION
audio source. - [C-1-3] MUST, by default, disable any automatic gain control when recording an audio stream from the
AudioSource.VOICE_RECOGNITION
audio source. - SHOULD record the voice recognition audio stream with approximately flat amplitude versus frequency characteristics: specifically, ±3 dB, from 100 Hz to 4000 Hz.
- SHOULD record the voice recognition audio stream with input sensitivity set such that a 90 dB sound power level (SPL) source at 1000 Hz yields RMS of 2500 for 16-bit samples.
- SHOULD record the voice recognition audio stream so that the PCM amplitude levels linearly track input SPL changes over at least a 30 dB range from -18 dB to +12 dB re 90 dB SPL at the microphone.
- SHOULD record the voice recognition audio stream with total harmonic distortion (THD) less than 1% for 1 kHz at 90 dB SPL input level at the microphone.
If device implementations declare android.hardware.microphone
and noise suppression (reduction) technologies tuned for speech recognition, they:
- [C-2-1] MUST allow this audio effect to be controllable with the
android.media.audiofx.NoiseSuppressor
API. - [C-2-2] MUST uniquely identify each noise suppression technology implementation via the
AudioEffect.Descriptor.uuid
field.
5.4.3. Capture for Rerouting of Playback
The android.media.MediaRecorder.AudioSource
class includes the REMOTE_SUBMIX
audio source.
If device implementations declare both android.hardware.audio.output
and android.hardware.microphone
, they:
[C-1-1] MUST properly implement the
REMOTE_SUBMIX
audio source so that when an application uses theandroid.media.AudioRecord
API to record from this audio source, it captures a mix of all audio streams except for the following:-
AudioManager.STREAM_RING
-
AudioManager.STREAM_ALARM
-
AudioManager.STREAM_NOTIFICATION
-
5.4.4. Acoustic Echo Canceler
If device implementations declare android.hardware.microphone
, they:
- SHOULD implement an Acoustic Echo Canceler (AEC) technology tuned for voice communication and applied to the capture path when capturing using
AudioSource.VOICE_COMMUNICATION
If device implementations provides an Acoustic Echo Canceler which is inserted in the capture audio path when AudioSource.VOICE_COMMUNICATION
is selected, they:
- [C-SR-1] are STRONGLY_RECOMMENDED to declare this via AcousticEchoCanceler API method AcousticEchoCanceler.isAvailable()
- [C-SR-2] are STRONGLY_RECOMMENDED to allow this audio effect to be controllable with the AcousticEchoCanceler API.
- [C-SR-3] are STRONGLY_RECOMMENDED to uniquely identify each AEC technology implementation via the AudioEffect.Descriptor.uuid field.
5.4.5. Concurrent Capture
If device implementations declare android.hardware.microphone
,they MUST implement concurrent capture as described in this document . Özellikle:
- [C-1-1] MUST allow concurrent access to microphone by an accessibility service capturing with
AudioSource.VOICE_RECOGNITION
and at least one application capturing with anyAudioSource
. - [C-1-2] MUST allow concurrent access to microphone by a pre-installed application that holds an Assistant role and at least one application capturing with any
AudioSource
except forAudioSource.VOICE_COMMUNICATION
orAudioSource.CAMCORDER
. - [C-1-3] MUST silence the audio capture for any other application, except for an accessibility service, while an application is capturing with
AudioSource.VOICE_COMMUNICATION
orAudioSource.CAMCORDER
. However, when an app is capturing viaAudioSource.VOICE_COMMUNICATION
then another app can capture the voice call if it is a privileged (pre-installed) app with permissionCAPTURE_AUDIO_OUTPUT
. - [C-1-4] If two or more applications are capturing concurrently and if neither app has an UI on top, the one that started capture the most recently receives audio.
5.4.6. Microphone Gain Levels
If device implementations declare android.hardware.microphone
, they:
- SHOULD exhibit approximately flat amplitude-versus-frequency characteristics in the mid-frequency range: specifically ±3dB from 100 Hz to 4000 Hz for each and every microphone used to record the voice recognition audio source.
- SHOULD set audio input sensitivity such that a 1000 Hz sinusoidal tone source played at 90 dB Sound Pressure Level (SPL) yields a response with RMS of 2500 for 16 bit-samples (or -22.35 dB Full Scale for floating point/double precision samples) for each and every microphone used to record the voice recognition audio source.
- [C-SR-1] are STRONGLY RECOMMENDED to exhibit amplitude levels in the low frequency range: specifically from ±20 dB from 5 Hz to 100 Hz compared to the mid-frequency range for each and every microphone used to record the voice recognition audio kaynak.
- [C-SR-2] are STRONGLY RECOMMENDED to exhibit amplitude levels in the high frequency range: specifically from ±30 dB from 4000 Hz to 22 KHz compared to the mid-frequency range for each and every microphone used to record the voice recognition audio kaynak.
5.5. Audio Playback
Android includes the support to allow apps to playback audio through the audio output peripheral as defined in section 7.8.2.
5.5.1. Raw Audio Playback
If device implementations declare android.hardware.audio.output
, they:
[C-1-1] MUST allow playback of raw audio content with the following characteristics:
- Source formats : Linear PCM, 16-bit, 8-bit, float
- Channels : Mono, Stereo, valid multichannel configurations with up to 8 channels
- Sampling rates (in Hz) :
- 8000, 11025, 16000, 22050, 24000, 32000, 44100, 48000 at the channel configurations listed above
- 96000 in mono and stereo
5.5.2. Audio Effects
Android provides an API for audio effects for device implementations.
If device implementations declare the feature android.hardware.audio.output
, they:
- [C-1-1] MUST support the
EFFECT_TYPE_EQUALIZER
andEFFECT_TYPE_LOUDNESS_ENHANCER
implementations controllable through the AudioEffect subclassesEqualizer
andLoudnessEnhancer
. - [C-1-2] MUST support the visualizer API implementation, controllable through the
Visualizer
class. - [C-1-3] MUST support the
EFFECT_TYPE_DYNAMICS_PROCESSING
implementation controllable through the AudioEffect subclassDynamicsProcessing
. - SHOULD support the
EFFECT_TYPE_BASS_BOOST
,EFFECT_TYPE_ENV_REVERB
,EFFECT_TYPE_PRESET_REVERB
, andEFFECT_TYPE_VIRTUALIZER
implementations controllable through theAudioEffect
sub-classesBassBoost
,EnvironmentalReverb
,PresetReverb
, andVirtualizer
. - [C-SR-1] Are STRONGLY RECOMMENDED to support effects in floating-point and multichannel.
5.5.3. Audio Output Volume
Otomotiv cihaz uygulamaları:
- SHOULD allow adjusting audio volume separately per each audio stream using the content type or usage as defined by AudioAttributes and car audio usage as publicly defined in
android.car.CarAudioManager
.
5.5.4. Audio Offload
If device implementations support audio offload playback , they:
- [C-SR-1] Are STRONGLY RECOMMENDED to trim the played gapless audio content when specified by the AudioTrack gapless API and the media container for MediaPlayer.
5.6. Audio Latency
Audio latency is the time delay as an audio signal passes through a system. Many classes of applications rely on short latencies, to achieve real-time sound effects.
For the purposes of this section, use the following definitions:
- output latency . The interval between when an application writes a frame of PCM-coded data and when the corresponding sound is presented to environment at an on-device transducer or signal leaves the device via a port and can be observed externally.
- cold output latency . The time between starting an output stream and the presentation time of the first frame based on timestamps, when the audio output system has been idle and powered down prior to the request.
- continuous output latency . The output latency for subsequent frames, after the device is playing audio.
- input latency . The interval between when a sound is presented by environment to device at an on-device transducer or signal enters the device via a port and when an application reads the corresponding frame of PCM-coded data.
- lost input . The initial portion of an input signal that is unusable or unavailable.
- cold input latency . The time between starting the stream and when the first valid frame is received, when the audio input system has been idle and powered down prior to the request.
- continuous input latency . The input latency for subsequent frames, while the device is capturing audio.
- cold output jitter . The variability among separate measurements of cold output latency values.
- cold input jitter . The variability among separate measurements of cold input latency values.
- continuous round-trip latency . The sum of continuous input latency plus continuous output latency plus one buffer period. The buffer period allows time for the app to process the signal and time for the app to mitigate phase difference between input and output streams.
- OpenSL ES PCM buffer queue API . The set of PCM-related OpenSL ES APIs within Android NDK .
- AAudio native audio API . The set of AAudio APIs within Android NDK .
- Timestamp . A pair consisting of a relative frame position within a stream and the estimated time when that frame enters or leaves the audio processing pipeline on the associated endpoint. See also AudioTimestamp .
- kusur . A temporary interruption or incorrect sample value in the audio signal, typically caused by a buffer underrun for output, buffer overrun for input, or any other source of digital or analog noise.
- ortalama mutlak sapma . The average of the absolute value of the deviations from the mean for a set of values.
- tap-to-tone latency . The time between when the screen is tapped and when a tone generated as a result of that tap is heard on the speaker.
If device implementations declare android.hardware.audio.output
, they MUST meet or exceed the following requirements:
- [C-1-1] The output timestamp returned by AudioTrack.getTimestamp and
AAudioStream_getTimestamp
is accurate to +/- 2 ms. - [C-1-2] Cold output latency of 500 milliseconds or less.
If device implementations declare android.hardware.audio.output
they are STRONGLY RECOMMENDED to meet or exceed the following requirements:
- [C-SR-1] Cold output latency of 100 milliseconds or less over the speaker data path. Existing and new devices that run this version of Android are VERY STRONGLY RECOMMENDED to meet these requirements now. In a future platform release, we will require Cold output latency of 200 ms or less as a MUST.
- [C-SR-2] Tap-to-tone latency of 80 milliseconds or less.
- [C-SR-3] Minimize the cold output jitter.
- [C-SR-4] The output timestamp returned by AudioTrack.getTimestamp and
AAudioStream_getTimestamp
is accurate to +/- 1 ms.
If device implementations meet the above requirements, after any initial calibration, when using the AAudio native audio API, for continuous output latency and cold output latency over at least one supported audio output device, they are:
- [C-SR-5] STRONGLY RECOMMENDED to report low-latency audio by declaring
android.hardware.audio.low_latency
feature flag. - [C-SR-6] STRONGLY RECOMMENDED to meet the requirements for low-latency audio via the AAudio API.
- [C-SR-7] STRONGLY RECOMMENDED to ensure that for streams that return
AAUDIO_PERFORMANCE_MODE_LOW_LATENCY
fromAAudioStream_getPerformanceMode()
, the value returned byAAudioStream_getFramesPerBurst()
is less than or equal to the value returned byandroid.media.AudioManager.getProperty(String)
for property keyAudioManager.PROPERTY_OUTPUT_FRAMES_PER_BUFFER
.
If device implementations do not meet the requirements for low-latency audio via the AAudio native audio API, they:
- [C-2-1] MUST NOT report support for low-latency audio.
If device implementations include android.hardware.microphone
, they MUST meet these input audio requirements:
- [C-3-1] Limit the error in input timestamps, as returned by AudioRecord.getTimestamp or
AAudioStream_getTimestamp
, to +/- 2 ms. "Error" here means the deviation from the correct value. - [C-3-2] Cold input latency of 500 milliseconds or less.
If device implementations include android.hardware.microphone
, they are STRONGLY RECOMMENDED to meet these input audio requirements:
- [C-SR-8] Cold input latency of 100 milliseconds or less over the microphone data path. Existing and new devices that run this version of Android are VERY STRONGLY RECOMMENDED to meet these requirements now. In a future platform release we will require Cold input latency of 200 ms or less as a MUST.
- [C-SR-9] Continuous input latency of 30 milliseconds or less.
- [C-SR-10] Minimize the cold input jitter.
- [C-SR-11] Limit the error in input timestamps, as returned by AudioRecord.getTimestamp or
AAudioStream_getTimestamp
, to +/- 1 ms.
If device implementations declare android.hardware.audio.output
and android.hardware.microphone
, they:
- [C-SR-12] Are STRONGLY RECOMMENDED to have a Mean Continuous Round-Trip Latency of 50 milliseconds or less over 5 measurements, with a Mean Absolute Deviation less than 10 msec, over at least one supported path.
5.7. Network Protocols
Device implementations MUST support the media network protocols for audio and video playback as specified in the Android SDK documentation.
For each codec and container format that a device implementation is required to support, the device implementation:
[C-1-1] MUST support that codec or container over HTTP and HTTPS.
[C-1-2] MUST support the corresponding media segment formats as shown in the media segment formats table below over HTTP Live Streaming draft protocol, Version 7 .
[C-1-3] MUST support the corresponding RTSP payload formats as shown in the RTSP table below. For exceptions please see the table footnotes in section 5.1 .
Media Segment Formats
Segment formats | Referanslar) | Required codec support |
---|---|---|
MPEG-2 Transport Stream | ISO 13818 | Video codecs:
and MPEG-2. Audio codecs:
|
AAC with ADTS framing and ID3 tags | ISO 13818-7 | See section 5.1.1 for details on AAC and its variants |
WebVTT | WebVTT |
RTSP (RTP, SDP)
Profil ismi | Referanslar) | Required codec support |
---|---|---|
H264 AVC | RFC 6184 | See section 5.1.8 for details on H264 AVC |
MP4A-LATM | RFC 6416 | See section 5.1.3 for details on AAC and its variants |
H263-1998 | RFC 3551 RFC 4629 RFC 2190 | See section 5.1.8 for details on H263 |
H263-2000 | RFC 4629 | See section 5.1.8 for details on H263 |
AMR | RFC 4867 | See section 5.1.3 for details on AMR-NB |
AMR-WB | RFC 4867 | See section 5.1.3 for details on AMR-WB |
MP4V-ES | RFC 6416 | See section 5.1.8 for details on MPEG-4 SP |
mpeg4-generic | RFC 3640 | See section 5.1.3 for details on AAC and its variants |
MP2T | RFC 2250 | See MPEG-2 Transport Stream underneath HTTP Live Streaming for details |
5.8. Secure Media
If device implementations support secure video output and are capable of supporting secure surfaces, they:
- [C-1-1] MUST declare support for
Display.FLAG_SECURE
.
If device implementations declare support for Display.FLAG_SECURE
and support wireless display protocol, they:
- [C-2-1] MUST secure the link with a cryptographically strong mechanism such as HDCP 2.x or higher for the displays connected through wireless protocols such as Miracast.
If device implementations declare support for Display.FLAG_SECURE
and support wired external display, they:
- [C-3-1] MUST support HDCP 1.2 or higher for all external displays connected via a user-accessible wired port.
5.9. Musical Instrument Digital Interface (MIDI)
If device implementations report support for feature android.software.midi
via the android.content.pm.PackageManager
class, they:
[C-1-1] MUST support MIDI over all MIDI-capable hardware transports for which they provide generic non-MIDI connectivity, where such transports are:
- USB host mode, section 7.7
- MIDI over Bluetooth LE acting in central role, section 7.4.3
[C-1-2] MUST support the inter-app MIDI software transport (virtual MIDI devices)
[C-1-3] MUST include libamidi.so (native MIDI support)
SHOULD support MIDI over USB peripheral mode, section 7.7
5.10. Profesyonel Ses
If device implementations report support for feature android.hardware.audio.pro
via the android.content.pm.PackageManager class, they:
- [C-1-1] MUST report support for feature
android.hardware.audio.low_latency
. - [C-1-2] MUST have the continuous round-trip audio latency, as defined in section 5.6 Audio Latency , MUST be 20 milliseconds or less and SHOULD be 10 milliseconds or less over at least one supported path.
- [C-1-3] MUST include a USB port(s) supporting USB host mode and USB peripheral mode.
- [C-1-4] MUST report support for feature
android.software.midi
. - [C-1-5] MUST meet latencies and USB audio requirements using the AAudio native audio API.
- [C-1-6] MUST have Cold output latency of 200 milliseconds or less.
- [C-1-7] MUST have Cold input latency of 200 milliseconds or less.
- [C-SR-1] Are STRONGLY RECOMMENDED to meet latencies as defined in section 5.6 Audio Latency , of 20 milliseconds or less, over 5 measurements with a Mean Absolute Deviation less than 5 milliseconds over the speaker to microphone path.
- [C-SR-2] Are STRONGLY RECOMMENDED to meet the Pro Audio requirements for continuous round-trip audio latency, cold input latency and cold output latency and USB audio requirements using the AAudio native audio API over the MMAP path.
- [C-SR-3] Are STRONGLY RECOMMENDED to provide a consistent level of CPU performance while audio is active and CPU load is varying. This should be tested using the Android app SynthMark . SynthMark uses a software synthesizer running on a simulated audio framework that measures system performance. The SynthMark app needs to be run using the “Automated Test” option and achieve the following results:
- voicemark.90 >= 32 voices
- latencymark.fixed.little <= 15 msec
- latencymark.dynamic.little <= 50 msec
See the SynthMark documentation for an explanation of the benchmarks.
- SHOULD minimize audio clock inaccuracy and drift relative to standard time.
- SHOULD minimize audio clock drift relative to the CPU
CLOCK_MONOTONIC
when both are active. - SHOULD minimize audio latency over on-device transducers.
- SHOULD minimize audio latency over USB digital audio.
- SHOULD document audio latency measurements over all paths.
- SHOULD minimize jitter in audio buffer completion callback entry times, as this affects usable percentage of full CPU bandwidth by the callback.
- SHOULD provide zero audio glitches under normal use at reported latency.
- SHOULD provide zero inter-channel latency difference.
- SHOULD minimize MIDI mean latency over all transports.
- SHOULD minimize MIDI latency variability under load (jitter) over all transports.
- SHOULD provide accurate MIDI timestamps over all transports.
- SHOULD minimize audio signal noise over on-device transducers, including the period immediately after cold start.
- SHOULD provide zero audio clock difference between the input and output sides of corresponding end-points, when both are active. Examples of corresponding end-points include the on-device microphone and speaker, or the audio jack input and output.
- SHOULD handle audio buffer completion callbacks for the input and output sides of corresponding end-points on the same thread when both are active, and enter the output callback immediately after the return from the input callback. Or if it is not feasible to handle the callbacks on the same thread, then enter the output callback shortly after entering the input callback to permit the application to have a consistent timing of the input and output sides.
- SHOULD minimize the phase difference between HAL audio buffering for the input and output sides of corresponding end-points.
- SHOULD minimize touch latency.
- SHOULD minimize touch latency variability under load (jitter).
- SHOULD have a latency from touch input to audio output of less than or equal to 40 ms.
If device implementations meet all of the above requirements, they:
- [C-SR-4] STRONGLY RECOMMENDED to report support for feature
android.hardware.audio.pro
via theandroid.content.pm.PackageManager
class.
If device implementations include a 4 conductor 3.5mm audio jack, they:
- [C-2-1] MUST have a mean Continuous Round-trip Audio Latency, as defined in section 5.6 Audio Latency , of 20 milliseconds or less, over 5 measurements with a Mean Absolute Deviation less than 5 milliseconds over the audio jack path.
- [C-SR-5] STRONGLY RECOMMENDED to comply with section Mobile device (jack) specifications of the Wired Audio Headset Specification (v1.1) .
If device implementations omit a 4 conductor 3.5mm audio jack and include a USB port(s) supporting USB host mode, they:
- [C-3-1] MUST implement the USB audio class.
- [C-3-2] MUST have a mean Continuous Round-trip Audio Latency of 25 milliseconds or less, over 5 measurements with a Mean Absolute Deviation less than 5 milliseconds over the USB host mode port using USB audio class. (This can be measured using a USB-3.5mm adapter and an Audio Loopback Dongle, or using a USB audio interface with patch cables connecting the inputs to outputs).
- [C-SR-6] Are STRONGLY RECOMMENDED to support simultaneous I/O up to 8 channels each direction, 96 kHz sample rate, and 24-bit or 32-bit depth, when used with USB audio peripherals that also support these requirements.
- [C-SR-7] Are STRONGLY RECOMMENDED to meet this group of requirements using the AAudio native audio API over the MMAP path.
If device implementations include an HDMI port, they:
- SHOULD support output in stereo and eight channels at 20-bit or 24-bit depth and 192 kHz without bit-depth loss or resampling, in at least one configuration.
5.11. Capture for Unprocessed
Android includes support for recording of unprocessed audio via the android.media.MediaRecorder.AudioSource.UNPROCESSED
audio source. In OpenSL ES, it can be accessed with the record preset SL_ANDROID_RECORDING_PRESET_UNPROCESSED
.
If device implementations intent to support unprocessed audio source and make it available to third-party apps, they:
[C-1-1] MUST report the support through the
android.media.AudioManager
property PROPERTY_SUPPORT_AUDIO_SOURCE_UNPROCESSED .[C-1-2] MUST exhibit approximately flat amplitude-versus-frequency characteristics in the mid-frequency range: specifically ±10dB from 100 Hz to 7000 Hz for each and every microphone used to record the unprocessed audio source.
[C-1-3] MUST exhibit amplitude levels in the low frequency range: specifically from ±20 dB from 5 Hz to 100 Hz compared to the mid-frequency range for each and every microphone used to record the unprocessed audio source.
[C-1-4] MUST exhibit amplitude levels in the high frequency range: specifically from ±30 dB from 7000 Hz to 22 KHz compared to the mid-frequency range for each and every microphone used to record the unprocessed audio source.
[C-1-5] MUST set audio input sensitivity such that a 1000 Hz sinusoidal tone source played at 94 dB Sound Pressure Level (SPL) yields a response with RMS of 520 for 16 bit-samples (or -36 dB Full Scale for floating point/double precision samples) for each and every microphone used to record the unprocessed audio source.
[C-1-6] MUST have a signal-to-noise ratio (SNR) at 60 dB or higher for each and every microphone used to record the unprocessed audio source. (whereas the SNR is measured as the difference between 94 dB SPL and equivalent SPL of self noise, A-weighted).
[C-1-7] MUST have a total harmonic distortion (THD) less than be less than 1% for 1 kHZ at 90 dB SPL input level at each and every microphone used to record the unprocessed audio source.
[C-1-8] MUST not have any other signal processing (eg Automatic Gain Control, High Pass Filter, or Echo cancellation) in the path other than a level multiplier to bring the level to desired range. Başka bir deyişle:
- [C-1-9] If any signal processing is present in the architecture for any reason, it MUST be disabled and effectively introduce zero delay or extra latency to the signal path.
- [C-1-10] The level multiplier, while allowed to be on the path, MUST NOT introduce delay or latency to the signal path.
All SPL measurements are made directly next to the microphone under test. For multiple microphone configurations, these requirements apply to each microphone.
If device implementations declare android.hardware.microphone
but do not support unprocessed audio source, they:
- [C-2-1] MUST return
null
for theAudioManager.getProperty(PROPERTY_SUPPORT_AUDIO_SOURCE_UNPROCESSED)
API method, to properly indicate the lack of support. - [C-SR-1] are still STRONGLY RECOMMENDED to satisfy as many of the requirements for the signal path for the unprocessed recording source.
6. Developer Tools and Options Compatibility
6.1. Developer Tools
Cihaz uygulamaları:
- [C-0-1] MUST support the Android Developer Tools provided in the Android SDK.
- [C-0-2] MUST support adb as documented in the Android SDK and the shell commands provided in the AOSP, which can be used by app developers, including
dumpsys
cmd stats
- [C-0-11] MUST support the shell command
cmd testharness
. Upgrading device implementations from an earlier Android version without a persistent data block MAY be exempted from C-0-11. - [C-0-3] MUST NOT alter the format or the contents of device system events (batterystats , diskstats, fingerprint, graphicsstats, netstats, notification, procstats) logged via the dumpsys command.
- [C-0-10] MUST record, without omission, and make the following events accessible and available to the
cmd stats
shell command and theStatsManager
System API class.- ActivityForegroundStateChanged
- AnomalyDetected
- AppBreadcrumbReported
- AppCrashOccurred
- AppStartOccurred
- BatteryLevelChanged
- BatterySaverModeStateChanged
- BleScanResultReceived
- BleScanStateChanged
- ChargingStateChanged
- DeviceIdleModeStateChanged
- ForegroundServiceStateChanged
- GpsScanStateChanged
- JobStateChanged
- PluggedStateChanged
- ScheduledJobStateChanged
- ScreenStateChanged
- SyncStateChanged
- SystemElapsedRealtime
- UidProcessStateChanged
- WakelockStateChanged
- WakeupAlarmOccurred
- WifiLockStateChanged
- WifiMulticastLockStateChanged
- WifiScanStateChanged
- [C-0-4] MUST have the device-side adb daemon be inactive by default and there MUST be a user-accessible mechanism to turn on the Android Debug Bridge.
- [C-0-5] MUST support secure adb. Android includes support for secure adb. Secure adb enables adb on known authenticated hosts.
- [C-0-6] MUST provide a mechanism allowing adb to be connected from a host machine. Özellikle:
If device implementations without a USB port support peripheral mode, they:
- [C-3-1] MUST implement adb via local-area network (such as Ethernet or Wi-Fi).
- [C-3-2] MUST provide drivers for Windows 7, 8 and 10, allowing developers to connect to the device using the adb protocol.
If device implementations support adb connections to a host machine via Wi-Fi, they:
- [C-4-1] MUST have the
AdbManager#isAdbWifiSupported()
method returntrue
.
If device implementations support adb connections to a host machine via Wi-Fi and includes at least one camera, they:
- [C-5-1] MUST have the
AdbManager#isAdbWifiQrSupported()
method returntrue
.
- [C-0-2] MUST support adb as documented in the Android SDK and the shell commands provided in the AOSP, which can be used by app developers, including
Dalvik Debug Monitor Service (ddms)
- [C-0-7] MUST support all ddms features as documented in the Android SDK. As ddms uses adb, support for ddms SHOULD be inactive by default, but MUST be supported whenever the user has activated the Android Debug Bridge, as above.
- [C-0-8] MUST include the Monkey framework and make it available for applications to use.
- [C-0-9] MUST support the systrace tool as documented in the Android SDK. Systrace must be inactive by default and there MUST be a user-accessible mechanism to turn on Systrace.
- [C-SR-1] Are STRONGLY RECOMMENDED to expose a
/system/bin/perfetto
binary to the shell user which cmdline complies with the perfetto documentation . - [C-SR-2] The perfetto binary is STRONGLY RECOMMENDED to accept as input a protobuf config that complies with the schema defined in the perfetto documentation .
- [C-SR-3] The perfetto binary is STRONGLY RECOMMENDED to write as output a protobuf trace that complies with the schema defined in the perfetto documentation .
- [C-SR-4] Are STRONGLY RECOMMENDED to provide, through the perfetto binary, at least the data sources described in the perfetto documentation .
- [C-SR-1] Are STRONGLY RECOMMENDED to expose a
- [C-0-10] MUST write a
LMK_KILL_OCCURRED_FIELD_NUMBER
Atom to the statsd log when an app is terminated by the Low Memory Killer .
- [C-0-10] MUST write a
Test Harness Mode If device implementations support the shell command
cmd testharness
and runcmd testharness enable
, they:- [C-2-1] MUST return
true
forActivityManager.isRunningInUserTestHarness()
- [C-2-2] MUST implement Test Harness Mode as described in Test Harness Mode documentation .
- [C-2-1] MUST return
If device implementations report the support of Vulkan 1.0 or higher via the android.hardware.vulkan.version
feature flags, they:
- [C-1-1] MUST provide an affordance for the app developer to enable/disable GPU debug layers.
- [C-1-2] MUST, when the GPU debug layers are enabled, enumerate layers in libraries provided by external tools (ie not part of the platform or application package) found in debuggable applications' base directory to support vkEnumerateInstanceLayerProperties() and vkCreateInstance() API methods.
6.2. Geliştirici Seçenekleri
Android includes support for developers to configure application development-related settings.
Device implementations MUST provide a consistent experience for Developer Options, they:
- [C-0-1] MUST honor the android.settings.APPLICATION_DEVELOPMENT_SETTINGS intent to show application development-related settings. The upstream Android implementation hides the Developer Options menu by default and enables users to launch Developer Options after pressing seven (7) times on the Settings > About Device > Build Number menu item.
- [C-0-2] MUST hide Developer Options by default.
- [C-0-3] MUST provide a clear mechanism that does not give preferential treatment to one third-party app as opposed to another to enable Developer Options. MUST provide a public visible document or website that describes how to enable Developer Options. This document or website MUST be linkable from the Android SDK documents.
- SHOULD have an ongoing visual notification to the user when Developer Options is enabled and the safety of the user is of concern.
- MAY temporarily limit access to the Developer Options menu, by visually hiding or disabling the menu, to prevent distraction for scenarios where the safety of the user is of concern.
7. Hardware Compatibility
If a device includes a particular hardware component that has a corresponding API for third-party developers:
- [C-0-1] The device implementation MUST implement that API as described in the Android SDK documentation.
If an API in the SDK interacts with a hardware component that is stated to be optional and the device implementation does not possess that component:
- [C-0-2] Complete class definitions (as documented by the SDK) for the component APIs MUST still be presented.
- [C-0-3] The API's behaviors MUST be implemented as no-ops in some reasonable fashion.
- [C-0-4] API methods MUST return null values where permitted by the SDK documentation.
- [C-0-5] API methods MUST return no-op implementations of classes where null values are not permitted by the SDK documentation.
- [C-0-6] API methods MUST NOT throw exceptions not documented by the SDK documentation.
- [C-0-7] Device implementations MUST consistently report accurate hardware configuration information via the
getSystemAvailableFeatures()
andhasSystemFeature(String)
methods on the android.content.pm.PackageManager class for the same build fingerprint.
A typical example of a scenario where these requirements apply is the telephony API: Even on non-phone devices, these APIs must be implemented as reasonable no-ops.
7.1. Display and Graphics
Android includes facilities that automatically adjust application assets and UI layouts appropriately for the device to ensure that third-party applications run well on a variety of hardware configurations . On the Android-compatible display(s) where all third-party Android-compatible applications can run, device implementations MUST properly implement these APIs and behaviors, as detailed in this section.
The units referenced by the requirements in this section are defined as follows:
- physical diagonal size . The distance in inches between two opposing corners of the illuminated portion of the display.
- dots per inch (dpi) . The number of pixels encompassed by a linear horizontal or vertical span of 1”. Where dpi values are listed, both horizontal and vertical dpi must fall within the range.
- aspect ratio . The ratio of the pixels of the longer dimension to the shorter dimension of the screen. For example, a display of 480x854 pixels would be 854/480 = 1.779, or roughly “16:9”.
- density-independent pixel (dp) . The virtual pixel unit normalized to a 160 dpi screen, calculated as: pixels = dps * (density/160).
7.1.1. Screen Configuration
7.1.1.1. Screen Size and Shape
The Android UI framework supports a variety of different logical screen layout sizes, and allows applications to query the current configuration's screen layout size via Configuration.screenLayout
with the SCREENLAYOUT_SIZE_MASK
and Configuration.smallestScreenWidthDp
.
Cihaz uygulamaları:
[C-0-1] MUST report the correct layout size for the
Configuration.screenLayout
as defined in the Android SDK documentation. Specifically, device implementations MUST report the correct logical density-independent pixel (dp) screen dimensions as below:- Devices with the
Configuration.uiMode
set as any value other than UI_MODE_TYPE_WATCH, and reporting asmall
size for theConfiguration.screenLayout
, MUST have at least 426 dp x 320 dp. - Devices reporting a
normal
size for theConfiguration.screenLayout
, MUST have at least 480 dp x 320 dp. - Devices reporting a
large
size for theConfiguration.screenLayout
, MUST have at least 640 dp x 480 dp. - Devices reporting a
xlarge
size for theConfiguration.screenLayout
, MUST have at least 960 dp x 720 dp.
- Devices with the
[C-0-2] MUST correctly honor applications' stated support for screen sizes through the <
supports-screens
> attribute in the AndroidManifest.xml, as described in the Android SDK documentation.MAY have the Android-compatible display(s) with rounded corners.
If device implementations support UI_MODE_TYPE_NORMAL
and include Android-compatible display(s) with rounded corners, they:
[C-1-1] MUST ensure that at least one of the following requirements is met:
- The radius of the rounded corners is less than or equal to 38 dp.
- When a 15 dp by 15 dp box is anchored at each corner of the logical display, at least one pixel of each box is visible on the screen.
SHOULD include user affordance to switch to the display mode with the rectangular corners.
If device implementations include an Android-compatible display(s) that is foldable, or includes a folding hinge between multiple display panels and makes such display(s) available to render third-party apps, they:
- [C-2-1] MUST implement the latest available stable version of the extensions API or the stable version of sidecar API to be used by Window Manager Jetpack library.
If device implementations include an Android-compatible display(s) that is foldable, or includes a folding hinge between multiple display panels and if the hinge or fold crosses a fullscreen application window, they:
- [C-3-1] MUST report the position, bounds and state of hinge or fold through extensions or sidecar APIs to the application.
For details on correctly implementing the sidecar or extension APIs refer to the public documentation of Window Manager Jetpack .
7.1.1.2. Screen Aspect Ratio
While there is no restriction to the aspect ratio of the physical display for the Android-compatible display(s), the aspect ratio of the logical display where third-party apps are rendered, which can be derived from the height and width values reported through the view.Display
APIs and Configuration APIs, MUST meet the following requirements:
[C-0-1] Device implementations with
Configuration.uiMode
set toUI_MODE_TYPE_NORMAL
MUST have an aspect ratio value less than or equal to 1.86 (roughly 16:9), unless the app meets one of the following conditions:- The app has declared that it supports a larger screen aspect ratio through the
android.max_aspect
metadata value. - The app declares it is resizeable via the android:resizeableActivity attribute.
- The app targets API level 24 or higher and does not declare an
android:maxAspectRatio
that would restrict the allowed aspect ratio.
- The app has declared that it supports a larger screen aspect ratio through the
[C-0-3] Device implementations with the
Configuration.uiMode
set asUI_MODE_TYPE_WATCH
MUST have an aspect ratio value set as 1.0 (1:1).
7.1.1.3. Ekran Yoğunluğu
The Android UI framework defines a set of standard logical densities to help application developers target application resources.
[C-0-1] By default, device implementations MUST report only one of the Android framework densities that are listed on
DisplayMetrics
through theDENSITY_DEVICE_STABLE
API and this value MUST NOT change at any time; however, the device MAY report a different arbitrary density according to the display configuration changes made by the user (for example, display size) set after initial boot.Device implementations SHOULD define the standard Android framework density that is numerically closest to the physical density of the screen, unless that logical density pushes the reported screen size below the minimum supported. If the standard Android framework density that is numerically closest to the physical density results in a screen size that is smaller than the smallest supported compatible screen size (320 dp width), device implementations SHOULD report the next lowest standard Android framework density.
If there is an affordance to change the display size of the device:
- [C-1-1] The display size MUST NOT be scaled any larger than 1.5 times the native density or produce an effective minimum screen dimension smaller than 320dp (equivalent to resource qualifier sw320dp), whichever comes first.
- [C-1-2] Display size MUST NOT be scaled any smaller than 0.85 times the native density.
- To ensure good usability and consistent font sizes, it is RECOMMENDED that the following scaling of Native Display options be provided (while complying with the limits specified above)
- Small: 0.85x
- Default: 1x (Native display scale)
- Large: 1.15x
- Larger: 1.3x
- Largest 1.45x
7.1.2. Display Metrics
If device implementations include the Android-compatible display(s) or video output to the Android-compatible display screen(s), they:
- [C-1-1] MUST report correct values for all Android-compatible display metrics defined in the
android.util.DisplayMetrics
API.
If device implementations does not include an embedded screen or video output, they:
- [C-2-1] MUST report correct values of the Android-compatible display as defined in the
android.util.DisplayMetrics
API for the emulated defaultview.Display
.
7.1.3. Screen Orientation
Cihaz uygulamaları:
- [C-0-1] MUST report which screen orientations they support (
android.hardware.screen.portrait
and/orandroid.hardware.screen.landscape
) and MUST report at least one supported orientation. For example, a device with a fixed orientation landscape screen, such as a television or laptop, SHOULD only reportandroid.hardware.screen.landscape
. - [C-0-2] MUST report the correct value for the device's current orientation, whenever queried via the
android.content.res.Configuration.orientation
,android.view.Display.getOrientation()
, or other APIs.
If device implementations support both screen orientations, they:
- [C-1-1] MUST support dynamic orientation by applications to either portrait or landscape screen orientation. That is, the device must respect the application's request for a specific screen orientation.
- [C-1-2] MUST NOT change the reported screen size or density when changing orientation.
- MAY select either portrait or landscape orientation as the default.
7.1.4. 2D and 3D Graphics Acceleration
7.1.4.1 OpenGL ES
Cihaz uygulamaları:
- [C-0-1] MUST correctly identify the supported OpenGL ES versions (1.1, 2.0, 3.0, 3.1, 3.2) through the managed APIs (such as via the
GLES10.getString()
method) and the native APIs. - [C-0-2] MUST include the support for all the corresponding managed APIs and native APIs for every OpenGL ES versions they identified to support.
If device implementations include a screen or video output, they:
- [C-1-1] MUST support both OpenGL ES 1.1 and 2.0, as embodied and detailed in the Android SDK documentation .
- [C-SR-1] Are STRONGLY RECOMMENDED to support OpenGL ES 3.1.
- SHOULD support OpenGL ES 3.2.
The OpenGL ES dEQP tests are partitioned into a number of test lists, each with an associated date/version number. These are in the Android source tree at external/deqp/android/cts/main/glesXX-master-YYYY-MM-DD.txt
. A device that supports OpenGL ES at a self-reported level indicates that it can pass the dEQP tests in all test lists from this level and earlier.
If device implementations support any of the OpenGL ES versions, they:
- [C-2-1] MUST report via the OpenGL ES managed APIs and native APIs any other OpenGL ES extensions they have implemented, and conversely MUST NOT report extension strings that they do not support.
- [C-2-2] MUST support the
EGL_KHR_image
,EGL_KHR_image_base
,EGL_ANDROID_image_native_buffer
,EGL_ANDROID_get_native_client_buffer
,EGL_KHR_wait_sync
,EGL_KHR_get_all_proc_addresses
,EGL_ANDROID_presentation_time
,EGL_KHR_swap_buffers_with_damage
,EGL_ANDROID_recordable
, andEGL_ANDROID_GLES_layers
extensions. - [C-2-3] MUST report the maximum version of the OpenGL ES dEQP tests supported via the
android.software.opengles.deqp.level
feature flag. - [C-2-4] MUST at least support version 132383489 (from Mar 1st, 2020) as reported in the
android.software.opengles.deqp.level
feature flag. - [C-2-5] MUST pass all OpenGL ES dEQP Tests in the test lists between version 132383489 and the version specified in the
android.software.opengles.deqp.level
feature flag, for each supported OpenGL ES version. - [C-SR-2] Are STRONGLY RECOMMENDED to support the
EGL_KHR_partial_update
andOES_EGL_image_external
extensions. - SHOULD accurately report via the
getString()
method, any texture compression format that they support, which is typically vendor-specific.
If device implementations declare support for OpenGL ES 3.0, 3.1, or 3.2, they:
- [C-3-1] MUST export the corresponding function symbols for these version in addition to the OpenGL ES 2.0 function symbols in the libGLESv2.so library.
- [C-SR-3] Are STRONGLY RECOMMENDED to support the
OES_EGL_image_external_essl3
extension.
If device implementations support OpenGL ES 3.2, they:
- [C-4-1] MUST support the OpenGL ES Android Extension Pack in its entirety.
If device implementations support the OpenGL ES Android Extension Pack in its entirety, they:
- [C-5-1] MUST identify the support through the
android.hardware.opengles.aep
feature flag.
If device implementations expose support for the EGL_KHR_mutable_render_buffer
extension, they:
- [C-6-1] MUST also support the
EGL_ANDROID_front_buffer_auto_refresh
extension.
7.1.4.2 Vulkan
Android includes support for Vulkan , a low-overhead, cross-platform API for high-performance 3D graphics.
If device implementations support OpenGL ES 3.1, they:
- [C-SR-1] Are STRONGLY RECOMMENDED to include support for Vulkan 1.1.
If device implementations include a screen or video output, they:
- SHOULD include support for Vulkan 1.1.
The Vulkan dEQP tests are partitioned into a number of test lists, each with an associated date/version. These are in the Android source tree at external/deqp/android/cts/main/vk-master-YYYY-MM-DD.txt
. A device that supports Vulkan at a self-reported level indicates that it can pass the dEQP tests in all test lists from this level and earlier.
If device implementations include support for Vulkan 1.0 or higher, they:
- [C-1-1] MUST report the correct integer value with the
android.hardware.vulkan.level
andandroid.hardware.vulkan.version
feature flags. - [C-1-2] MUST enumerate, at least one
VkPhysicalDevice
for the Vulkan native APIvkEnumeratePhysicalDevices()
. - [C-1-3] MUST fully implement the Vulkan 1.0 APIs for each enumerated
VkPhysicalDevice
. - [C-1-4] MUST enumerate layers, contained in native libraries named as
libVkLayer*.so
in the application package's native library directory, through the Vulkan native APIsvkEnumerateInstanceLayerProperties()
andvkEnumerateDeviceLayerProperties()
. - [C-1-5] MUST NOT enumerate layers provided by libraries outside of the application package, or provide other ways of tracing or intercepting the Vulkan API, unless the application has the
android:debuggable
attribute set astrue
. - [C-1-6] MUST report all extension strings that they do support via the Vulkan native APIs , and conversely MUST NOT report extension strings that they do not correctly support.
- [C-1-7] MUST support the VK_KHR_surface, VK_KHR_android_surface, VK_KHR_swapchain, and VK_KHR_incremental_present extensions.
- [C-1-8] MUST report the maximum version of the Vulkan dEQP Tests supported via the
android.software.vulkan.deqp.level
feature flag. - [C-1-9] MUST at least support version
132317953
(from Mar 1st, 2019) as reported in theandroid.software.vulkan.deqp.level
feature flag. - [C-1-10] MUST pass all Vulkan dEQP Tests in the test lists between version
132317953
and the version specified in theandroid.software.vulkan.deqp.level
feature flag. - [C-1-11] MUST NOT enumerate support for the VK_KHR_video_queue, VK_KHR_video_decode_queue, or VK_KHR_video_encode_queue extensions.
- [C-SR-2] Are STRONGLY RECOMMENDED to support the VK_KHR_driver_properties and VK_GOOGLE_display_timing extensions.
If device implementations do not include support for Vulkan 1.0, they:
- [C-2-1] MUST NOT declare any of the Vulkan feature flags (eg
android.hardware.vulkan.level
,android.hardware.vulkan.version
). - [C-2-2] MUST NOT enumerate any
VkPhysicalDevice
for the Vulkan native APIvkEnumeratePhysicalDevices()
.
If device implementations include support for Vulkan 1.1 and declare any of the Vulkan feature flags, they:
- [C-3-1] MUST expose support for the
SYNC_FD
external semaphore and handle types and theVK_ANDROID_external_memory_android_hardware_buffer
extension.
7.1.4.3 RenderScript
- [C-0-1] Device implementations MUST support Android RenderScript , as detailed in the Android SDK documentation.
7.1.4.4 2D Graphics Acceleration
Android includes a mechanism for applications to declare that they want to enable hardware acceleration for 2D graphics at the Application, Activity, Window, or View level through the use of a manifest tag android:hardwareAccelerated or direct API calls.
Cihaz uygulamaları:
- [C-0-1] MUST enable hardware acceleration by default, and MUST disable hardware acceleration if the developer so requests by setting android:hardwareAccelerated="false” or disabling hardware acceleration directly through the Android View APIs.
- [C-0-2] MUST exhibit behavior consistent with the Android SDK documentation on hardware acceleration .
Android includes a TextureView object that lets developers directly integrate hardware-accelerated OpenGL ES textures as rendering targets in a UI hierarchy.
Cihaz uygulamaları:
- [C-0-3] MUST support the TextureView API, and MUST exhibit consistent behavior with the upstream Android implementation.
7.1.4.5 Wide-gamut Displays
If device implementations claim support for wide-gamut displays through Configuration.isScreenWideColorGamut()
, they:
- [C-1-1] MUST have a color-calibrated display.
- [C-1-2] MUST have a display whose gamut covers the sRGB color gamut entirely in CIE 1931 xyY space.
- [C-1-3] MUST have a display whose gamut has an area of at least 90% of DCI-P3 in CIE 1931 xyY space.
- [C-1-4] MUST support OpenGL ES 3.1 or 3.2 and report it properly.
- [C-1-5] MUST advertise support for the
EGL_KHR_no_config_context
,EGL_EXT_pixel_format_float
,EGL_KHR_gl_colorspace
,EGL_EXT_gl_colorspace_scrgb
,EGL_EXT_gl_colorspace_scrgb_linear
,EGL_EXT_gl_colorspace_display_p3
,EGL_EXT_gl_colorspace_display_p3_linear
, andEGL_EXT_gl_colorspace_display_p3_passthrough
extensions. - [C-SR-1] Are STRONGLY RECOMMENDED to support
GL_EXT_sRGB
.
Conversely, if device implementations do not support wide-gamut displays, they:
- [C-2-1] SHOULD cover 100% or more of sRGB in CIE 1931 xyY space, although the screen color gamut is undefined.
7.1.5. Legacy Application Compatibility Mode
Android specifies a “compatibility mode” in which the framework operates in a 'normal' screen size equivalent (320dp width) mode for the benefit of legacy applications not developed for old versions of Android that pre-date screen-size independence.
7.1.6. Ekran Teknolojisi
The Android platform includes APIs that allow applications to render rich graphics to an Android-compatible display. Devices MUST support all of these APIs as defined by the Android SDK unless specifically allowed in this document.
All of a device implementation's Android-compatible displays:
- [C-0-1] MUST be capable of rendering 16-bit color graphics.
- SHOULD support displays capable of 24-bit color graphics.
- [C-0-2] MUST be capable of rendering animations.
- [C-0-3] MUST have a pixel aspect ratio (PAR) between 0.9 and 1.15. That is, the pixel aspect ratio MUST be near square (1.0) with a 10 ~ 15% tolerance.
7.1.7. Secondary Displays
Android includes support for secondary Android-compatible displays to enable media sharing capabilities and developer APIs for accessing external displays.
If device implementations support an external display either via a wired, wireless, or an embedded additional display connection, they:
- [C-1-1] MUST implement the
DisplayManager
system service and API as described in the Android SDK documentation.
7.2. Giriş cihazları
Cihaz uygulamaları:
- [C-0-1] MUST include an input mechanism, such as a touchscreen or non-touch navigation , to navigate between the UI elements.
7.2.1. Tuş takımı
If device implementations include support for third-party Input Method Editor (IME) applications, they:
- [C-1-1] MUST declare the
android.software.input_methods
feature flag. - [C-1-2] MUST implement fully
Input Management Framework
- [C-1-3] MUST have a preinstalled software keyboard.
Cihaz uygulamaları:
- [C-0-1] MUST NOT include a hardware keyboard that does not match one of the formats specified in android.content.res.Configuration.keyboard (QWERTY or 12-key).
- SHOULD include additional soft keyboard implementations.
- MAY include a hardware keyboard.
7.2.2. Non-touch Navigation
Android includes support for d-pad, trackball, and wheel as mechanisms for non-touch navigation.
Cihaz uygulamaları:
- [C-0-1] MUST report the correct value for android.content.res.Configuration.navigation .
If device implementations lack non-touch navigations, they:
- [C-1-1] MUST provide a reasonable alternative user interface mechanism for the selection and editing of text, compatible with Input Management Engines. The upstream Android open source implementation includes a selection mechanism suitable for use with devices that lack non-touch navigation inputs.
7.2.3. Navigation Keys
The Home , Recents , and Back functions typically provided via an interaction with a dedicated physical button or a distinct portion of the touch screen, are essential to the Android navigation paradigm and therefore, device implementations:
- [C-0-1] MUST provide a user affordance to launch installed applications that have an activity with the
<intent-filter>
set withACTION=MAIN
andCATEGORY=LAUNCHER
orCATEGORY=LEANBACK_LAUNCHER
for Television device implementations. The Home function SHOULD be the mechanism for this user affordance. - SHOULD provide buttons for the Recents and Back function.
If the Home, Recents, or Back functions are provided, they:
- [C-1-1] MUST be accessible with a single action (eg tap, double-click or gesture) when any of them are accessible.
- [C-1-2] MUST provide a clear indication of which single action would trigger each function. Having a visible icon imprinted on the button, showing a software icon on the navigation bar portion of the screen, or walking the user through a guided step-by-step demo flow during the out-of-box setup experience are examples of such an indication.
Cihaz uygulamaları:
- [C-SR-1] are STRONGLY RECOMMENDED to not provide the input mechanism for the Menu function as it is deprecated in favor of action bar since Android 4.0.
If device implementations provide the Menu function, they:
- [C-2-1] MUST display the action overflow button whenever the action overflow menu popup is not empty and the action bar is visible.
- [C-2-2] MUST NOT modify the position of the action overflow popup displayed by selecting the overflow button in the action bar, but MAY render the action overflow popup at a modified position on the screen when it is displayed by selecting the Menu işlev.
If device implementations do not provide the Menu function, for backwards compatibility, they:
- [C-3-1] MUST make the Menu function available to applications when
targetSdkVersion
is less than 10, either by a physical button, a software key, or gestures. This Menu function should be accessible unless hidden together with other navigation functions.
If device implementations provide the Assist function , they:
- [C-4-1] MUST make the Assist function accessible with a single action (eg tap, double-click or gesture) when other navigation keys are accessible.
- [C-SR-2] STRONGLY RECOMMENDED to use long press on HOME function as this designated interaction.
If device implementations use a distinct portion of the screen to display the navigation keys, they:
- [C-5-1] Navigation keys MUST use a distinct portion of the screen, not available to applications, and MUST NOT obscure or otherwise interfere with the portion of the screen available to applications.
- [C-5-2] MUST make available a portion of the display to applications that meets the requirements defined in section 7.1.1 .
- [C-5-3] MUST honor the flags set by the app through the
View.setSystemUiVisibility()
API method, so that this distinct portion of the screen (aka the navigation bar) is properly hidden away as documented in the SDK.
Gezinme işlevi ekranda, harekete dayalı bir eylem olarak sağlanıyorsa:
- [C-6-1]
WindowInsets#getMandatorySystemGestureInsets()
MUST only be used to report the Home gesture recognition area. - [C-6-2] Gestures that start within an exclusion rect as provided by the foreground application via
View#setSystemGestureExclusionRects()
, but outside ofWindowInsets#getMandatorySystemGestureInsets()
, MUST NOT be intercepted for the navigation function as long as the exclusion rect is allowed within the max exclusion limit as specified in the documentation forView#setSystemGestureExclusionRects()
. - [C-6-3] MUST send the foreground app a
MotionEvent.ACTION_CANCEL
event once touches start being intercepted for a system gesture, if the foreground app was previously sent anMotionEvent.ACTION_DOWN
event. - [C-6-4] MUST provide a user affordance to switch to an on-screen, button-based navigation (for example, in Settings).
- SHOULD provide Home function as a swipe up from the bottom edge of the current orientation of the screen.
- SHOULD provide Recents function as a swipe up and hold before release, from the same area as the Home gesture.
- Gestures that start within
WindowInsets#getMandatorySystemGestureInsets()
SHOULD NOT be affected by exclusion rects provided by the foreground application viaView#setSystemGestureExclusionRects()
.
If a navigation function is provided from anywhere on the left and right edges of the current orientation of the screen:
- [C-7-1] The navigation function MUST be Back and provided as a swipe from both left and right edges of the current orientation of the screen.
- [C-7-2] If custom swipeable system panels are provided on the left or right edges, they MUST be placed within the top 1/3rd of the screen with a clear, persistent visual indication that dragging in would invoke the aforementioned panels, and hence not Back. A system panel MAY be configured by a user such that it lands below the top 1/3rd of the screen edge(s) but the system panel MUST NOT use longer than 1/3rd of the edge(s).
- [C-7-3] When the foreground app has either the View.SYSTEM_UI_FLAG_IMMERSIVE, View.SYSTEM_UI_FLAG_IMMERSIVE_STICKY, WindowInsetsController.BEHAVIOR_DEFAULT, or WindowInsetsController.BEHAVIOR_SHOW_TRANSIENT_BARS_BY_SWIPE flags set, swiping from the edges MUST behave as implemented in AOSP, which is documented in the SDK .
- [C-7-4] When the foreground app has either the View.SYSTEM_UI_FLAG_IMMERSIVE, View.SYSTEM_UI_FLAG_IMMERSIVE_STICKY, WindowInsetsController.BEHAVIOR_DEFAULT, or WindowInsetsController.BEHAVIOR_SHOW_TRANSIENT_BARS_BY_SWIPE flags set, custom swipeable system panels MUST be hidden until the user brings in or un-dims the system bars (aka navigation and status bar) as implemented in AOSP.
7.2.4. Touchscreen Input
Android includes support for a variety of pointer input systems, such as touchscreens, touch pads, and fake touch input devices. Touchscreen-based device implementations are associated with a display such that the user has the impression of directly manipulating items on screen. Since the user is directly touching the screen, the system does not require any additional affordances to indicate the objects being manipulated.
Cihaz uygulamaları:
- SHOULD have a pointer input system of some kind (either mouse-like or touch).
- SHOULD support fully independently tracked pointers.
If device implementations include a touchscreen (single-touch or better) on a primary Android-compatible display, they:
- [C-1-1] MUST report
TOUCHSCREEN_FINGER
for theConfiguration.touchscreen
API field. - [C-1-2] MUST report the
android.hardware.touchscreen
andandroid.hardware.faketouch
feature flags.
If device implementations include a touchscreen that can track more than a single touch on a primary Android-compatible display, they:
- [C-2-1] MUST report the appropriate feature flags
android.hardware.touchscreen.multitouch
,android.hardware.touchscreen.multitouch.distinct
,android.hardware.touchscreen.multitouch.jazzhand
corresponding to the type of the specific touchscreen on the cihaz.
If device implementations rely on an external input device such as mouse or trackball (ie not directly touching the screen) for input on a primary Android-compatible display and meet the fake touch requirements in section 7.2.5 , they:
- [C-3-1] MUST NOT report any feature flag starting with
android.hardware.touchscreen
. - [C-3-2] MUST report only
android.hardware.faketouch
. - [C-3-3] MUST report
TOUCHSCREEN_NOTOUCH
for theConfiguration.touchscreen
API field.
7.2.5. Fake Touch Input
Fake touch interface provides a user input system that approximates a subset of touchscreen capabilities. For example, a mouse or remote control that drives an on-screen cursor approximates touch, but requires the user to first point or focus then click. Numerous input devices like the mouse, trackpad, gyro-based air mouse, gyro-pointer, joystick, and multi-touch trackpad can support fake touch interactions. Android includes the feature constant android.hardware.faketouch, which corresponds to a high-fidelity non-touch (pointer-based) input device such as a mouse or trackpad that can adequately emulate touch-based input (including basic gesture support), and indicates that the device supports an emulated subset of touchscreen functionality.
If device implementations do not include a touchscreen but include another pointer input system which they want to make available, they:
- SHOULD declare support for the
android.hardware.faketouch
feature flag.
If device implementations declare support for android.hardware.faketouch
, they:
- [C-1-1] MUST report the absolute X and Y screen positions of the pointer location and display a visual pointer on the screen.
- [C-1-2] MUST report touch event with the action code that specifies the state change that occurs on the pointer going down or up on the screen .
- [C-1-3] MUST support pointer down and up on an object on the screen, which allows users to emulate tap on an object on the screen.
- [C-1-4] MUST support pointer down, pointer up, pointer down then pointer up in the same place on an object on the screen within a time threshold, which allows users to emulate double tap on an object on the screen.
- [C-1-5] MUST support pointer down on an arbitrary point on the screen, pointer move to any other arbitrary point on the screen, followed by a pointer up, which allows users to emulate a touch drag.
- [C-1-6] MUST support pointer down then allow users to quickly move the object to a different position on the screen and then pointer up on the screen, which allows users to fling an object on the screen.
If device implementations declare support for android.hardware.faketouch.multitouch.distinct
, they:
- [C-2-1] MUST declare support for
android.hardware.faketouch
. - [C-2-2] MUST support distinct tracking of two or more independent pointer inputs.
If device implementations declare support for android.hardware.faketouch.multitouch.jazzhand
, they:
- [C-3-1] MUST declare support for
android.hardware.faketouch
. - [C-3-2] MUST support distinct tracking of 5 (tracking a hand of fingers) or more pointer inputs fully independently.
7.2.6. Game Controller Support
7.2.6.1. Button Mappings
Cihaz uygulamaları:
- [C-1-1] MUST be capable to map HID events to the corresponding
InputEvent
constants as listed in the below tables. The upstream Android implementation satisfies this requirement.
If device implementations embed a controller or ship with a separate controller in the box that would provide means to input all the events listed in the below tables, they:
- [C-2-1] MUST declare the feature flag
android.hardware.gamepad
Düğme | HID Usage 2 | Android Button |
---|---|---|
1 _ | 0x09 0x0001 | KEYCODE_BUTTON_A (96) |
B1 _ | 0x09 0x0002 | KEYCODE_BUTTON_B (97) |
X 1 | 0x09 0x0004 | KEYCODE_BUTTON_X (99) |
Y 1 | 0x09 0x0005 | KEYCODE_BUTTON_Y (100) |
D-pad up 1 D-pad down 1 | 0x01 0x0039 3 | AXIS_HAT_Y 4 |
D-pad left 1 D-pad right 1 | 0x01 0x0039 3 | AXIS_HAT_X 4 |
Left shoulder button 1 | 0x09 0x0007 | KEYCODE_BUTTON_L1 (102) |
Right shoulder button 1 | 0x09 0x0008 | KEYCODE_BUTTON_R1 (103) |
Left stick click 1 | 0x09 0x000E | KEYCODE_BUTTON_THUMBL (106) |
Right stick click 1 | 0x09 0x000F | KEYCODE_BUTTON_THUMBR (107) |
Back 1 | 0x0c 0x0224 | KEYCODE_BACK (4) |
1 KeyEvent
2 The above HID usages must be declared within a Game pad CA (0x01 0x0005).
3 This usage must have a Logical Minimum of 0, a Logical Maximum of 7, a Physical Minimum of 0, a Physical Maximum of 315, Units in Degrees, and a Report Size of 4. The logical value is defined to be the clockwise rotation away from the vertical axis; for example, a logical value of 0 represents no rotation and the up button being pressed, while a logical value of 1 represents a rotation of 45 degrees and both the up and left keys being pressed.
Analog Controls 1 | HID Usage | Android Button |
---|---|---|
Left Trigger | 0x02 0x00C5 | AXIS_LTRIGGER |
Doğru tetik | 0x02 0x00C4 | AXIS_RTRIGGER |
Left Joystick | 0x01 0x0030 0x01 0x0031 | AXIS_X AXIS_Y |
Right Joystick | 0x01 0x0032 0x01 0x0035 | AXIS_Z AXIS_RZ |
7.2.7. Uzaktan kumanda
See Section 2.3.1 for device-specific requirements.
7.3. Sensörler
If device implementations include a particular sensor type that has a corresponding API for third-party developers, the device implementation MUST implement that API as described in the Android SDK documentation and the Android Open Source documentation on sensors .
Cihaz uygulamaları:
- [C-0-1] MUST accurately report the presence or absence of sensors per the
android.content.pm.PackageManager
class. - [C-0-2] MUST return an accurate list of supported sensors via the
SensorManager.getSensorList()
and similar methods. - [C-0-3] MUST behave reasonably for all other sensor APIs (for example, by returning
true
orfalse
as appropriate when applications attempt to register listeners, not calling sensor listeners when the corresponding sensors are not present; etc.).
If device implementations include a particular sensor type that has a corresponding API for third-party developers, they:
- [C-1-1] MUST report all sensor measurements using the relevant International System of Units (metric) values for each sensor type as defined in the Android SDK documentation.
- [C-1-2] MUST report sensor data with a maximum latency of 100 milliseconds + 2 * sample_time for the case of a sensor stream with a maximum requested latency of 0 ms when the application processor is active. This delay does not include any filtering delays.
- [C-1-3] MUST report the first sensor sample within 400 milliseconds + 2 * sample_time of the sensor being activated. It is acceptable for this sample to have an accuracy of 0.
- [C-1-4] For any API indicated by the Android SDK documentation to be a continuous sensor , device implementations MUST continuously provide periodic data samples that SHOULD have a jitter below 3%, where jitter is defined as the standard deviation of the difference of the reported timestamp values between consecutive events.
- [C-1-5] MUST ensure that the sensor event stream MUST NOT prevent the device CPU from entering a suspend state or waking up from a suspend state.
- [C-1-6] MUST report the event time in nanoseconds as defined in the Android SDK documentation, representing the time the event happened and synchronized with the SystemClock.elapsedRealtimeNano() clock.
- [C-SR-1] Are STRONGLY RECOMMENDED to have timestamp synchronization error below 100 milliseconds, and SHOULD have timestamp synchronization error below 1 millisecond.
- When several sensors are activated, the power consumption SHOULD NOT exceed the sum of the individual sensor's reported power consumption.
The list above is not comprehensive; the documented behavior of the Android SDK and the Android Open Source Documentations on sensors is to be considered authoritative.
If device implementations include a particular sensor type that has a corresponding API for third-party developers, they:
- [C-1-6] MUST set a non-zero resolution for all sensors, and report the value via the
Sensor.getResolution()
API method.
Some sensor types are composite, meaning they can be derived from data provided by one or more other sensors. (Examples include the orientation sensor and the linear acceleration sensor.)
Cihaz uygulamaları:
- SHOULD implement these sensor types, when they include the prerequisite physical sensors as described in sensor types .
If device implementations include a composite sensor, they:
- [C-2-1] MUST implement the sensor as described in the Android Open Source documentation on composite sensors .
If device implementations include a particular sensor type that has a corresponding API for third-party developers and the sensor only reports one value, then device implementations:
- [C-3-1] MUST set the resolution to 1 for the sensor and report the value via the
Sensor.getResolution()
API method.
If device implementations include a particular sensor type which supports SensorAdditionalInfo#TYPE_VEC3_CALIBRATION and the sensor is exposed to third-party developers, they:
- [C-4-1] MUST NOT include any fixed, factory-determined calibration parameters in the data provided.
If device implementations include a combination of 3-axis accelerometer, a 3-axis gyroscope sensor, or a magnetometer sensor, they are:
- [C-SR-2] STRONGLY RECOMMENDED to ensure the accelerometer, gyroscope and magnetometer have a fixed relative position, such that if the device is transformable (eg foldable), the sensor axes remain aligned and consistent with the sensor coordinate system throughout all possible device transformation states.
7.3.1. İvmeölçer
Cihaz uygulamaları:
- [C-SR-1] Are STRONGLY RECOMMENDED to include a 3-axis accelerometer.
Cihaz uygulamaları 3 eksenli bir ivmeölçer içeriyorsa:
- [C-1-1] MUST be able to report events up to a frequency of at least 50 Hz.
- [C-1-2] MUST implement and report
TYPE_ACCELEROMETER
sensor. - [C-1-3] MUST comply with the Android sensor coordinate system as detailed in the Android APIs.
- [C-1-4] MUST be capable of measuring from freefall up to four times the gravity(4g) or more on any axis.
- [C-1-5] MUST have a resolution of at least 12-bits.
- [C-1-6] MUST have a standard deviation no greater than 0.05 m/s^, where the standard deviation should be calculated on a per axis basis on samples collected over a period of at least 3 seconds at the fastest sampling rate.
- [C-SR-2] are STRONGLY RECOMMENDED to implement the
TYPE_SIGNIFICANT_MOTION
composite sensor. - [C-SR-3] are STRONGLY RECOMMENDED to implement and report
TYPE_ACCELEROMETER_UNCALIBRATED
sensor. Android devices are STRONGLY RECOMMENDED to meet this requirement so they will be able to upgrade to the future platform release where this might become REQUIRED. - SHOULD implement the
TYPE_SIGNIFICANT_MOTION
,TYPE_TILT_DETECTOR
,TYPE_STEP_DETECTOR
,TYPE_STEP_COUNTER
composite sensors as described in the Android SDK document. - SHOULD report events up to at least 200 Hz.
- SHOULD have a resolution of at least 16-bits.
- SHOULD be calibrated while in use if the characteristics changes over the life cycle and compensated, and preserve the compensation parameters between device reboots.
- SHOULD be temperature compensated.
If device implementations include a 3-axis accelerometer and any of the TYPE_SIGNIFICANT_MOTION
, TYPE_TILT_DETECTOR
, TYPE_STEP_DETECTOR
, TYPE_STEP_COUNTER
composite sensors are implemented:
- [C-2-1] The sum of their power consumption MUST always be less than 4 mW.
- SHOULD each be below 2 mW and 0.5 mW for when the device is in a dynamic or static condition.
If device implementations include a 3-axis accelerometer and a 3-axis gyroscope sensor, they:
- [C-3-1] MUST implement the
TYPE_GRAVITY
andTYPE_LINEAR_ACCELERATION
composite sensors. - [C-SR-4] Are STRONGLY RECOMMENDED to implement the
TYPE_GAME_ROTATION_VECTOR
composite sensor.
If device implementations include a 3-axis accelerometer, a 3-axis gyroscope sensor, and a magnetometer sensor, they:
- [C-4-1] MUST implement a
TYPE_ROTATION_VECTOR
composite sensor.
7.3.2. Manyetometre
Cihaz uygulamaları:
- [C-SR-1] Are STRONGLY RECOMMENDED to include a 3-axis magnetometer (compass).
If device implementations include a 3-axis magnetometer, they:
- [C-1-1] MUST implement the
TYPE_MAGNETIC_FIELD
sensor. - [C-1-2] MUST be able to report events up to a frequency of at least 10 Hz and SHOULD report events up to at least 50 Hz.
- [C-1-3] MUST comply with the Android sensor coordinate system as detailed in the Android APIs.
- [C-1-4] MUST be capable of measuring between -900 µT and +900 µT on each axis before saturating.
- [C-1-5] MUST have a hard iron offset value less than 700 µT and SHOULD have a value below 200 µT, by placing the magnetometer far from dynamic (current-induced) and static (magnet-induced) magnetic fields.
- [C-1-6] MUST have a resolution equal or denser than 0.6 µT.
- [C-1-7] MUST support online calibration and compensation of the hard iron bias, and preserve the compensation parameters between device reboots.
- [C-1-8] MUST have the soft iron compensation applied—the calibration can be done either while in use or during the production of the device.
- [C-1-9] MUST have a standard deviation, calculated on a per axis basis on samples collected over a period of at least 3 seconds at the fastest sampling rate, no greater than 1.5 µT; SHOULD have a standard deviation no greater than 0.5 µT.
- [C-1-10] MUST implement the
TYPE_MAGNETIC_FIELD_UNCALIBRATED
sensor.
If device implementations include a 3-axis magnetometer, an accelerometer sensor, and a 3-axis gyroscope sensor, they:
- [C-2-1] MUST implement a
TYPE_ROTATION_VECTOR
composite sensor.
If device implementations include a 3-axis magnetometer, an accelerometer, they:
- MAY implement the
TYPE_GEOMAGNETIC_ROTATION_VECTOR
sensor.
If device implementations include a 3-axis magnetometer, an accelerometer and TYPE_GEOMAGNETIC_ROTATION_VECTOR
sensor, they:
- [C-3-1] MUST consume less than 10 mW.
- SHOULD consume less than 3 mW when the sensor is registered for batch mode at 10 Hz.
7.3.3. Küresel Konumlama Sistemi
Cihaz uygulamaları:
- [C-SR-1] Are STRONGLY RECOMMENDED to include a GPS/GNSS receiver.
If device implementations include a GPS/GNSS receiver and report the capability to applications through the android.hardware.location.gps
feature flag, they:
- [C-1-1] MUST support location outputs at a rate of at least 1 Hz when requested via
LocationManager#requestLocationUpdate
. - [C-1-2] MUST be able to determine the location in open-sky conditions (strong signals, negligible multipath, HDOP < 2) within 10 seconds (fast time to first fix), when connected to a 0.5 Mbps or faster data speed internet connection. This requirement is typically met by the use of some form of Assisted or Predicted GPS/GNSS technique to minimize GPS/GNSS lock-on time (Assistance data includes Reference Time, Reference Location and Satellite Ephemeris/Clock).
- [C-1-6] After making such a location calculation, device implementations MUST determine its location, in open sky, within 5 seconds, when location requests are restarted, up to an hour after the initial location calculation, even when the subsequent request is made without a data connection, and/or after a power cycle.
In open sky conditions after determining the location, while stationary or moving with less than 1 meter per second squared of acceleration:
- [C-1-3] MUST be able to determine location within 20 meters, and speed within 0.5 meters per second, at least 95% of the time.
- [C-1-4] MUST simultaneously track and report via
GnssStatus.Callback
at least 8 satellites from one constellation. - SHOULD be able to simultaneously track at least 24 satellites, from multiple constellations (eg GPS + at least one of Glonass, Beidou, Galileo).
[C-SR-2] Are STRONGLY RECOMMENDED to continue to deliver normal GPS/GNSS location outputs through GNSS Location Provider API's during an emergency phone call.
[C-SR-3] Are STRONGLY RECOMMENDED to report GNSS measurements from all constellations tracked (as reported in GnssStatus messages), with the exception of SBAS.
[C-SR-4] Are STRONGLY RECOMMENDED to report AGC, and Frequency of GNSS measurement.
[C-SR-5] Are STRONGLY RECOMMENDED to report all accuracy estimates (including Bearing, Speed, and Vertical) as part of each GPS/GNSS location.
[C-SR-6] Are STRONGLY RECOMMENDED to report GNSS measurements, as soon as they are found, even if a location calculated from GPS/GNSS is not yet reported.
[C-SR-7] Are STRONGLY RECOMMENDED to report GNSS pseudoranges and pseudorange rates, that, in open-sky conditions after determining the location, while stationary or moving with less than 0.2 meter per second squared of acceleration, are sufficient to calculate position within 20 meters, and speed within 0.2 meters per second, at least 95% of the time.
7.3.4. Jiroskop
Cihaz uygulamaları:
- [C-SR-1] Are STRONGLY RECOMMENDED to include a gyroscope sensor.
If device implementations include a 3-axis gyroscope, they:
- [C-1-1] MUST be able to report events up to a frequency of at least 50 Hz.
- [C-1-2] MUST implement the
TYPE_GYROSCOPE
sensor. - [C-1-4] MUST have a resolution of 12-bits or more.
- [C-1-5] MUST be temperature compensated.
- [C-1-6] MUST be calibrated and compensated while in use, and preserve the compensation parameters between device reboots.
- [C-1-7] MUST have a variance no greater than 1e-7 rad^2 / s^2 per Hz (variance per Hz, or rad^2 / s). The variance is allowed to vary with the sampling rate, but MUST be constrained by this value. In other words, if you measure the variance of the gyro at 1 Hz sampling rate it SHOULD be no greater than 1e-7 rad^2/s^2.
- [C-SR-2] Calibration error is STRONGLY RECOMMENDED to be less than 0.01 rad/s when device is stationary at room temperature.
- [C-SR-3] Are STRONGLY RECOMMENDED to implement
TYPE_GYROSCOPE_UNCALIBRATED
sensor. - [C-SR-4] Are STRONGLY RECOMMENDED to have a resolution of 16-bits or more.
- SHOULD report events up to at least 200 Hz.
If device implementations include a 3-axis gyroscope, an accelerometer sensor and a magnetometer sensor, they:
- [C-2-1] MUST implement a
TYPE_ROTATION_VECTOR
composite sensor.
If device implementations include a 3-axis accelerometer and a 3-axis gyroscope sensor, they:
- [C-3-1] MUST implement the
TYPE_GRAVITY
andTYPE_LINEAR_ACCELERATION
composite sensors. - [C-SR-5] Are STRONGLY RECOMMENDED to implement the
TYPE_GAME_ROTATION_VECTOR
composite sensor.
7.3.5. Barometre
Cihaz uygulamaları:
- [C-SR-1] Are STRONGLY RECOMMENDED to include a barometer (ambient air pressure sensor).
If device implementations include a barometer, they:
- [C-1-1] MUST implement and report
TYPE_PRESSURE
sensor. - [C-1-2] MUST be able to deliver events at 5 Hz or greater.
- [C-1-3] MUST be temperature compensated.
- [C-SR-2] STRONGLY RECOMMENDED to be able to report pressure measurements in the range 300hPa to 1100hPa.
- SHOULD have an absolute accuracy of 1hPa.
- SHOULD have a relative accuracy of 0.12hPa over 20hPa range (equivalent to ~1m accuracy over ~200m change at sea level).
7.3.6. Termometre
If device implementations include an ambient thermometer (temperature sensor), they:
- [C-1-1] MUST define
SENSOR_TYPE_AMBIENT_TEMPERATURE
for the ambient temperature sensor and the sensor MUST measure the ambient (room/vehicle cabin) temperature from where the user is interacting with the device in degrees Celsius.
If device implementations include a thermometer sensor that measures a temperature other than ambient temperature, such as CPU temperature, they:
- [C-2-1] MUST NOT define
SENSOR_TYPE_AMBIENT_TEMPERATURE
for the temperature sensor.
If device implementations include a sensor for monitoring skin temperature, then they:
- [C-SR-1] Are STRONGLY RECOMMENDED to support the PowerManager.getThermalHeadroom API.
7.3.7. Photometer
- Device implementations MAY include a photometer (ambient light sensor).
7.3.8. Yakınlık sensörü
- Device implementations MAY include a proximity sensor.
If device implementations include a proximity sensor and they report only a binary “near” or “far” reading, they:
- [C-1-1] MUST measure the proximity of an object in the same direction as the screen. That is, the proximity sensor MUST be oriented to detect objects close to the screen, as the primary intent of this sensor type is to detect a phone in use by the user. If device implementations include a proximity sensor with any other orientation, it MUST NOT be accessible through this API.
- [C-1-2] MUST have 1-bit of accuracy or more.
- [C-1-3] MUST use 0 centimeters as the near reading and 5 centimeters as the far reading.
- [C-1-4] MUST report a maximum range and resolution of 5.
7.3.9. High Fidelity Sensors
If device implementations include a set of higher quality sensors as defined in this section, and make available them to third-party apps, they:
- [C-1-1] MUST identify the capability through the
android.hardware.sensor.hifi_sensors
feature flag.
If device implementations declare android.hardware.sensor.hifi_sensors
, they:
[C-2-1] MUST have a
TYPE_ACCELEROMETER
sensor which:- MUST have a measurement range between at least -8g and +8g, and is STRONGLY RECOMMENDED to have a measurement range between at least -16g and +16g.
- MUST have a measurement resolution of at least 2048 LSB/g.
- MUST have a minimum measurement frequency of 12.5 Hz or lower.
- MUST have a maximum measurement frequency of 400 Hz or higher; SHOULD support the SensorDirectChannel
RATE_VERY_FAST
. - MUST have a measurement noise not above 400 μg/√Hz.
- MUST implement a non-wake-up form of this sensor with a buffering capability of at least 3000 sensor events.
- MUST have a batching power consumption not worse than 3 mW.
- [C-SR-1] Is STRONGLY RECOMMENDED to have 3dB measurement bandwidth of at least 80% of Nyquist frequency, and white noise spectrum within this bandwidth.
- SHOULD have an acceleration random walk less than 30 μg √Hz tested at room temperature.
- SHOULD have a bias change vs. temperature of ≤ +/- 1 mg/°C.
- SHOULD have a best-fit line non-linearity of ≤ 0.5%, and sensitivity change vs. temperature of ≤ 0.03%/C°.
- SHOULD have cross-axis sensitivity of < 2.5 % and variation of cross-axis sensitivity < 0.2% in device operation temperature range.
[C-2-2] MUST have a
TYPE_ACCELEROMETER_UNCALIBRATED
with the same quality requirements asTYPE_ACCELEROMETER
.[C-2-3] MUST have a
TYPE_GYROSCOPE
sensor which:- MUST have a measurement range between at least -1000 and +1000 dps.
- MUST have a measurement resolution of at least 16 LSB/dps.
- MUST have a minimum measurement frequency of 12.5 Hz or lower.
- MUST have a maximum measurement frequency of 400 Hz or higher; SHOULD support the SensorDirectChannel
RATE_VERY_FAST
. - MUST have a measurement noise not above 0.014°/s/√Hz.
- [C-SR-2] Is STRONGLY RECOMMENDED to have 3dB measurement bandwidth of at least 80% of Nyquist frequency, and white noise spectrum within this bandwidth.
- SHOULD have a rate random walk less than 0.001 °/s √Hz tested at room temperature.
- SHOULD have a bias change vs. temperature of ≤ +/- 0.05 °/ s / °C.
- SHOULD have a sensitivity change vs. temperature of ≤ 0.02% / °C.
- SHOULD have a best-fit line non-linearity of ≤ 0.2%.
- SHOULD have a noise density of ≤ 0.007 °/s/√Hz.
- SHOULD have calibration error less than 0.002 rad/s in temperature range 10 ~ 40 ℃ when device is stationary.
- SHOULD have g-sensitivity less than 0.1°/s/g.
- SHOULD have cross-axis sensitivity of < 4.0 % and cross-axis sensitivity variation < 0.3% in device operation temperature range.
[C-2-4] MUST have a
TYPE_GYROSCOPE_UNCALIBRATED
with the same quality requirements asTYPE_GYROSCOPE
.[C-2-5] MUST have a
TYPE_GEOMAGNETIC_FIELD
sensor which:- MUST have a measurement range between at least -900 and +900 μT.
- MUST have a measurement resolution of at least 5 LSB/uT.
- MUST have a minimum measurement frequency of 5 Hz or lower.
- MUST have a maximum measurement frequency of 50 Hz or higher.
- MUST have a measurement noise not above 0.5 uT.
[C-2-6] MUST have a
TYPE_MAGNETIC_FIELD_UNCALIBRATED
with the same quality requirements asTYPE_GEOMAGNETIC_FIELD
and in addition:- MUST implement a non-wake-up form of this sensor with a buffering capability of at least 600 sensor events.
- [C-SR-3] Is STRONGLY RECOMMENDED to have white noise spectrum from 1 Hz to at least 10 Hz when the report rate is 50 Hz or higher.
[C-2-7] MUST have a
TYPE_PRESSURE
sensor which:- MUST have a measurement range between at least 300 and 1100 hPa.
- MUST have a measurement resolution of at least 80 LSB/hPa.
- MUST have a minimum measurement frequency of 1 Hz or lower.
- MUST have a maximum measurement frequency of 10 Hz or higher.
- MUST have a measurement noise not above 2 Pa/√Hz.
- MUST implement a non-wake-up form of this sensor with a buffering capability of at least 300 sensor events.
- MUST have a batching power consumption not worse than 2 mW.
[C-2-8] MUST have a
TYPE_GAME_ROTATION_VECTOR
sensor.[C-2-9] MUST have a
TYPE_SIGNIFICANT_MOTION
sensor which:- MUST have a power consumption not worse than 0.5 mW when device is static and 1.5 mW when device is moving.
[C-2-10] MUST have a
TYPE_STEP_DETECTOR
sensor which:- MUST implement a non-wake-up form of this sensor with a buffering capability of at least 100 sensor events.
- MUST have a power consumption not worse than 0.5 mW when device is static and 1.5 mW when device is moving.
- MUST have a batching power consumption not worse than 4 mW.
[C-2-11] MUST have a
TYPE_STEP_COUNTER
sensor which:- MUST have a power consumption not worse than 0.5 mW when device is static and 1.5 mW when device is moving.
[C-2-12] MUST have a
TILT_DETECTOR
sensor which:- MUST have a power consumption not worse than 0.5 mW when device is static and 1.5 mW when device is moving.
[C-2-13] The event timestamp of the same physical event reported by the Accelerometer, Gyroscope, and Magnetometer MUST be within 2.5 milliseconds of each other. The event timestamp of the same physical event reported by the Accelerometer and Gyroscope SHOULD be within 0.25 milliseconds of each other.
[C-2-14] MUST have Gyroscope sensor event timestamps on the same time base as the camera subsystem and within 1 milliseconds of error.
[C-2-15] MUST deliver samples to applications within 5 milliseconds from the time when the data is available on any of the above physical sensors to the application.
[C-2-16] MUST NOT have a power consumption higher than 0.5 mW when device is static and 2.0 mW when device is moving when any combination of the following sensors are enabled:
-
SENSOR_TYPE_SIGNIFICANT_MOTION
-
SENSOR_TYPE_STEP_DETECTOR
-
SENSOR_TYPE_STEP_COUNTER
-
SENSOR_TILT_DETECTORS
-
[C-2-17] MAY have a
TYPE_PROXIMITY
sensor, but if present MUST have a minimum buffer capability of 100 sensor events.
Note that all power consumption requirements in this section do not include the power consumption of the Application Processor. It is inclusive of the power drawn by the entire sensor chain—the sensor, any supporting circuitry, any dedicated sensor processing system, etc.
If device implementations include direct sensor support, they:
- [C-3-1] MUST correctly declare support of direct channel types and direct report rates level through the
isDirectChannelTypeSupported
andgetHighestDirectReportRateLevel
API. - [C-3-2] MUST support at least one of the two sensor direct channel types for all sensors that declare support for sensor direct channel.
- SHOULD support event reporting through sensor direct channel for primary sensor (non-wakeup variant) of the following types:
-
TYPE_ACCELEROMETER
-
TYPE_ACCELEROMETER_UNCALIBRATED
-
TYPE_GYROSCOPE
-
TYPE_GYROSCOPE_UNCALIBRATED
-
TYPE_MAGNETIC_FIELD
-
TYPE_MAGNETIC_FIELD_UNCALIBRATED
-
7.3.10. Biometric Sensors
For additional background on Measuring Biometric Unlock Security, please see Measuring Biometric Security documentation .
If device implementations include a secure lock screen, they:
- SHOULD include a biometric sensor
Biometric sensors can be classified as Class 3 (formerly Strong ), Class 2 (formerly Weak ), or Class 1 (formerly Convenience ) based on their spoof and imposter acceptance rates, and on the security of the biometric pipeline. This classification determines the capabilities the biometric sensor has to interface with the platform and with third-party applications. Sensors are classified as Class 1 by default, and need to meet additional requirements as detailed below if they wish to be classified as either Class 2 or Class 3 . Both Class 2 and Class 3 biometrics get additional capabilities as detailed below.
If device implementations make a biometric sensor available to third-party applications via android.hardware.biometrics.BiometricManager , android.hardware.biometrics.BiometricPrompt , and android.provider.Settings.ACTION_BIOMETRIC_ENROLL , they:
- [C-4-1] MUST meet the requirements for Class 3 or Class 2 biometric as defined in this document.
- [C-4-2] MUST recognize and honor each parameter name defined as a constant in the Authenticators class and any combinations thereof. Conversely, MUST NOT honor or recognize integer constants passed to the canAuthenticate(int) and setAllowedAuthenticators(int) methods other than those documented as public constants in Authenticators and any combinations thereof.
- [C-4-3] MUST implement the ACTION_BIOMETRIC_ENROLL action on devices that have either Class 3 or Class 2 biometrics. This action MUST only present the enrollment entry points for Class 3 or Class 2 biometrics.
If device implementations support passive biometrics, they:
- [C-5-1] MUST by default require an additional confirmation step (eg a button press).
- [C-SR-1] Are STRONGLY RECOMMENDED to have a setting to allow users to override application preference and always require accompanying confirmation step.
- [C-SR-2] Are STRONGLY RECOMMENDED to have the confirm action be secured such that an operating system or kernel compromise cannot spoof it. For example, this means that the confirm action based on a physical button is routed through an input-only general-purpose input/output (GPIO) pin of a secure element (SE) that cannot be driven by any other means than a physical button basmak.
- [C-5-2] MUST additionally implement an implicit authentication flow (without confirmation step) corresponding to setConfirmationRequired(boolean) , which applications can set to utilize for sign-in flows.
If device implementations have multiple biometric sensors, they:
- [C-SR-3] Are STRONGLY RECOMMENDED to require only one biometric be confirmed per authentication (eg if both fingerprint and face sensors are available on the device, onAuthenticationSucceeded should be sent after any one of them is confirmed).
In order for device implementations to allow access to keystore keys to third-party applications, they:
- [C-6-1] MUST meet the requirements for Class 3 as defined in this section below.
- [C-6-2] MUST present only Class 3 biometrics when the authentication requires BIOMETRIC_STRONG , or the authentication is invoked with a CryptoObject .
If device implementations wish to treat a biometric sensor as Class 1 (formerly Convenience ), they:
- [C-1-1] MUST have a false acceptance rate less than 0.002%.
- [C-1-2] MUST disclose that this mode may be less secure than a strong PIN, pattern, or password and clearly enumerate the risks of enabling it, if the spoof and imposter acceptance rates are higher than 7% as measured by the Android Biometrics Test Protocols .
- [C-1-9] MUST challenge the user for the recommended primary authentication (eg PIN, pattern, password) after no more than twenty false trials and no less than ninety-second backoff time for biometric verification - where a false trial is one with an adequate capture quality (BIOMETRIC_ACQUIRED_GOOD) that does not match an enrolled biometric.
- [C-SR-4] Are STRONGLY RECOMMENDED to lower the total number of false trials for biometric verification specified in [C-1-9] if the spoof and imposter acceptance rates are higher than 7% as measure by the Android Biometrics Test Protocols .
- [C-1-3] MUST rate limit attempts for biometric verification - where a false trial is one with an adequate capture quality (
BIOMETRIC_ACQUIRED_GOOD
) that does not match an enrolled biometric. - [C-SR-5] Are STRONGLY RECOMMENDED to rate limit attempts for at least 30 seconds after five false trials for biometric verification for the maximum number of false trials per [C-1-9] - where a false trial is one with an adequate capture quality (BIOMETRIC_ACQUIRED_GOOD) that does not match an enrolled biometric.
- [C-SR-6] Are STRONGLY RECOMMENDED to have all rate limiting logic in TEE.
- [C-1-10] MUST disable biometrics once primary authentication backoff has first triggered as described in [C-0-2] of section 9.11.
- [C-1-4] MUST prevent adding new biometrics without first establishing a chain of trust by having the user confirm existing or add a new device credential (PIN/pattern/password) that's secured by TEE; the Android Open Source Project implementation provides the mechanism in the framework to do so.
- [C-1-5] MUST completely remove all identifiable biometric data for a user when the user's account is removed (including via a factory reset).
- [C-1-6] MUST honor the individual flag for that biometric (ie
DevicePolicyManager.KEYGUARD_DISABLE_FINGERPRINT
,DevicePolicymanager.KEYGUARD_DISABLE_FACE
, orDevicePolicymanager.KEYGUARD_DISABLE_IRIS
). - [C-1-7] MUST challenge the user for the recommended primary authentication (eg PIN, pattern, password): a) once every 24 hours or less for devices launching with Android version 9 or later, or b) once every 72 hours or less for devices upgrading from Android 8 or earlier.
[C-1-8] MUST challenge the user for the recommended primary authentication (eg: PIN, pattern, password) or Class 3 (STRONG) biometric after one of the following:
- a 4-hour idle timeout period, OR
3 failed biometric authentication attempts.
[C-SR-7] Are STRONGLY RECOMMENDED to use the logic in the framework provided by the Android Open Source Project to enforce constraints specified in [C-1-7] and [C-1-8] for new devices.
[C-SR-8] Are STRONGLY RECOMMENDED to have a false rejection rate of less than 10%, as measured on the device.
[C-SR-9] Are STRONGLY RECOMMENDED to have a latency below 1 second, measured from when the biometric is detected, until the screen is unlocked, for each enrolled biometric.
If device implementations wish to treat a biometric sensor as Class 2 (formerly Weak ), they:
- [C-2-1] MUST meet all requirements for Class 1 above.
- [C-2-2] MUST have a spoof and imposter acceptance rate not higher than 20% as measured by the Android Biometrics Test Protocols .
- [C-2-3] MUST perform the biometric matching in an isolated execution environment outside Android user or kernel space, such as the Trusted Execution Environment (TEE), or on a chip with a secure channel to the isolated execution environment.
- [C-2-4] MUST have all identifiable data encrypted and cryptographically authenticated such that they cannot be acquired, read or altered outside of the isolated execution environment or a chip with a secure channel to the isolated execution environment as documented in the implementation guidelines on the Android Open Source Project site.
- [C-2-5] For camera based biometrics, while biometric based authentication or enrollment is happening:
- MUST operate the camera in a mode that prevents camera frames from being read or altered outside the isolated execution environment or a chip with a secure channel to the isolated execution environment.
- For RGB single-camera solutions, the camera frames CAN be readable outside the isolated execution environment to support operations such as preview for enrollment, but MUST still NOT be alterable.
- [C-2-6] MUST NOT enable third-party applications to distinguish between individual biometric enrollments.
- [C-2-7] MUST NOT allow unencrypted access to identifiable biometric data or any data derived from it (such as embeddings) to the Application Processor outside the context of the TEE. Upgrading devices launched on Android version 9 or earlier are not exempted from C-2-7.
[C-2-8] MUST have a secure processing pipeline such that an operating system or kernel compromise cannot allow data to be directly injected to falsely authenticate as the user.
[C-SR-10] Are STRONGLY RECOMMENDED to include liveness detection for all biometric modalities and attention detection for Face biometrics.
[C-2-9] MUST make the biometric sensor available to third-party applications.
If device implementations wish to treat a biometric sensor as Class 3 (formerly Strong ), they:
- [C-3-1] MUST meet all the requirements of Class 2 above, except for [C-1-7] and [C-1-8].
- [C-3-2] MUST have a hardware-backed keystore implementation.
- [C-3-3] MUST have a spoof and imposter acceptance rate not higher than 7% as measured by the Android Biometrics Test Protocols .
- [C-3-4] MUST challenge the user for the recommended primary authentication (eg PIN, pattern, password) once every 72 hours or less.
- [C-3-5] MUST re-generate Authenticator ID for all Class 3 biometrics supported on device if any of them is re-enrolled.
- [C-3-6] Must enable biometric-backed keystore keys to third-party applications.
If device implementations contain an under-display fingerprint sensor (UDFPS), they:
- [C-SR-11] Are STRONGLY RECOMMENDED to prevent the touchable area of the UDFPS from interfering with 3-button navigation( which some users might require for accessibility purposes).
7.3.12. Pose Sensor
Cihaz uygulamaları:
- MAY support pose sensor with 6 degrees of freedom.
If device implementations support pose sensor with 6 degrees of freedom, they:
- [C-1-1] MUST implement and report
TYPE_POSE_6DOF
sensor. - [C-1-2] MUST be more accurate than the rotation vector alone.
7.3.13. Hinge Angle Sensor
If device implementations support a hinge angle sensor, they:
- [C-1-1] MUST implement and report
TYPE_HINGLE_ANGLE
. - [C-1-2] MUST support at least two readings between 0 and 360 degrees (inclusive ie including 0 and 360 degrees).
- [C-1-3] MUST return a wakeup sensor for
getDefaultSensor(SENSOR_TYPE_HINGE_ANGLE)
.
7.4. Data Connectivity
7.4.1. Telefon
“Telephony” as used by the Android APIs and this document refers specifically to hardware related to placing voice calls and sending SMS messages via a GSM or CDMA network. While these voice calls may or may not be packet-switched, they are for the purposes of Android considered independent of any data connectivity that may be implemented using the same network. In other words, the Android “telephony” functionality and APIs refer specifically to voice calls and SMS. For instance, device implementations that cannot place calls or send/receive SMS messages are not considered a telephony device, regardless of whether they use a cellular network for data connectivity.
- Android MAY be used on devices that do not include telephony hardware. That is, Android is compatible with devices that are not phones.
If device implementations include GSM or CDMA telephony, they:
- [C-1-1] MUST declare the
android.hardware.telephony
feature flag and other sub-feature flags according to the technology. - [C-1-2] MUST implement full support for the API for that technology.
- SHOULD allow all available cellular service types (2G, 3G, 4G, 5G, etc.) during emergency calls (regardless of the network types set by
SetAllowedNetworkTypeBitmap()
).
If device implementations do not include telephony hardware, they:
- [C-2-1] MUST implement the full APIs as no-ops.
If device implementations support eUICCs or eSIMs/embedded SIMs and include a proprietary mechanism to make eSIM functionality available for third-party developers, they:
- [C-3-1] MUST provide a complete implementation of the
EuiccManager API
.
If device implementations don't set the system property ro.telephony.iwlan\_operation\_mode
to 'legacy', then they:
- [C-4-1] MUST NOT report ' NETWORK_TYPE_IWLAN ' via NetworkRegistrationInfo#getAccessNetworkTechnology() when NetworkRegistrationInfo#getTransportType() is reported as ' TRANSPORT_TYPE_WWAN ' for the same NetworkRegistrationInfo instance.
If device implementations support a single IP Multimedia Subsystem (IMS) registration for both multimedia telephony service (MMTEL) and rich communication service (RCS) features and are expected to comply with cellular carrier requirements regarding using a single IMS registration for all IMS signalling traffic, Onlar:
- [C-5-1] MUST declare the
android.hardware.telephony.ims
feature flag and provide a complete implementation of the ImsService API for both MMTEL and RCS User Capability Exchange API . - [C-5-2] MUST declare the
android.hardware.telephony.ims.singlereg
feature flag and provide a complete implementation of the SipTransport API , the GbaService API , dedicated bearer indications using the IRadio 1.6 HAL, and provisioning via Auto Configuration Server (ACS) or other proprietary provisioning mechanism using the IMS Configuration API .
7.4.1.1. Number Blocking Compatibility
If device implementations report the android.hardware.telephony feature
, they:
- [C-1-1] MUST include number blocking support
- [C-1-2] MUST fully implement
BlockedNumberContract
and the corresponding API as described in the SDK documentation. - [C-1-3] MUST block all calls and messages from a phone number in 'BlockedNumberProvider' without any interaction with apps. The only exception is when number blocking is temporarily lifted as described in the SDK documentation.
- [C-1-4] MUST NOT write to the platform call log provider for a blocked call.
- [C-1-5] MUST NOT write to the Telephony provider for a blocked message.
- [C-1-6] MUST implement a blocked numbers management UI, which is opened with the intent returned by
TelecomManager.createManageBlockedNumbersIntent()
method. - [C-1-7] MUST NOT allow secondary users to view or edit the blocked numbers on the device as the Android platform assumes the primary user to have full control of the telephony services, a single instance, on the device. All blocking related UI MUST be hidden for secondary users and the blocked list MUST still be respected.
- SHOULD migrate the blocked numbers into the provider when a device updates to Android 7.0.
7.4.1.2. Telecom API
If device implementations report android.hardware.telephony
, they:
- [C-1-1] MUST support the
ConnectionService
APIs described in the SDK . - [C-1-2] MUST display a new incoming call and provide user affordance to accept or reject the incoming call when the user is on an ongoing call that is made by a third-party app that does not support the hold feature specified via
CAPABILITY_SUPPORT_HOLD
. - [C-1-3] MUST have an application that implements InCallService .
[C-SR-1] Are STRONGLY RECOMMENDED to notify the user that answering an incoming call will drop an ongoing call.
The AOSP implementation meets these requirements by a heads-up notification which indicates to the user that answering an incoming call will cause the other call to be dropped.
[C-SR-1] Are STRONGLY RECOMMENDED to preload the default dialer app that shows a call log entry and the name of a third-party app in its call log when the third-party app sets the
EXTRA_LOG_SELF_MANAGED_CALLS
extras key on itsPhoneAccount
totrue
.[C-SR-2] Are STRONGLY RECOMMENDED to handle the audio headset's
KEYCODE_MEDIA_PLAY_PAUSE
andKEYCODE_HEADSETHOOK
events for theandroid.telecom
APIs as below:- Call
Connection.onDisconnect()
when a short press of the key event is detected during an ongoing call. - Call
Connection.onAnswer()
when a short press of the key event is detected during an incoming call. - Call
Connection.onReject()
when a long press of the key event is detected during an incoming call. - Toggle the mute status of the
CallAudioState
.
- Call
7.4.2. IEEE 802.11 (Wi-Fi)
Cihaz uygulamaları:
- SHOULD include support for one or more forms of 802.11.
If device implementations include support for 802.11 and expose the functionality to a third-party application, they:
- [C-1-1] MUST implement the corresponding Android API.
- [C-1-2] MUST report the hardware feature flag
android.hardware.wifi
. - [C-1-3] MUST implement the multicast API as described in the SDK documentation.
- [C-1-4] MUST support multicast DNS (mDNS) and MUST NOT filter mDNS packets (224.0.0.251) at any time of operation including:
- Even when the screen is not in an active state.
- For Android Television device implementations, even when in standby power states.
- [C-1-5] MUST NOT treat the
WifiManager.enableNetwork()
API method call as a sufficient indication to switch the currently activeNetwork
that is used by default for application traffic and is returned byConnectivityManager
API methods such asgetActiveNetwork
andregisterDefaultNetworkCallback
. In other words, they MAY only disable the Internet access provided by any other network provider (eg mobile data) if they successfully validate that the Wi-Fi network is providing Internet access. - [C-1-6] Are STRONGLY RECOMMENDED to, when the
ConnectivityManager.reportNetworkConnectivity()
API method is called, re-evaluate the Internet access on theNetwork
and, once the evaluation determines that the currentNetwork
no longer provides Internet access, switch to any other available network (eg mobile data) that provides Internet access. - [C-1-7] MUST randomize the source MAC address and sequence number of probe request frames, once at the beginning of each scan, while STA is disconnected.
- [C-1-8] MUST use one consistent MAC address (SHOULD NOT randomize MAC address halfway through a scan).
- [C-1-9] MUST iterate probe request sequence number as normal (sequentially) between the probe requests in a scan.
- [C-1-10] MUST randomize Probe request sequence number between the last probe request of a scan and the first probe request of the next scan.
- [C-SR-1] Are STRONGLY RECOMMENDED to randomize the source MAC address used for all STA communication to an Access Point (AP) while associating and associated.
- The device MUST use a different randomized MAC address for each SSID (FQDN for Passpoint) it communicates with.
- The device MUST provide the user with an option to control the randomization per SSID (FQDN for Passpoint) with non randomized and randomized options, and MUST set the default mode for new Wi-Fi configurations to be randomized.
- [C-SR-2] Are STRONGLY RECOMMENDED to use a random BSSID for any AP that they create.
- The MAC address MUST be randomized and persisted per SSID used by the AP.
- The DEVICE MAY provide the user with an option to disable this feature. If such an option is provided, randomization MUST be enabled by default.
If device implementations include support for Wi-Fi power save mode as defined in IEEE 802.11 standard, they:
- SHOULD turn off Wi-Fi power save mode whenever an app acquires
WIFI_MODE_FULL_HIGH_PERF
lock orWIFI_MODE_FULL_LOW_LATENCY
lock viaWifiManager.createWifiLock()
andWifiManager.WifiLock.acquire()
APIs and the lock is active. - [C-3-2] The average round trip latency between the device and an access point while the device is in a Wi-Fi Low Latency Lock (
WIFI_MODE_FULL_LOW_LATENCY
) mode MUST be smaller than the latency during a Wi-Fi High Perf Lock (WIFI_MODE_FULL_HIGH_PERF
) mode. - [C-SR-3] Are STRONGLY RECOMMENDED to minimize Wi-Fi round trip latency whenever a Low Latency Lock (
WIFI_MODE_FULL_LOW_LATENCY
) is acquired and takes effect.
If device implementations support Wi-Fi and use Wi-Fi for location scanning, they:
- [C-2-1] MUST provide a user affordance to enable/disable the value read through the
WifiManager.isScanAlwaysAvailable
API method.
7.4.2.1. Doğrudan kablosuz bağlantı
Cihaz uygulamaları:
- SHOULD include support for Wi-Fi Direct (Wi-Fi peer-to-peer).
If device implementations include support for Wi-Fi Direct, they:
- [C-1-1] MUST implement the corresponding Android API as described in the SDK documentation.
- [C-1-2] MUST report the hardware feature
android.hardware.wifi.direct
. - [C-1-3] MUST support regular Wi-Fi operation.
- [C-1-4] MUST support Wi-Fi and Wi-Fi Direct operations concurrently.
- [C-SR-1] Are STRONGLY RECOMMENDED to randomize the source MAC address for all newly formed Wi-Fi Direct connections.
7.4.2.2. Wi-Fi Tunneled Direct Link Setup
Cihaz uygulamaları:
- SHOULD include support for Wi-Fi Tunneled Direct Link Setup (TDLS) as described in the Android SDK Documentation.
If device implementations include support for TDLS and TDLS is enabled by the WiFiManager API, they:
- [C-1-1] MUST declare support for TDLS through
WifiManager.isTdlsSupported
. - SHOULD use TDLS only when it is possible AND beneficial.
- SHOULD have some heuristic and NOT use TDLS when its performance might be worse than going through the Wi-Fi access point.
7.4.2.3. Wi-Fi Aware
Cihaz uygulamaları:
- SHOULD include support for Wi-Fi Aware .
If device implementations include support for Wi-Fi Aware and expose the functionality to third-party apps, then they:
- [C-1-1] MUST implement the
WifiAwareManager
APIs as described in the SDK documentation . - [C-1-2] MUST declare the
android.hardware.wifi.aware
feature flag. - [C-1-3] MUST support Wi-Fi and Wi-Fi Aware operations concurrently.
- [C-1-4] MUST randomize the Wi-Fi Aware management interface address at intervals no longer than 30 minutes and whenever Wi-Fi Aware is enabled unless an Aware ranging operation is ongoing or an Aware data-path is active (randomization is not expected for as long as the data-path is active).
If device implementations include support for Wi-Fi Aware and Wi-Fi Location as described in Section 7.4.2.5 and exposes these functionalities to third-party apps, then they:
- [C-2-1] MUST implement the location-aware discovery APIs: setRangingEnabled , setMinDistanceMm , setMaxDistanceMm , and onServiceDiscoveredWithinRange .
7.4.2.4. Wi-Fi Passpoint
If device implementations include support for 802.11 (Wi-Fi) they:
- [C-1-1] MUST include support for Wi-Fi Passpoint .
- [C-1-2] MUST implement the Passpoint related
WifiManager
APIs as described in the SDK documentation . - [C-1-3] MUST support IEEE 802.11u standard, specifically related to Network Discovery and Selection, such as Generic Advertisement Service (GAS) and Access Network Query Protocol (ANQP).
- [C-1-4] MUST declare
android.hardware.wifi.passpoint
feature flag. - [C-1-5] MUST follow the AOSP implementation to discover, match and associate to Passpoint networks.
- [C-1-6] MUST support at least the following subset of device provisioning protocols as defined in the Wi-Fi Alliance Passpoint R2: EAP-TTLS authentication and SOAP-XML.
- [C-1-7] MUST process the AAA server certificate as described in Hotspot 2.0 R3 specification.
- [C-1-8] MUST support user control of provisioning through the Wi-Fi picker.
- [C-1-9] MUST keep Passpoint configurations persistent across reboots.
- [C-SR-1] Are STRONGLY RECOMMENDED to support the terms and conditions acceptance feature.
- [C-SR-2] Are STRONGLY RECOMMENDED to support the Venue information feature.
Conversely if device implementations do not include support for Wi-Fi Passpoint:
- [C-2-1] The implementation of the Passpoint related
WifiManager
APIs MUST throw anUnsupportedOperationException
.
If a global Passpoint disable user control switch is provided, implementations:
- [C-3-1] MUST enable Passpoint by default.
7.4.2.5. Wi-Fi Location (Wi-Fi Round Trip Time - RTT)
Cihaz uygulamaları:
- SHOULD include support for Wi-Fi Location .
If device implementations include support for Wi-Fi Location and expose the functionality to third-party apps, then they:
- [C-1-1] MUST implement the
WifiRttManager
APIs as described in the SDK documentation . - [C-1-2] MUST declare the
android.hardware.wifi.rtt
feature flag. - [C-1-3] MUST randomize the source MAC address for each RTT burst which is executed while the Wi-Fi interface on which the RTT is being executed is not associated to an Access Point.
- [C-1-4] MUST be accurate to within 2 meters at 80 MHz bandwidth at the 68th percentile (as calculated with the Cumulative Distribution Function).
7.4.2.6. Wi-Fi Keepalive Offload
Cihaz uygulamaları:
- SHOULD include support for Wi-Fi keepalive offload.
If device implementations include support for Wi-Fi keepalive offload and expose the functionality to third-party apps, they:
[C-1-1] MUST support the SocketKeepAlive API.
[C-1-2] MUST support at least three concurrent keepalive slots over Wi-Fi and at least one keepalive slot over cellular.
If device implementations do not include support for Wi-Fi keepalive offload, they:
- [C-2-1] MUST return
ERROR_UNSUPPORTED
.
7.4.2.7. Wi-Fi Easy Connect (Device Provisioning Protocol)
Cihaz uygulamaları:
- SHOULD include support for Wi-Fi Easy Connect (DPP) .
Cihaz uygulamaları Wi-Fi kolay bağlantı için destek içeriyorsa ve işlevselliği üçüncü taraf uygulamalara maruz bırakın:
- [C-1-1] MUST have the WifiManager#isEasyConnectSupported() method return
true
.
7.4.2.8. Enterprise Wi-Fi Server Certificate Validation
If the Wi-Fi server certificate is not validated or the Wi-Fi server domain name is not set, device implementations:
- [C-SR-1] are STRONGLY RECOMMENDED not to provide the user an option to manually add Enterprise Wi-Fi network in the Settings app.
7.4.3. Bluetooth
If device implementations support Bluetooth Audio profile, they:
- SHOULD support Advanced Audio Codecs and Bluetooth Audio Codecs (eg LDAC).
If device implementations support HFP, A2DP and AVRCP, they:
- SHOULD support at least 5 total connected devices.
If device implementations declare android.hardware.vr.high_performance
feature, they:
- [C-1-1] MUST support Bluetooth 4.2 and Bluetooth LE Data Length Extension.
Android includes support for Bluetooth and Bluetooth Low Energy .
If device implementations include support for Bluetooth and Bluetooth Low Energy, they:
- [C-2-1] MUST declare the relevant platform features (
android.hardware.bluetooth
andandroid.hardware.bluetooth_le
respectively) and implement the platform APIs. - SHOULD implement relevant Bluetooth profiles such as A2DP, AVRCP, OBEX, HFP, etc. as appropriate for the device.
If device implementations include support for Bluetooth Low Energy (BLE), they:
- [C-3-1] MUST declare the hardware feature
android.hardware.bluetooth_le
. - [C-3-2] MUST enable the GATT (generic attribute profile) based Bluetooth APIs as described in the SDK documentation and android.bluetooth .
- [C-3-3] MUST report the correct value for
BluetoothAdapter.isOffloadedFilteringSupported()
to indicate whether the filtering logic for the ScanFilter API classes is implemented. - [C-3-4] MUST report the correct value for
BluetoothAdapter.isMultipleAdvertisementSupported()
to indicate whether Low Energy Advertising is supported. - [C-3-5] MUST implement a Resolvable Private Address (RPA) timeout no longer than 15 minutes and rotate the address at timeout to protect user privacy when device is actively using BLE for scanning or advertising. To prevent timing attacks, timeout intervals MUST also be randomized between 5 and 15 minutes.
- SHOULD support offloading of the filtering logic to the bluetooth chipset when implementing the ScanFilter API .
- SHOULD support offloading of the batched scanning to the bluetooth chipset.
- SHOULD support multi advertisement with at least 4 slots.
If device implementations support Bluetooth LE and use Bluetooth LE for location scanning, they:
- [C-4-1] MUST provide a user affordance to enable/disable the value read through the System API
BluetoothAdapter.isBleScanAlwaysAvailable()
.
If device implementations include support for Bluetooth LE and Hearing Aids Profile, as described in Hearing Aid Audio Support Using Bluetooth LE , they:
- [C-5-1] MUST return
true
for BluetoothAdapter.getProfileProxy(context, listener, BluetoothProfile.HEARING_AID) .
If device implementations include support for Bluetooth or Bluetooth Low Energy, they:
- [C-6-1] MUST restrict access to any Bluetooth metadata (such as scan results) which could be used to derive the location of the device, unless the requesting app successfully passes an
android.permission.ACCESS_FINE_LOCATION
permission check based on its current foreground/background state.
If device implementations include support for Bluetooth or Bluetooth Low Energy and the app manifest does not include a declaration from the developer stating that they are not deriving location from Bluetooth, then, they:
- [C-6-2] MUST gate Bluetooth access behind the
android.permission.ACCESS_FINE_LOCATION
.
7.4.4. Near-Field Communications
Cihaz uygulamaları:
- SHOULD include a transceiver and related hardware for Near-Field Communications (NFC).
- [C-0-1] MUST implement
android.nfc.NdefMessage
andandroid.nfc.NdefRecord
APIs even if they do not include support for NFC or declare theandroid.hardware.nfc
feature as the classes represent a protocol-independent data representation format .
If device implementations include NFC hardware and plan to make it available to third-party apps, they:
- [C-1-1] MUST report the
android.hardware.nfc
feature from theandroid.content.pm.PackageManager.hasSystemFeature()
method . - MUST be capable of reading and writing NDEF messages via the following NFC standards as below:
- [C-1-2] MUST be capable of acting as an NFC Forum reader/writer (as defined by the NFC Forum technical specification NFCForum-TS-DigitalProtocol-1.0) via the following NFC standards:
- NfcA (ISO14443-3A)
- NfcB (ISO14443-3B)
- NfcF (JIS X 6319-4)
- IsoDep (ISO 14443-4)
- NFC Forum Tag Types 1, 2, 3, 4, 5 (defined by the NFC Forum)
[C-SR-1] STRONGLY RECOMMENDED to be capable of reading and writing NDEF messages as well as raw data via the following NFC standards. Note that while the NFC standards are stated as STRONGLY RECOMMENDED, the Compatibility Definition for a future version is planned to change these to MUST. These standards are optional in this version but will be required in future versions. Existing and new devices that run this version of Android are very strongly encouraged to meet these requirements now so they will be able to upgrade to the future platform releases.
[C-1-13] MUST poll for all supported technologies while in NFC discovery mode.
SHOULD be in NFC discovery mode while the device is awake with the screen active and the lock-screen unlocked.
SHOULD be capable of reading the barcode and URL (if encoded) of Thinfilm NFC Barcode products.
Note that publicly available links are not available for the JIS, ISO, and NFC Forum specifications cited above.
Android includes support for NFC Host Card Emulation (HCE) mode.
If device implementations include an NFC controller chipset capable of HCE (for NfcA and/or NfcB) and support Application ID (AID) routing, they:
- [C-2-1] MUST report the
android.hardware.nfc.hce
feature constant. - [C-2-2] MUST support NFC HCE APIs as defined in the Android SDK.
If device implementations include an NFC controller chipset capable of HCE for NfcF, and implement the feature for third-party applications, they:
- [C-3-1] MUST report the
android.hardware.nfc.hcef
feature constant. - [C-3-2] MUST implement the NfcF Card Emulation APIs as defined in the Android SDK.
If device implementations include general NFC support as described in this section and support MIFARE technologies (MIFARE Classic, MIFARE Ultralight, NDEF on MIFARE Classic) in the reader/writer role, they:
- [C-4-1] MUST implement the corresponding Android APIs as documented by the Android SDK.
- [C-4-2] MUST report the feature
com.nxp.mifare
from theandroid.content.pm.PackageManager.hasSystemFeature
() method. Note that this is not a standard Android feature and as such does not appear as a constant in theandroid.content.pm.PackageManager
class.
7.4.5. Networking protocols and APIs
7.4.5.1. Minimum Network Capability
Cihaz uygulamaları:
- [C-0-1] MUST include support for one or more forms of data networking. Specifically, device implementations MUST include support for at least one data standard capable of 200 Kbit/sec or greater. Examples of technologies that satisfy this requirement include EDGE, HSPA, EV-DO, 802.11g, Ethernet and Bluetooth PAN.
- SHOULD also include support for at least one common wireless data standard, such as 802.11 (Wi-Fi), when a physical networking standard (such as Ethernet) is the primary data connection.
- MAY implement more than one form of data connectivity.
7.4.5.2. IPv6
Cihaz uygulamaları:
- [C-0-2] MUST include an IPv6 networking stack and support IPv6 communication using the managed APIs, such as
java.net.Socket
andjava.net.URLConnection
, as well as the native APIs, such asAF_INET6
sockets. - [C-0-3] MUST enable IPv6 by default.
- MUST ensure that IPv6 communication is as reliable as IPv4, for example:
- [C-0-4] MUST maintain IPv6 connectivity in doze mode.
- [C-0-5] Rate-limiting MUST NOT cause the device to lose IPv6 connectivity on any IPv6-compliant network that uses RA lifetimes of at least 180 seconds.
- MUST ensure that IPv6 communication is as reliable as IPv4, for example:
- [C-0-6] MUST provide third-party applications with direct IPv6 connectivity to the network when connected to an IPv6 network, without any form of address or port translation happening locally on the device. Both managed APIs such as
Socket#getLocalAddress
orSocket#getLocalPort
) and NDK APIs such asgetsockname()
orIPV6_PKTINFO
MUST return the IP address and port that is actually used to send and receive packets on the network and is visible as the source ip and port to internet (web) servers.
The required level of IPv6 support depends on the network type, as shown in the following requirements.
If device implementations support Wi-Fi, they:
- [C-1-1] MUST support dual-stack and IPv6-only operation on Wi-Fi.
If device implementations support Ethernet, they:
- [C-2-1] MUST support dual-stack and IPv6-only operation on Ethernet.
If device implementations support Cellular data, they:
- [C-3-1] MUST support IPv6 operation (IPv6-only and possibly dual-stack) on cellular.
If device implementations support more than one network type (eg, Wi-Fi and cellular data), they:
- [C-4-1] MUST simultaneously meet the above requirements on each network when the device is simultaneously connected to more than one network type.
7.4.5.3. Captive Portals
A captive portal refers to a network that requires sign-in in order to obtain internet access.
If device implementations provide a complete implementation of the android.webkit.Webview API
, they:
- [C-1-1] MUST provide a captive portal application to handle the intent
ACTION_CAPTIVE_PORTAL_SIGN_IN
and display the captive portal login page, by sending that intent, on call to the System APIConnectivityManager#startCaptivePortalApp(Network, Bundle)
. - [C-1-2] MUST perform detection of captive portals and support login through the captive portal application when the device is connected to any network type, including cellular/mobile network, WiFi, Ethernet or Bluetooth.
- [C-1-3] MUST support logging in to captive portals using cleartext DNS when the device is configured to use private DNS strict mode.
- [C-1-4] MUST use encrypted DNS as per the SDK documentation for
android.net.LinkProperties.getPrivateDnsServerName
andandroid.net.LinkProperties.isPrivateDnsActive
for all network traffic that is not explicitly communicating with the captive portal. - [C-1-5] MUST ensure that, while the user is logging in to a captive portal, the default network used by applications (as returned by
ConnectivityManager.getActiveNetwork
,ConnectivityManager.registerDefaultNetworkCallback
, and used by default by Java networking APIs such as java.net.Socket, and native APIs such as connect()) is any other available network that provides internet access, if available.
7.4.6. Sync Settings
Cihaz uygulamaları:
- [C-0-1] MUST have the master auto-sync setting on by default so that the method
getMasterSyncAutomatically()
returns “true”.
7.4.7. Veri Tasarrufu
If device implementations include a metered connection, they are:
- [C-SR-1] STRONGLY RECOMMENDED to provide the data saver mode.
If device implementations provide the data saver mode, they:
- [C-1-1] MUST support all the APIs in the
ConnectivityManager
class as described in the SDK documentation
Cihaz uygulamaları veri tasarrufu modunu sağlamazsa, bunlar:
- [C-2-1] MUST return the value
RESTRICT_BACKGROUND_STATUS_DISABLED
forConnectivityManager.getRestrictBackgroundStatus()
- [C-2-2] MUST NOT broadcast
ConnectivityManager.ACTION_RESTRICT_BACKGROUND_CHANGED
.
7.4.8. Secure Elements
If device implementations support Open Mobile API -capable secure elements and make them available to third-party apps, they:
[C-1-1] MUST enumerate the available secure elements readers via
android.se.omapi.SEService.getReaders()
API.[C-1-2] MUST declare the correct feature flags via
android.hardware.se.omapi.uicc
for the device with UICC-based secure elements,android.hardware.se.omapi.ese
for the device with eSE-based secure elements andandroid.hardware.se.omapi.sd
for the device with SD-based secure elements.
7.5. Kameralar
If device implementations include at least one camera, they:
- [C-1-1] MUST declare the
android.hardware.camera.any
feature flag. - [C-1-2] MUST be possible for an application to simultaneously allocate 3 RGBA_8888 bitmaps equal to the size of the images produced by the largest-resolution camera sensor on the device, while camera is open for the purpose of basic preview and still esir almak.
- [C-1-3] MUST ensure that the preinstalled default camera application handling intents
MediaStore.ACTION_IMAGE_CAPTURE
,MediaStore.ACTION_IMAGE_CAPTURE_SECURE
, orMediaStore.ACTION_VIDEO_CAPTURE
, is responsible for removing the user location in the image metadata before sending it to the receiving application when the receiving application does not haveACCESS_FINE_LOCATION
.
7.5.1. Arka yüz kamerası
A rear-facing camera is a camera located on the side of the device opposite the display; that is, it images scenes on the far side of the device, like a traditional camera.
Cihaz uygulamaları:
- SHOULD include a rear-facing camera.
If device implementations include at least one rear-facing camera, they:
- [C-1-1] MUST report the feature flag
android.hardware.camera
andandroid.hardware.camera.any
. - [C-1-2] MUST have a resolution of at least 2 megapixels.
- SHOULD have either hardware auto-focus or software auto-focus implemented in the camera driver (transparent to application software).
- MAY have fixed-focus or EDOF (extended depth of field) hardware.
- MAY include a flash.
If the camera includes a flash:
- [C-2-1] the flash lamp MUST NOT be lit while an
android.hardware.Camera.PreviewCallback
instance has been registered on a Camera preview surface, unless the application has explicitly enabled the flash by enabling theFLASH_MODE_AUTO
orFLASH_MODE_ON
attributes of aCamera.Parameters
object. Note that this constraint does not apply to the device's built-in system camera application, but only to third-party applications usingCamera.PreviewCallback
.
7.5.2. Ön kamera
A front-facing camera is a camera located on the same side of the device as the display; that is, a camera typically used to image the user, such as for video conferencing and similar applications.
Cihaz uygulamaları:
- MAY include a front-facing camera.
If device implementations include at least one front-facing camera, they:
- [C-1-1] MUST report the feature flag
android.hardware.camera.any
andandroid.hardware.camera.front
. - [C-1-2] MUST have a resolution of at least VGA (640x480 pixels).
- [C-1-3] MUST NOT use a front-facing camera as the default for the Camera API and MUST NOT configure the API to treat a front-facing camera as the default rear-facing camera, even if it is the only camera on the device.
- [C-1-4] The camera preview MUST be mirrored horizontally relative to the orientation specified by the application when the current application has explicitly requested that the Camera display be rotated via a call to the
android.hardware.Camera.setDisplayOrientation()
method . Conversely, the preview MUST be mirrored along the device's default horizontal axis when the current application does not explicitly request that the Camera display be rotated via a call to theandroid.hardware.Camera.setDisplayOrientation()
method. - [C-1-5] MUST NOT mirror the final captured still image or video streams returned to application callbacks or committed to media storage.
- [C-1-6] MUST mirror the image displayed by the postview in the same manner as the camera preview image stream.
- MAY include features (such as auto-focus, flash, etc.) available to rear-facing cameras as described in section 7.5.1 .
If device implementations are capable of being rotated by user (such as automatically via an accelerometer or manually via user input):
- [C-2-1] The camera preview MUST be mirrored horizontally relative to the device's current orientation.
7.5.3. External Camera
Cihaz uygulamaları:
- MAY include support for an external camera that is not necessarily always connected.
If device implementations include support for an external camera, they:
- [C-1-1] MUST declare the platform feature flag
android.hardware.camera.external
andandroid.hardware camera.any
. - [C-1-2] MUST support USB Video Class (UVC 1.0 or higher) if the external camera connects through the USB host port.
- [C-1-3] MUST pass camera CTS tests with a physical external camera device connected. Details of camera CTS testing are available at source.android.com .
- SHOULD support video compressions such as MJPEG to enable transfer of high-quality unencoded streams (ie raw or independently compressed picture streams).
- MAY support multiple cameras.
- MAY support camera-based video encoding.
If camera-based video encoding is supported:
- [C-2-1] A simultaneous unencoded / MJPEG stream (QVGA or greater resolution) MUST be accessible to the device implementation.
7.5.4. Camera API Behavior
Android includes two API packages to access the camera, the newer android.hardware.camera2 API expose lower-level camera control to the app, including efficient zero-copy burst/streaming flows and per-frame controls of exposure, gain, white balance gains, color conversion, denoising, sharpening, and more.
The older API package, android.hardware.Camera
, is marked as deprecated in Android 5.0 but as it should still be available for apps to use. Android device implementations MUST ensure the continued support of the API as described in this section and in the Android SDK.
All features that are common between the deprecated android.hardware.Camera class and the newer android.hardware.camera2 package MUST have equivalent performance and quality in both APIs. For example, with equivalent settings, autofocus speed and accuracy must be identical, and the quality of captured images must be the same. Features that depend on the different semantics of the two APIs are not required to have matching speed or quality, but SHOULD match as closely as possible.
Device implementations MUST implement the following behaviors for the camera-related APIs, for all available cameras. Cihaz uygulamaları:
- [C-0-1] MUST use
android.hardware.PixelFormat.YCbCr_420_SP
for preview data provided to application callbacks when an application has never calledandroid.hardware.Camera.Parameters.setPreviewFormat(int)
. - [C-0-2] MUST further be in the NV21 encoding format when an application registers an
android.hardware.Camera.PreviewCallback
instance and the system calls theonPreviewFrame()
method and the preview format is YCbCr_420_SP, the data in the byte[] passed intoonPreviewFrame()
. That is, NV21 MUST be the default. - [C-0-3] MUST support the YV12 format (as denoted by the
android.graphics.ImageFormat.YV12
constant) for camera previews for both front- and rear-facing cameras forandroid.hardware.Camera
. (The hardware video encoder and camera may use any native pixel format, but the device implementation MUST support conversion to YV12.) - [C-0-4] MUST support the
android.hardware.ImageFormat.YUV_420_888
andandroid.hardware.ImageFormat.JPEG
formats as outputs through theandroid.media.ImageReader
API forandroid.hardware.camera2
devices that advertiseREQUEST_AVAILABLE_CAPABILITIES_BACKWARD_COMPATIBLE
capability inandroid.request.availableCapabilities
. - [C-0-5] MUST still implement the full Camera API included in the Android SDK documentation, regardless of whether the device includes hardware autofocus or other capabilities. For instance, cameras that lack autofocus MUST still call any registered
android.hardware.Camera.AutoFocusCallback
instances (even though this has no relevance to a non-autofocus camera.) Note that this does apply to front-facing cameras; for instance, even though most front-facing cameras do not support autofocus, the API callbacks must still be “faked” as described. - [C-0-6] MUST recognize and honor each parameter name defined as a constant in the
android.hardware.Camera.Parameters
class and theandroid.hardware.camera2.CaptureRequest
class. Conversely, device implementations MUST NOT honor or recognize string constants passed to theandroid.hardware.Camera.setParameters()
method other than those documented as constants on theandroid.hardware.Camera.Parameters
. That is, device implementations MUST support all standard Camera parameters if the hardware allows, and MUST NOT support custom Camera parameter types. For instance, device implementations that support image capture using high dynamic range (HDR) imaging techniques MUST support camera parameterCamera.SCENE_MODE_HDR
. - [C-0-7] MUST report the proper level of support with the
android.info.supportedHardwareLevel
property as described in the Android SDK and report the appropriate framework feature flags . - [C-0-8] MUST also declare its individual camera capabilities of
android.hardware.camera2
via theandroid.request.availableCapabilities
property and declare the appropriate feature flags ; MUST define the feature flag if any of its attached camera devices supports the feature. - [C-0-9] MUST broadcast the
Camera.ACTION_NEW_PICTURE
intent whenever a new picture is taken by the camera and the entry of the picture has been added to the media store. - [C-0-10] MUST broadcast the
Camera.ACTION_NEW_VIDEO
intent whenever a new video is recorded by the camera and the entry of the picture has been added to the media store. - [C-0-11] MUST have all cameras accessible via the deprecated
android.hardware.Camera
API also accessible via theandroid.hardware.camera2
API. - [C-0-12] MUST ensure that the facial appearance is NOT altered, including but not limited to altering facial geometry, facial skin tone, or facial skin smoothening for any
android.hardware.camera2
orandroid.hardware.Camera
API. - [C-SR-1] For devices with multiple RGB cameras facing in the same direction, are STRONGLY RECOMMENDED to support a logical camera device that lists capability
CameraMetadata.REQUEST_AVAILABLE_CAPABILITIES_LOGICAL_MULTI_CAMERA
, consisting of all of the RGB cameras facing that direction as physical sub-devices .
If device implementations provide a proprietary camera API to 3rd-party apps, they:
- [C-1-1] MUST implement such a camera API using
android.hardware.camera2
API. - MAY provide vendor tags and/or extensions to
android.hardware.camera2
API.
7.5.5. Camera Orientation
If device implementations have a front- or a rear-facing camera, such camera(s):
- [C-1-1] MUST be oriented so that the long dimension of the camera aligns with the screen's long dimension. That is, when the device is held in the landscape orientation, cameras MUST capture images in the landscape orientation. This applies regardless of the device's natural orientation; that is, it applies to landscape-primary devices as well as portrait-primary devices.
Devices that fulfill all of the following criteria are exempt from the requirement above:
- The device implements variable-geometry screens, such as foldable or hinged displays.
- When the device's fold or hinge state changes, the device switches between portrait-primary to landscape-primary (or vice-versa) orientations.
7.6. Memory and Storage
7.6.1. Minimum Memory and Storage
Cihaz uygulamaları:
- [C-0-1] MUST include a Download Manager that applications MAY use to download data files and they MUST be capable of downloading individual files of at least 100MB in size to the default “cache” location.
7.6.2. Application Shared Storage
Cihaz uygulamaları:
- [C-0-1] MUST offer storage to be shared by applications, also often referred as “shared external storage”, "application shared storage" or by the Linux path "/sdcard" it is mounted on.
- [C-0-2] MUST be configured with shared storage mounted by default, in other words “out of the box”, regardless of whether the storage is implemented on an internal storage component or a removable storage medium (eg Secure Digital card slot ).
- [C-0-3] MUST mount the application shared storage directly on the Linux path
sdcard
or include a Linux symbolic link fromsdcard
to the actual mount point. - [C-0-4] MUST enable scoped storage by default for all apps targeting API level 29 or above, except in the following situation:
- When the app has requested
android:requestLegacyExternalStorage="true"
in their manifest.
- When the app has requested
- [C-0-5] MUST redact location metadata, such as GPS Exif tags, stored in media files when those files are accessed through
MediaStore
, except when the calling app holds theACCESS_MEDIA_LOCATION
permission.
Device implementations MAY meet the above requirements using either of the following:
- User-accessible removable storage, such as a Secure Digital (SD) card slot.
- A portion of the internal (non-removable) storage as implemented in the Android Open Source Project (AOSP).
If device implementations use removable storage to satisfy the above requirements, they:
- [C-1-1] MUST implement a toast or pop-up user interface warning the user when there is no storage medium inserted in the slot.
- [C-1-2] MUST include a FAT-formatted storage medium (eg SD card) or show on the box and other material available at time of purchase that the storage medium has to be purchased separately.
If device implementations use a portion of the non-removable storage to satisfy the above requirements, they:
- SHOULD use the AOSP implementation of the internal application shared storage.
- MAY share the storage space with the application private data.
If device implementations have a USB port with USB peripheral mode support, they:
- [C-3-1] MUST provide a mechanism to access the data on the application shared storage from a host computer.
- SHOULD expose content from both storage paths transparently through Android's media scanner service and
android.provider.MediaStore
. - MAY use USB mass storage, but SHOULD use Media Transfer Protocol to satisfy this requirement.
If device implementations have a USB port with USB peripheral mode and support Media Transfer Protocol, they:
- SHOULD be compatible with the reference Android MTP host, Android File Transfer .
- SHOULD report a USB device class of 0x00.
- SHOULD report a USB interface name of 'MTP'.
7.6.3. Adoptable Storage
If the device is expected to be mobile in nature unlike Television, device implementations are:
- [C-SR-1] STRONGLY RECOMMENDED to implement the adoptable storage in a long-term stable location, since accidentally disconnecting them can cause data loss/corruption.
If the removable storage device port is in a long-term stable location, such as within the battery compartment or other protective cover, device implementations are:
- [C-SR-2] STRONGLY RECOMMENDED to implement adoptable storage .
7.7. USB
If device implementations have a USB port, they:
- SHOULD support USB peripheral mode and SHOULD support USB host mode.
- SHOULD support disabling data signaling over USB.
7.7.1. USB peripheral mode
If device implementations include a USB port supporting peripheral mode:
- [C-1-1] The port MUST be connectable to a USB host that has a standard type-A or type-C USB port.
- [C-1-2] MUST report the correct value of
iSerialNumber
in USB standard device descriptor throughandroid.os.Build.SERIAL
. - [C-1-3] MUST detect 1.5A and 3.0A chargers per the Type-C resistor standard and MUST detect changes in the advertisement if they support Type-C USB.
- [C-SR-1] The port SHOULD use micro-B, micro-AB or Type-C USB form factor. Existing and new Android devices are STRONGLY RECOMMENDED to meet these requirements so they will be able to upgrade to the future platform releases.
- [C-SR-2] The port SHOULD be located on the bottom of the device (according to natural orientation) or enable software screen rotation for all apps (including home screen), so that the display draws correctly when the device is oriented with the port at bottom. Existing and new Android devices are STRONGLY RECOMMENDED to meet these requirements so they will be able to upgrade to future platform releases.
- [C-SR-3] SHOULD implement support to draw 1.5 A current during HS chirp and traffic as specified in the USB Battery Charging specification, revision 1.2 . Existing and new Android devices are STRONGLY RECOMMENDED to meet these requirements so they will be able to upgrade to the future platform releases.
- [C-SR-4] STRONGLY RECOMMENDED to not support proprietary charging methods that modify Vbus voltage beyond default levels, or alter sink/source roles as such may result in interoperability issues with the chargers or devices that support the standard USB Power Delivery methods. While this is called out as "STRONGLY RECOMMENDED", in future Android versions we might REQUIRE all type-C devices to support full interoperability with standard type-C chargers.
- [C-SR-5] STRONGLY RECOMMENDED to support Power Delivery for data and power role swapping when they support Type-C USB and USB host mode.
- SHOULD support Power Delivery for high-voltage charging and support for Alternate Modes such as display out.
- SHOULD implement the Android Open Accessory (AOA) API and specification as documented in the Android SDK documentation.
If device implementations include a USB port and implement the AOA specification, they:
- [C-2-1] MUST declare support for the hardware feature
android.hardware.usb.accessory
. - [C-2-2] The USB mass storage class MUST include the string "android" at the end of the interface description
iInterface
string of the USB mass storage - SHOULD NOT implement AOAv2 audio documented in the Android Open Accessory Protocol 2.0 documentation. AOAv2 audio is deprecated as of Android version 8.0 (API level 26).
7.7.2. USB host mode
If device implementations include a USB port supporting host mode, they:
- [C-1-1] MUST implement the Android USB host API as documented in the Android SDK and MUST declare support for the hardware feature
android.hardware.usb.host
. - [C-1-2] MUST implement support to connect standard USB peripherals, in other words, they MUST either:
- Have an on-device type C port or ship with cable(s) adapting an on-device proprietary port to a standard USB type-C port (USB Type-C device).
- Have an on-device type A or ship with cable(s) adapting an on-device proprietary port to a standard USB type-A port.
- Have an on-device micro-AB port, which SHOULD ship with a cable adapting to a standard type-A port.
- [C-1-3] MUST NOT ship with an adapter converting from USB type A or micro-AB ports to a type-C port (receptacle).
- [C-SR-1] Are STRONGLY RECOMMENDED to implement the USB audio class as documented in the Android SDK documentation.
- SHOULD support charging the connected USB peripheral device while in host mode; advertising a source current of at least 1.5A as specified in the Termination Parameters section of the USB Type-C Cable and Connector Specification Revision 1.2 for USB Type-C connectors or using Charging Downstream Port(CDP) output current range as specified in the USB Battery Charging specifications, revision 1.2 for Micro-AB connectors.
- SHOULD implement and support USB Type-C standards.
If device implementations include a USB port supporting host mode and the USB audio class, they:
- [C-2-1] MUST support the USB HID class .
- [C-2-2] MUST support the detection and mapping of the following HID data fields specified in the USB HID Usage Tables and the Voice Command Usage Request to the
KeyEvent
constants as below:- Usage Page (0xC) Usage ID (0x0CD):
KEYCODE_MEDIA_PLAY_PAUSE
- Usage Page (0xC) Usage ID (0x0E9):
KEYCODE_VOLUME_UP
- Usage Page (0xC) Usage ID (0x0EA):
KEYCODE_VOLUME_DOWN
- Usage Page (0xC) Usage ID (0x0CF):
KEYCODE_VOICE_ASSIST
- Usage Page (0xC) Usage ID (0x0CD):
If device implementations include a USB port supporting host mode and the Storage Access Framework (SAF), they:
- [C-3-1] MUST recognize any remotely connected MTP (Media Transfer Protocol) devices and make their contents accessible through the
ACTION_GET_CONTENT
,ACTION_OPEN_DOCUMENT
, andACTION_CREATE_DOCUMENT
intents. .
If device implementations include a USB port supporting host mode and USB Type-C, they:
- [C-4-1] MUST implement Dual Role Port functionality as defined by the USB Type-C specification (section 4.5.1.3.3).
- [C-SR-2] STRONGLY RECOMMENDED to support DisplayPort, SHOULD support USB SuperSpeed Data Rates, and are STRONGLY RECOMMENDED to support Power Delivery for data and power role swapping.
- [C-SR-3] STRONGLY RECOMMENDED to NOT support Audio Adapter Accessory Mode as described in the Appendix A of the USB Type-C Cable and Connector Specification Revision 1.2 .
- SHOULD implement the Try.* model that is most appropriate for the device form factor. For example a handheld device SHOULD implement the Try.SNK model.
7.8. Ses
7.8.1. Mikrofon
If device implementations include a microphone, they:
- [C-1-1] MUST report the
android.hardware.microphone
feature constant. - [C-1-2] MUST meet the audio recording requirements in section 5.4 .
- [C-1-3] MUST meet the audio latency requirements in section 5.6 .
- [C-SR-1] Are STRONGLY RECOMMENDED to support near-ultrasound recording as described in section 7.8.3 .
If device implementations omit a microphone, they:
- [C-2-1] MUST NOT report the
android.hardware.microphone
feature constant. - [C-2-2] MUST implement the audio recording API at least as no-ops, per section 7 .
7.8.2. Ses çıkışı
If device implementations include a speaker or an audio/multimedia output port for an audio output peripheral such as a 4 conductor 3.5mm audio jack or USB host mode port using USB audio class , they:
- [C-1-1] MUST report the
android.hardware.audio.output
feature constant. - [C-1-2] MUST meet the audio playback requirements in section 5.5 .
- [C-1-3] MUST meet the audio latency requirements in section 5.6 .
- [C-SR-1] STRONGLY RECOMMENDED to support near-ultrasound playback as described in section 7.8.3 .
If device implementations do not include a speaker or audio output port, they:
- [C-2-1] MUST NOT report the
android.hardware.audio.output
feature. - [C-2-2] MUST implement the Audio Output related APIs as no-ops at least.
For the purposes of this section, an "output port" is a physical interface such as a 3.5mm audio jack, HDMI, or USB host mode port with USB audio class. Support for audio output over radio-based protocols such as Bluetooth, WiFi, or cellular network does not qualify as including an "output port".
7.8.2.1. Analog Audio Ports
In order to be compatible with the headsets and other audio accessories using the 3.5mm audio plug across the Android ecosystem, if device implementations include one or more analog audio ports, they:
- [C-SR-1] Are STRONGLY RECOMMENDED to include at least one of the audio port(s) to be a 4 conductor 3.5mm audio jack.
If device implementations have a 4 conductor 3.5mm audio jack, they:
- [C-1-1] MUST support audio playback to stereo headphones and stereo headsets with a microphone.
- [C-1-2] MUST support TRRS audio plugs with the CTIA pin-out order.
- [C-1-3] MUST support the detection and mapping to the keycodes for the following 3 ranges of equivalent impedance between the microphone and ground conductors on the audio plug:
- 70 ohm or less :
KEYCODE_HEADSETHOOK
- 210-290 ohm :
KEYCODE_VOLUME_UP
- 360-680 ohm :
KEYCODE_VOLUME_DOWN
- 70 ohm or less :
- [C-1-4] MUST trigger
ACTION_HEADSET_PLUG
upon a plug insert, but only after all contacts on plug are touching their relevant segments on the jack. - [C-1-5] MUST be capable of driving at least 150mV ± 10% of output voltage on a 32 ohm speaker impedance.
- [C-1-6] MUST have a microphone bias voltage between 1.8V ~ 2.9V.
- [C-1-7] MUST detect and map to the keycode for the following range of equivalent impedance between the microphone and ground conductors on the audio plug:
- 110-180 ohm:
KEYCODE_VOICE_ASSIST
- 110-180 ohm:
- [C-SR-2] Are STRONGLY RECOMMENDED to support audio plugs with the OMTP pin-out order.
- [C-SR-3] Are STRONGLY RECOMMENDED to support audio recording from stereo headsets with a microphone.
If device implementations have a 4 conductor 3.5mm audio jack and support a microphone, and broadcast the android.intent.action.HEADSET_PLUG
with the extra value microphone set as 1, they:
- [C-2-1] MUST support the detection of microphone on the plugged in audio accessory.
7.8.2.2. Digital Audio Ports
In order to be compatible with the headsets and other audio accessories using USB-C connectors and implementing (USB audio class) across the Android ecosystem as defined in Android USB headset specification .
See Section 2.2.1 for device-specific requirements.
7.8.3. Near-Ultrasound
Near-Ultrasound audio is the 18.5 kHz to 20 kHz band.
Cihaz uygulamaları:
- MUST correctly report the support of near-ultrasound audio capability via the AudioManager.getProperty API as follows:
If PROPERTY_SUPPORT_MIC_NEAR_ULTRASOUND
is "true", the following requirements MUST be met by the VOICE_RECOGNITION
and UNPROCESSED
audio sources:
- [C-1-1] The microphone's mean power response in the 18.5 kHz to 20 kHz band MUST be no more than 15 dB below the response at 2 kHz.
- [C-1-2] The microphone's unweighted signal to noise ratio over 18.5 kHz to 20 kHz for a 19 kHz tone at -26 dBFS MUST be no lower than 50 dB.
If PROPERTY_SUPPORT_SPEAKER_NEAR_ULTRASOUND
is "true":
- [C-2-1] The speaker's mean response in 18.5 kHz - 20 kHz MUST be no lower than 40 dB below the response at 2 kHz.
7.8.4. Sinyal bütünlüğü
Cihaz uygulamaları:
- SHOULD provide a glitch-free audio signal path for both input and output streams on handheld devices, as defined by zero glitches measured during a test of one minute per path. Test using OboeTester “Automated Glitch Test”.
The test requires an audio loopback dongle , used directly in a 3.5mm jack, and/or in combination with a USB-C to 3.5mm adapter. All audio output ports SHOULD be tested.
OboeTester currently supports AAudio paths, so the following combinations SHOULD be tested for glitches using AAudio:
Perf Mode | Paylaşma | Out Sample Rate | In Chans | Out Chans |
---|---|---|---|---|
DÜŞÜK GECİKME SÜRESİ | ÖZEL | BELİRTİLMEMİŞ | 1 | 2 |
DÜŞÜK GECİKME SÜRESİ | ÖZEL | BELİRTİLMEMİŞ | 2 | 1 |
DÜŞÜK GECİKME SÜRESİ | SHARED | BELİRTİLMEMİŞ | 1 | 2 |
DÜŞÜK GECİKME SÜRESİ | SHARED | BELİRTİLMEMİŞ | 2 | 1 |
HİÇBİRİ | SHARED | 48000 | 1 | 2 |
HİÇBİRİ | SHARED | 48000 | 2 | 1 |
HİÇBİRİ | SHARED | 44100 | 1 | 2 |
HİÇBİRİ | SHARED | 44100 | 2 | 1 |
HİÇBİRİ | SHARED | 16000 | 1 | 2 |
HİÇBİRİ | SHARED | 16000 | 2 | 1 |
A reliable stream SHOULD meet the following criteria for Signal to Noise Ratio (SNR) and Total Harmonic Distortion (THD) for 2000 Hz sine.
Transducer | THD | SNR |
---|---|---|
primary built-in speaker, measured using an external reference microphone | < 3.0% | >= 50 dB |
primary built-in microphone, measured using an external reference speaker | < 3.0% | >= 50 dB |
built-in analog 3.5 mm jacks, tested using loopback adapter | < 1% | >= 60 dB |
USB adapters supplied with the phone, tested using loopback adapter | < 1.0% | >= 60 dB |
7.9. Sanal gerçeklik
Android includes APIs and facilities to build "Virtual Reality" (VR) applications including high quality mobile VR experiences. Device implementations MUST properly implement these APIs and behaviors, as detailed in this section.
7.9.1. Virtual Reality Mode
Android includes support for VR Mode , a feature which handles stereoscopic rendering of notifications and disables monocular system UI components while a VR application has user focus.
7.9.2. Virtual Reality Mode - High Performance
If device implementations support VR mode, they:
- [C-1-1] MUST have at least 2 physical cores.
- [C-1-2] MUST declare the
android.hardware.vr.high_performance
feature. - [C-1-3] MUST support sustained performance mode.
- [C-1-4] MUST support OpenGL ES 3.2.
- [C-1-5] MUST support
android.hardware.vulkan.level
0. - SHOULD support
android.hardware.vulkan.level
1 or higher. - [C-1-6] MUST implement
EGL_KHR_mutable_render_buffer
,EGL_ANDROID_front_buffer_auto_refresh
,EGL_ANDROID_get_native_client_buffer
,EGL_KHR_fence_sync
,EGL_KHR_wait_sync
,EGL_IMG_context_priority
,EGL_EXT_protected_content
,EGL_EXT_image_gl_colorspace
, and expose the extensions in the list of available EGL extensions. - [C-1-8] MUST implement
GL_EXT_multisampled_render_to_texture2
,GL_OVR_multiview
,GL_OVR_multiview2
,GL_EXT_protected_textures
, and expose the extensions in the list of available GL extensions. - [C-SR-1] Are STRONGLY RECOMMENDED to implement
GL_EXT_external_buffer
,GL_EXT_EGL_image_array
,GL_OVR_multiview_multisampled_render_to_texture
, and expose the extensions in the list of available GL extensions. - [C-SR-2] Are STRONGLY RECOMMENDED to support Vulkan 1.1.
- [C-SR-3] Are STRONGLY RECOMMENDED to implement
VK_ANDROID_external_memory_android_hardware_buffer
,VK_GOOGLE_display_timing
,VK_KHR_shared_presentable_image
, and expose it in the list of available Vulkan extensions. - [C-SR-4] Are STRONGLY RECOMMENDED to expose at least one Vulkan queue family where
flags
contain bothVK_QUEUE_GRAPHICS_BIT
andVK_QUEUE_COMPUTE_BIT
, andqueueCount
is at least 2. - [C-1-7] The GPU and display MUST be able to synchronize access to the shared front buffer such that alternating-eye rendering of VR content at 60fps with two render contexts will be displayed with no visible tearing artifacts.
- [C-1-9] MUST implement support for
AHardwareBuffer
flagsAHARDWAREBUFFER_USAGE_GPU_DATA_BUFFER
,AHARDWAREBUFFER_USAGE_SENSOR_DIRECT_DATA
andAHARDWAREBUFFER_USAGE_PROTECTED_CONTENT
as described in the NDK. - [C-1-10] MUST implement support for
AHardwareBuffer
s with any combination of the usage flagsAHARDWAREBUFFER_USAGE_GPU_COLOR_OUTPUT
,AHARDWAREBUFFER_USAGE_GPU_SAMPLED_IMAGE
,AHARDWAREBUFFER_USAGE_PROTECTED_CONTENT
for at least the following formats:AHARDWAREBUFFER_FORMAT_R5G6B5_UNORM
,AHARDWAREBUFFER_FORMAT_R8G8B8A8_UNORM
,AHARDWAREBUFFER_FORMAT_R10G10B10A2_UNORM
,AHARDWAREBUFFER_FORMAT_R16G16B16A16_FLOAT
. - [C-SR-5] Are STRONGLY RECOMMENDED to support the allocation of
AHardwareBuffer
s with more than one layer and flags and formats specified in C-1-10. - [C-1-11] MUST support H.264 decoding at least 3840 x 2160 at 30fps, compressed to an average of 40Mbps (equivalent to 4 instances of 1920 x1080 at 30 fps-10 Mbps or 2 instances of 1920 x 1080 at 60 fps-20 Mbps).
- [C-1-12] MUST support HEVC and VP9, MUST be capable of decoding at least 1920 x 1080 at 30 fps compressed to an average of 10 Mbps and SHOULD be capable of decoding 3840 x 2160 at 30 fps-20 Mbps (equivalent to 4 instances of 1920 x 1080 at 30 fps-5 Mbps).
- [C-1-13] MUST support
HardwarePropertiesManager.getDeviceTemperatures
API and return accurate values for skin temperature. - [C-1-14] MUST have an embedded screen, and its resolution MUST be at least 1920 x 1080.
- [C-SR-6] Are STRONGLY RECOMMENDED to have a display resolution of at least 2560 x 1440.
- [C-1-15] The display MUST update at least 60 Hz while in VR Mode.
- [C-1-17] The display MUST support a low-persistence mode with ≤ 5 milliseconds persistence, persistence being defined as the amount of time for which a pixel is emitting light.
- [C-1-18] MUST support Bluetooth 4.2 and Bluetooth LE Data Length Extension section 7.4.3 .
- [C-1-19] MUST support and properly report Direct Channel Type for all of the following default sensor types:
-
TYPE_ACCELEROMETER
-
TYPE_ACCELEROMETER_UNCALIBRATED
-
TYPE_GYROSCOPE
-
TYPE_GYROSCOPE_UNCALIBRATED
-
TYPE_MAGNETIC_FIELD
-
TYPE_MAGNETIC_FIELD_UNCALIBRATED
-
- [C-SR-7] Are STRONGLY RECOMMENDED to support the
TYPE_HARDWARE_BUFFER
direct channel type for all Direct Channel Types listed above. - [C-1-21] MUST meet the gyroscope, accelerometer, and magnetometer related requirements for
android.hardware.hifi_sensors
, as specified in section 7.3.9 . - [C-SR-8] Are STRONGLY RECOMMENDED to support the
android.hardware.sensor.hifi_sensors
feature. - [C-1-22] MUST have end-to-end motion to photon latency not higher than 28 milliseconds.
- [C-SR-9] Are STRONGLY RECOMMENDED to have end-to-end motion to photon latency not higher than 20 milliseconds.
- [C-1-23] MUST have first-frame ratio, which is the ratio between the brightness of pixels on the first frame after a transition from black to white and the brightness of white pixels in steady state, of at least 85%.
- [C-SR-10] Are STRONGLY RECOMMENDED to have first-frame ratio of at least 90%.
- MAY provide an exclusive core to the foreground application and MAY support the
Process.getExclusiveCores
API to return the numbers of the cpu cores that are exclusive to the top foreground application.
If exclusive core is supported, then the core:
- [C-2-1] MUST not allow any other userspace processes to run on it (except device drivers used by the application), but MAY allow some kernel processes to run as necessary.
7.10. Haptics
See Section 2.2.1 for device-specific requirements.
7.11. Media Performance Class
The media performance class of the device implementation can be obtained from the android.os.Build.VERSION.MEDIA_PERFORMANCE_CLASS
. Requirements for media performance class are defined for each Android version starting with R (version 30). The special value of 0 designates that the device is not of a media performance class.
If device implementations return non-zero value for android.os.Build.VERSION.MEDIA_PERFORMANCE_CLASS
, they:
[C-1-1] MUST return at least a value of
android.os.Build.VERSION_CODES.R
.[C-1-2] MUST be a handheld device implementation.
[C-1-3] MUST meet all requirements for "Media Performance Class" described in section 2.2.7 .
See section 2.2.7 for device-specific requirements.
8. Performance and Power
Some minimum performance and power criteria are critical to the user experience and impact the baseline assumptions developers would have when developing an app.
8.1. User Experience Consistency
A smooth user interface can be provided to the end user if there are certain minimum requirements to ensure a consistent frame rate and response times for applications and games. Device implementations, depending on the device type, MAY have measurable requirements for the user interface latency and task switching as described in section 2 .
8.2. File I/O Access Performance
Providing a common baseline for a consistent file access performance on the application private data storage ( /data
partition) allows app developers to set a proper expectation that would help their software design. Device implementations, depending on the device type, MAY have certain requirements described in section 2 for the following read and write operations:
- Sequential write performance . Measured by writing a 256MB file using 10MB write buffer.
- Random write performance . Measured by writing a 256MB file using 4KB write buffer.
- Sequential read performance . Measured by reading a 256MB file using 10MB write buffer.
- Random read performance . Measured by reading a 256MB file using 4KB write buffer.
8.3. Power-Saving Modes
If device implementations include features to improve device power management that are included in AOSP (eg App Standby Bucket, Doze) or extend the features to apply stronger restrictions than the RESTRICTED App Standby Bucket , they:
- [C-1-1] MUST NOT deviate from the AOSP implementation for the triggering, maintenance, wakeup algorithms and the use of global system settings or DeviceConfig of App Standby and Doze power-saving modes.
- [C-1-2] MUST NOT deviate from the AOSP implementation for the use of global settings or DeviceConfig to manage the throttling of jobs, alarm and network for apps in each bucket for App standby.
- [C-1-3] MUST NOT deviate from the AOSP implementation for the number of the App Standby Buckets used for App Standby.
- [C-1-4] MUST implement App Standby Buckets and Doze as described in Power Management .
- [C-1-5] MUST return
true
forPowerManager.isPowerSaveMode()
when the device is on power save mode. - [C-1-6] MUST provide user affordance to display all apps that are exempted from App Standby and Doze power-saving modes or any battery optimizations and MUST implement the ACTION_REQUEST_IGNORE_BATTERY_OPTIMIZATIONS intent to ask the user to allow an app to ignore battery optimizations.
- [C-SR-1] Are STRONGLY RECOMMENDED to provide user affordance to enable and disable the battery saver feature.
- [C-SR-2] Are STRONGLY RECOMMENDED to provide user affordance to display all apps that are exempted from App Standby and Doze power-saving modes.
If device implementations extend power management features that are included in AOSP and that extension applies more stringent restrictions than the Rare App Standby Bucket , refer to section 3.5.1 .
In addition to the power-saving modes, Android device implementations MAY implement any or all of the 4 sleeping power states as defined by the Advanced Configuration and Power Interface (ACPI).
If device implementations implement S4 power states as defined by the ACPI, they:
- [C-1-1] MUST enter this state only after the user has taken an explicit action to put the device in an inactive state (eg by closing a lid that is physically part of the device or turning off a vehicle or television) and before the user re-activates the device (eg by opening the lid or turning the vehicle or television back on).
If device implementations implement S3 power states as defined by the ACPI, they:
[C-2-1] MUST meet C-1-1 above, or, MUST enter S3 state only when third-party applications do not need the system resources (eg the screen, CPU).
Conversely, MUST exit from S3 state when third-party applications need the system resources, as described on this SDK.
For example, while the third-party applications request to keep the screen on through
FLAG_KEEP_SCREEN_ON
or keep CPU running throughPARTIAL_WAKE_LOCK
, the device MUST NOT enter S3 state unless, as described in C-1-1, the user has taken explicit action to put the device in an inactive state. Conversely, at a time when a task that third-party apps implement through JobScheduler is triggered or Firebase Cloud Messaging is delivered to third-party apps, the device MUST exit the S3 state unless the user has put the device in an inactive state. These are not comprehensive examples and AOSP implements extensive wake-up signals that trigger a wakeup from this state.
8.4. Power Consumption Accounting
A more accurate accounting and reporting of the power consumption provides the app developer both the incentives and the tools to optimize the power usage pattern of the application.
Cihaz uygulamaları:
- [C-SR-1] STRONGLY RECOMMENDED to provide a per-component power profile that defines the current consumption value for each hardware component and the approximate battery drain caused by the components over time as documented in the Android Open Source Project site.
- [C-SR-2] STRONGLY RECOMMENDED to report all power consumption values in milliampere hours (mAh).
- [C-SR-3] STRONGLY RECOMMENDED to report CPU power consumption per each process's UID. Android Açık Kaynak Projesi, gereksinimi
uid_cputime
çekirdek modülü uygulaması aracılığıyla karşılar. - [C-SR-4] STRONGLY RECOMMENDED to make this power usage available via the
adb shell dumpsys batterystats
shell command to the app developer. - SHOULD be attributed to the hardware component itself if unable to attribute hardware component power usage to an application.
8.5. Consistent Performance
Performance can fluctuate dramatically for high-performance long-running apps, either because of the other apps running in the background or the CPU throttling due to temperature limits. Android includes programmatic interfaces so that when the device is capable, the top foreground application can request that the system optimize the allocation of the resources to address such fluctuations.
Cihaz uygulamaları:
[C-0-1] MUST report the support of Sustained Performance Mode accurately through the
PowerManager.isSustainedPerformanceModeSupported()
API method.SHOULD support Sustained Performance Mode.
If device implementations report support of Sustained Performance Mode, they:
- [C-1-1] MUST provide the top foreground application a consistent level of performance for at least 30 minutes, when the app requests it.
- [C-1-2] MUST honor the
Window.setSustainedPerformanceMode()
API and other related APIs.
If device implementations include two or more CPU cores, they:
- SHOULD provide at least one exclusive core that can be reserved by the top foreground application.
If device implementations support reserving one exclusive core for the top foreground application, they:
- [C-2-1] MUST report through the
Process.getExclusiveCores()
API method the ID numbers of the exclusive cores that can be reserved by the top foreground application. - [C-2-2] MUST not allow any user space processes except the device drivers used by the application to run on the exclusive cores, but MAY allow some kernel processes to run as necessary.
If device implementations do not support an exclusive core, they:
- [C-3-1] MUST return an empty list through the
Process.getExclusiveCores()
API method.
9. Security Model Compatibility
Cihaz uygulamaları:
[C-0-1] MUST implement a security model consistent with the Android platform security model as defined in Security and Permissions reference document in the APIs in the Android developer documentation.
[C-0-2] MUST support installation of self-signed applications without requiring any additional permissions/certificates from any third parties/authorities.
If device implementations declare the android.hardware.security.model.compatible
feature, they:
- [C-1-1] MUST support the requirements listed in the following subsections.
9.1. İzinler
Cihaz uygulamaları:
[C-0-1] MUST support the Android permissions model and the Android Roles Model as defined in the Android developer documentation. Specifically, they MUST enforce each permission and role defined as described in the SDK documentation; no permissions and no roles may be omitted, altered, or ignored.
MAY add additional permissions, provided the new permission ID strings are not in the
android.\*
namespace.[C-0-2] Permissions with a
protectionLevel
ofPROTECTION_FLAG_PRIVILEGED
MUST only be granted to apps preinstalled in the privileged path(s) of the system image and within the subset of the explicitly allowlisted permissions for each app. The AOSP implementation meets this requirement by reading and honoring the allowlisted permissions for each app from the files in theetc/permissions/
path and using thesystem/priv-app
path as the privileged path.
Permissions with a protection level of dangerous are runtime permissions. Applications with targetSdkVersion
> 22 request them at runtime.
Cihaz uygulamaları:
- [C-0-3] MUST show a dedicated interface for the user to decide whether to grant the requested runtime permissions and also provide an interface for the user to manage runtime permissions.
- [C-0-4] MUST have one and only one implementation of both user interfaces.
- [C-0-5] MUST NOT grant any runtime permissions to preinstalled apps unless:
- The user's consent can be obtained before the application uses it.
- The runtime permissions are associated with an intent pattern for which the preinstalled application is set as the default handler.
- [C-0-6] MUST grant the
android.permission.RECOVER_KEYSTORE
permission only to system apps that register a properly secured Recovery Agent. A properly secured Recovery Agent is defined as an on-device software agent that synchronizes with an off-device remote storage, that is equipped with secure hardware with protection equivalent or stronger than what is described in Google Cloud Key Vault Service to prevent brute-force attacks on the lockscreen knowledge factor.
Cihaz uygulamaları:
[C-0-7] MUST adhere to Android location permission properties when an app requests the location or physical activity data through standard Android API or proprietary mechanism. Such data includes but not limited to:
- Device's location (eg latitude and longitude) as described in section 9.8.8 .
- Information that can be used to determine or estimate the device's location (eg SSID, BSSID, Cell ID, or location of the network that the device is connected to).
- User's physical activity or classification of the physical activity.
More specifically, device implementations:
* [C-0-8] MUST obtain user consent to allow an app to access the
location or physical activity data.
* [C-0-9] MUST grant a runtime permission ONLY to the app that holds
sufficient permission as described on SDK.
For example,
TelephonyManager#getServiceState requires android.permission.ACCESS_FINE_LOCATION
).
The only exceptions to the Android location permission properties above are for apps not accessing Location to derive or identify user location; specifically:
- When apps hold the
RADIO_SCAN_WITHOUT_LOCATION
permission. - For device configuration and setup purposes, where system apps hold the
NETWORK_SETTINGS
orNETWORK_SETUP_WIZARD
permission.
Permissions can be marked as restricted altering their behavior.
[C-0-10] Permissions marked with the flag
hardRestricted
MUST NOT be granted to an app unless:- An app APK file is in the system partition.
- The user assigns a role that is associated with the
hardRestricted
permissions to an app. - The installer grants the
hardRestricted
to an app. - An app is granted the
hardRestricted
on an earlier Android version.
[C-0-11] Apps holding a
softRestricted
permission MUST get only limited access and MUST NOT gain full access until allowlisted as described in the SDK, where full and limited access is defined for eachsoftRestricted
permission (for example,READ_EXTERNAL_STORAGE
).[C-0-12] MUST NOT provide any custom functions or APIs to bypass the permission restrictions defined in setPermissionPolicy and setPermissionGrantState APIs.
[C-0-13] MUST use the AppOpsManager APIs to record and track each and every programmatic access of data protected by dangerous permissions from Android activities and services.
[C-0-14] MUST only assign roles to applications with functionalities that meet the role requirements.
[C-0-15] MUST not define roles that are duplicates or superset functionality of roles defined by the platform.
If devices report android.software.managed_users
, they:
- [C-1-1] MUST NOT have the following permissions silently granted by the admin:
- Location (ACCESS_BACKGROUND_LOCATION, ACCESS_COARSE_LOCATION, ACCESS_FINE_LOCATION).
- Camera (CAMERA)
- Microphone (RECORD_AUDIO)
- Body sensor (BODY_SENSORS)
- Physical activity (ACTIVITY_RECOGNITION)
If device implementations provide a user affordance to choose which apps can draw on top of other apps with an activity that handles the ACTION_MANAGE_OVERLAY_PERMISSION
intent, they:
- [C-2-1] MUST ensure that all activities with intent filters for the
ACTION_MANAGE_OVERLAY_PERMISSION
intent have the same UI screen, regardless of the initiating app or any information it provides.
If device implementations report android.software.device_admin, they:
- [C-3-1] MUST show a disclaimer during fully managed device setup (device owner setup) stating that the IT admin will have the ability to allow apps to control settings on the phone including microphone, camera and location, with options for user to continue setup or exit setup UNLESS the admin has opted out of control of permissions on the device.
If device implementations pre-install any packages that hold any of the System UI Intelligence , System Ambient Audio Intelligence , System Audio Intelligence , System Notification Intelligence , System Text Intelligence , or System Visual Intelligence roles, the packages:
- [C-4-1] MUST fulfill all requirements outlined for device implementations in section "9.8.6 Content Capture".
- [C-4-2] MUST NOT have android.permission.INTERNET permission. This is stricter than the STRONGLY RECOMMENDED listed in section 9.8.6.
- [C-4-3] MUST NOT bind to other apps, except for the following system apps: Bluetooth, Contacts, Media, Telephony, SystemUI, and components providing Internet APIs.This is stricter than the STRONGLY RECOMMENDED listed in section 9.8.6 .
9.2. UID and Process Isolation
Cihaz uygulamaları:
- [C-0-1] MUST support the Android application sandbox model, in which each application runs as a unique Unixstyle UID and in a separate process.
- [C-0-2] MUST support running multiple applications as the same Linux user ID, provided that the applications are properly signed and constructed, as defined in the Security and Permissions reference .
9.3. Filesystem Permissions
Cihaz uygulamaları:
- [C-0-1] MUST support the Android file access permissions model as defined in the Security and Permissions reference .
9.4. Alternate Execution Environments
Device implementations MUST keep consistency of the Android security and permission model, even if they include runtime environments that execute applications using some other software or technology than the Dalvik Executable Format or native code. Başka bir deyişle:
[C-0-1] Alternate runtimes MUST themselves be Android applications, and abide by the standard Android security model, as described elsewhere in section 9 .
[C-0-2] Alternate runtimes MUST NOT be granted access to resources protected by permissions not requested in the runtime's
AndroidManifest.xml
file via the <uses-permission
> mechanism.[C-0-3] Alternate runtimes MUST NOT permit applications to make use of features protected by Android permissions restricted to system applications.
[C-0-4] Alternate runtimes MUST abide by the Android sandbox model and installed applications using an alternate runtime MUST NOT reuse the sandbox of any other app installed on the device, except through the standard Android mechanisms of shared user ID and signing certificate .
[C-0-5] Alternate runtimes MUST NOT launch with, grant, or be granted access to the sandboxes corresponding to other Android applications.
[C-0-6] Alternate runtimes MUST NOT be launched with, be granted, or grant to other applications any privileges of the superuser (root), or of any other user ID.
[C-0-7] When the
.apk
files of alternate runtimes are included in the system image of device implementations, it MUST be signed with a key distinct from the key used to sign other applications included with the device implementations.[C-0-8] When installing applications, alternate runtimes MUST obtain user consent for the Android permissions used by the application.
[C-0-9] When an application needs to make use of a device resource for which there is a corresponding Android permission (such as Camera, GPS, etc.), the alternate runtime MUST inform the user that the application will be able to access that resource.
[C-0-10] When the runtime environment does not record application capabilities in this manner, the runtime environment MUST list all permissions held by the runtime itself when installing any application using that runtime.
Alternate runtimes SHOULD install apps via the
PackageManager
into separate Android sandboxes (Linux user IDs, etc.).Alternate runtimes MAY provide a single Android sandbox shared by all applications using the alternate runtime.
9.5. Multi-User Support
Android includes support for multiple users and provides support for full user isolation and clone user profiles with partial isolation(ie single additional user profile of type android.os.usertype.profile.CLONE
).
- Device implementations MAY but SHOULD NOT enable multi-user if they use removable media for primary external storage.
If device implementations include support for multiple users, they:
- [C-1-2] MUST, for each user, implement a security model consistent with the Android platform security model as defined in Security and Permissions reference document in the APIs.
- [C-1-3] MUST have separate and isolated shared application storage (aka
/sdcard
) directories for each user instance. - [C-1-4] MUST ensure that applications owned by and running on behalf a given user cannot list, read, or write to the files owned by any other user, even if the data of both users are stored on the same volume or dosya sistemi.
- [C-1-5] MUST encrypt the contents of the SD card when multiuser is enabled using a key stored only on non-removable media accessible only to the system if device implementations use removable media for the external storage APIs. As this will make the media unreadable by a host PC, device implementations will be required to switch to MTP or a similar system to provide host PCs with access to the current user's data.
If device implementations include support for multiple users, then for all users except users specifically created for running dual instances of the same app, they:
- [C-2-1] MUST have separate and isolated shared application storage (aka /sdcard) directories for each user instance.
- [C-2-2] MUST ensure that applications owned by and running on behalf of a given user cannot list, read, or write to the files owned by any other user, even if the data of both users are stored on the same volume or filesystem.
Device implementations MAY create a single additional user profile of type android.os.usertype.profile.CLONE
against the primary user (and only against the primary user) for the purpose of running dual instances of the same app. These dual instances share partially isolated storage, are presented to the end user in the launcher at the same time and appear in the same recents view. For example, this could be used to support the user installing two separate instances of a single app on a dual-SIM device.
If device implementations create the additional user profile discussed above, then they:
- [C-3-1] MUST only provide access to storage or data that is either already accessible to the parent user profile or is directly owned by this additional user profile.
- [C-3-2] MUST NOT have this as a work profile.
- [C-3-3] MUST have isolated private app data directories from the parent user account.
- [C-3-4] MUST NOT allow the additional user profile to be created if there is a Device Owner provisioned (see section 3.9.1) or allow a Device Owner to be provisioned without removing the additional user profile first.
9.6. Premium SMS Warning
Android includes support for warning users of any outgoing premium SMS message . Premium SMS messages are text messages sent to a service registered with a carrier that may incur a charge to the user.
Cihaz uygulamaları android.hardware.telephony
için destek beyan ederse:
- [C-1-1] MUST warn users before sending a SMS message to numbers identified by regular expressions defined in
/data/misc/sms/codes.xml
file in the device. The upstream Android Open Source Project provides an implementation that satisfies this requirement.
9.7. Güvenlik özellikleri
Device implementations MUST ensure compliance with security features in both the kernel and platform as described below.
The Android Sandbox includes features that use the Security-Enhanced Linux (SELinux) mandatory access control (MAC) system, seccomp sandboxing, and other security features in the Linux kernel. Cihaz uygulamaları:
- [C-0-1] MUST maintain compatibility with existing applications, even when SELinux or any other security features are implemented below the Android framework.
- [C-0-2] MUST NOT have a visible user interface when a security violation is detected and successfully blocked by the security feature implemented below the Android framework, but MAY have a visible user interface when an unblocked security violation occurs resulting in a successful faydalanmak.
- [C-0-3] MUST NOT make SELinux or any other security features implemented below the Android framework configurable to the user or app developer.
- [C-0-4] MUST NOT allow an application that can affect another application through an API (such as a Device Administration API) to configure a policy that breaks compatibility.
- [C-0-5] MUST split the media framework into multiple processes so that it is possible to more narrowly grant access for each process as described in the Android Open Source Project site.
- [C-0-6] MUST implement a kernel application sandboxing mechanism which allows filtering of system calls using a configurable policy from multithreaded programs. The upstream Android Open Source Project meets this requirement through enabling the seccomp-BPF with threadgroup synchronization (TSYNC) as described in the Kernel Configuration section of source.android.com .
Kernel integrity and self-protection features are integral to Android security. Cihaz uygulamaları:
- [C-0-7] MUST implement kernel stack buffer overflow protection mechanisms. Examples of such mechanisms are
CC_STACKPROTECTOR_REGULAR
andCONFIG_CC_STACKPROTECTOR_STRONG
. - [C-0-8] MUST implement strict kernel memory protections where executable code is read-only, read-only data is non-executable and non-writable, and writable data is non-executable (eg
CONFIG_DEBUG_RODATA
orCONFIG_STRICT_KERNEL_RWX
). - [C-0-9] MUST implement static and dynamic object size bounds checking of copies between user-space and kernel-space (eg
CONFIG_HARDENED_USERCOPY
) on devices originally shipping with API level 28 or higher. - [C-0-10] MUST NOT execute user-space memory when executing in the kernel mode (eg hardware PXN, or emulated via
CONFIG_CPU_SW_DOMAIN_PAN
orCONFIG_ARM64_SW_TTBR0_PAN
) on devices originally shipping with API level 28 or higher. - [C-0-11] MUST NOT read or write user-space memory in the kernel outside of normal usercopy access APIs (eg hardware PAN, or emulated via
CONFIG_CPU_SW_DOMAIN_PAN
orCONFIG_ARM64_SW_TTBR0_PAN
) on devices originally shipping with API level 28 or higher. - [C-0-12] MUST implement kernel page table isolation if the hardware is vulnerable to CVE-2017-5754 on all devices originally shipping with API level 28 or higher (eg
CONFIG_PAGE_TABLE_ISOLATION
orCONFIG_UNMAP_KERNEL_AT_EL0
). - [C-0-13] MUST implement branch prediction hardening if the hardware is vulnerable to CVE-2017-5715 on all devices originally shipping with API level 28 or higher (eg
CONFIG_HARDEN_BRANCH_PREDICTOR
). - [C-SR-1] STRONGLY RECOMMENDED to keep kernel data which is written only during initialization marked read-only after initialization (eg
__ro_after_init
). [C-SR-2] Are STRONGLY RECOMMENDED to randomize the layout of the kernel code and memory, and to avoid exposures that would compromise the randomization (eg
CONFIG_RANDOMIZE_BASE
with bootloader entropy via the/chosen/kaslr-seed Device Tree node
orEFI_RNG_PROTOCOL
) .[C-SR-3] Are STRONGLY RECOMMENDED to enable control flow integrity (CFI) in the kernel to provide additional protection against code-reuse attacks (eg
CONFIG_CFI_CLANG
andCONFIG_SHADOW_CALL_STACK
).[C-SR-4] Are STRONGLY RECOMMENDED not to disable Control-Flow Integrity (CFI), Shadow Call Stack (SCS) or Integer Overflow Sanitization (IntSan) on components that have it enabled.
[C-SR-5] Are STRONGLY RECOMMENDED to enable CFI, SCS, and IntSan for any additional security-sensitive userspace components as explained in CFI and IntSan .
[C-SR-6] Are STRONGLY RECOMMENDED to enable stack initialization in the kernel to prevent uses of uninitialized local variables (
CONFIG_INIT_STACK_ALL
orCONFIG_INIT_STACK_ALL_ZERO
). Also, device implementations SHOULD NOT assume the value used by the compiler to initialize the locals.[C-SR-7] Are STRONGLY RECOMMENDED to enable heap initialization in the kernel to prevent uses of uninitialized heap allocations (
CONFIG_INIT_ON_ALLOC_DEFAULT_ON
) and they SHOULD NOT assume the value used by the kernel to initialize those allocations.
If device implementations use a Linux kernel that is capable of supporting SELinux, they:
- [C-1-1] MUST implement SELinux.
- [C-1-2] MUST set SELinux to global enforcing mode.
- [C-1-3] MUST configure all domains in enforcing mode. No permissive mode domains are allowed, including domains specific to a device/vendor.
- [C-1-4] MUST NOT modify, omit, or replace the neverallow rules present within the system/sepolicy folder provided in the upstream Android Open Source Project (AOSP) and the policy MUST compile with all neverallow rules present, for both AOSP SELinux domains as well as device/vendor specific domains.
- [C-1-5] MUST run third-party applications targeting API level 28 or higher in per-application SELinux sandboxes with per-app SELinux restrictions on each application's private data directory.
- SHOULD retain the default SELinux policy provided in the system/sepolicy folder of the upstream Android Open Source Project and only further add to this policy for their own device-specific configuration.
If device implementations use kernel other than Linux or Linux without SELinux, they:
- [C-2-1] MUST use a mandatory access control system that is equivalent to SELinux.
If device implementations use I/O devices capable of DMA, they:
- [C-SR-8] Are STRONGLY RECOMMENDED to isolate each I/O device capable of DMA, using an IOMMU (egthe ARM SMMU).
Android contains multiple defense-in-depth features that are integral to device security. In addition, Android focuses on reducing key classes of common bugs that contribute to poor quality and security.
In order to reduce memory bugs, device implementations:
- [C-SR-9] Are STRONGLY RECOMMENDED to be tested using userspace memory error detection tools like MTE for ARMv9 devices, HWASan for ARMv8+ devices or ASan for other device types.
- [C-SR-10] Are STRONGLY RECOMMENDED to be tested using kernel memory error detection tools like KASAN (CONFIG_KASAN, CONFIG_KASAN_HW_TAGS for ARMv9 devices, CONFIG_KASAN_SW_TAGS for ARMv8 devices or CONFIG_KASAN_GENERIC for other device types).
- [C-SR-11] Are STRONGLY RECOMMENDED to be using memory error detection tools in production like MTE, GWP-ASan and KFENCE.
If device implementations use an Arm TrustZone-based TEE, they:
- [C-SR-12] Are STRONGLY RECOMMENDED to use a standard protocol for memory sharing, between Android and the TEE, like Arm Firmware Framework for Armv8-A (FF-A).
- [C-SR-13] Are STRONGLY RECOMMENDED to restrict trusted applications to only accessing memory which has been explicitly shared with them via the above protocol. If the device has support for the Arm S-EL2 exception level, this should be enforced by the secure partition manager. Otherwise, this should be enforced by the TEE OS.
9.8. Mahremiyet
9.8.1. Usage History
Android stores the history of the user's choices and manages such history by UsageStatsManager .
Cihaz uygulamaları:
- [C-0-1] MUST keep a reasonable retention period of such user history.
- [C-SR-1] Are STRONGLY RECOMMENDED to keep the 14 days retention period as configured by default in the AOSP implementation.
Android stores the system events using the StatsLog
identifiers, and manages such history via the StatsManager
and the IncidentManager
System API.
Cihaz uygulamaları:
- [C-0-2] MUST only include the fields marked with
DEST_AUTOMATIC
in the incident report created by the System API classIncidentManager
. - [C-0-3] MUST not use the system event identifiers to log any other event than what is described in the
StatsLog
SDK documents. If additional system events are logged, they MAY use a different atom identifier in the range between 100,000 and 200,000.
9.8.2. Kayıt
Cihaz uygulamaları:
- [C-0-1] MUST NOT preload or distribute software components out-of-box that send the user's private information (eg keystrokes, text displayed on the screen, bugreport) off the device without the user's consent or clear ongoing notifications.
- [C-0-2] MUST display and obtain explicit user consent that includes exactly the same message as AOSP whenever screen casting or screen recording is enabled via
MediaProjection
or proprietary APIs. MUST NOT provide users an affordance to disable future display of the user consent. - [C-0-3] MUST have an ongoing notification to the user while screen casting or screen recording is enabled. AOSP meets this requirement by showing an ongoing notification icon in the status bar.
If device implementations include functionality in the system that either captures the contents displayed on the screen and/or records the audio stream played on the device other than via the System API ContentCaptureService
, or other proprietary means described in Section 9.8.6 Content Capture , they :
- [C-1-1] MUST have an ongoing notification to the user whenever this functionality is enabled and actively capturing/recording.
If device implementations include a component enabled out-of-box, capable of recording ambient audio and/or record the audio played on the device to infer useful information about user's context, they:
- [C-2-1] MUST NOT store in persistent on-device storage or transmit off the device the recorded raw audio or any format that can be converted back into the original audio or a near facsimile, except with explicit user consent.
A “microphone indicator” refers to a view on screen, which is constantly visible to the user and cannot be obscured, which users understand as a microphone is in use(through unique text, color, icon, or some combination).
A “camera indicator” refers to a view on screen, which is constantly visible to the user and cannot be obscured, which users understand as a camera is in use (through unique text, color, icon, or some combination).
After the first one second displayed, an indicator can change visually, such as becoming smaller, and is not required to show as originally presented and understood.
The microphone indicator may be merged with an actively displayed camera indicator, provided that text, icons, or colors indicate to the user that microphone use has begun.
The camera indicator may be merged with an actively displayed microphone indicator, provided that text, icons, or colors indicate to the user that the camera use has begun.
If device implementations declare android.hardware.microphone
, they:
- [C-SR-1] Are STRONGLY RECOMMENDED to display microphone indicator when an app is accessing audio data from the microphone, but not when the microphone is only accessed by
HotwordDetectionService
,SOURCE_HOTWORD
,ContentCaptureService
, or app(s) holding the roles called out in Section 9.1 Permissions with CDD identifier [C-3-X]. . - [C-SR-2] Are STRONGLY RECOMMENDED to display the list of Recent and Active apps using microphone as returned from
PermissionManager.getIndicatorAppOpUsageData()
, along with any attribution messages associated with them. - [C-SR-3] Are STRONGLY RECOMMENDED to not hide the microphone indicator for system apps that have visible user interfaces or direct user interaction.
If device implementations declare android.hardware.camera.any
, they:
- [C-SR-4] Are STRONGLY RECOMMENDED to display camera indicator when an app is accessing live camera data, but not when the camera is only being accessed by app(s) holding the roles called out in Section 9.1 Permissions with CDD identifier [C-3-X].
- [C-SR-5] Are STRONGLY RECOMMENDED to display Recent and Active apps using camera as returned from
PermissionManager.getIndicatorAppOpUsageData()
, along with any attribution messages associated with them. - [C-SR-6] Are STRONGLY RECOMMENDED to not hide the camera indicator for system apps that have visible user interfaces or direct user interaction.
9.8.3. Bağlantı
If device implementations have a USB port with USB peripheral mode support, they:
- [C-1-1] MUST present a user interface asking for the user's consent before allowing access to the contents of the shared storage over the USB port.
9.8.4. Ağ trafiği
Cihaz uygulamaları:
- [C-0-1] MUST preinstall the same root certificates for the system-trusted Certificate Authority (CA) store as provided in the upstream Android Open Source Project.
- [C-0-2] MUST ship with an empty user root CA store.
- [C-0-3] MUST display a warning to the user indicating the network traffic may be monitored, when a user root CA is added.
If device traffic is routed through a VPN, device implementations:
- [C-1-1] MUST display a warning to the user indicating either:
- That network traffic may be monitored.
- That network traffic is being routed through the specific VPN application providing the VPN.
If device implementations have a mechanism, enabled out-of-box by default, that routes network data traffic through a proxy server or VPN gateway (for example, preloading a VPN service with android.permission.CONTROL_VPN
granted), they:
- [C-2-1] MUST ask for the user's consent before enabling that mechanism, unless that VPN is enabled by the Device Policy Controller via the
DevicePolicyManager.setAlwaysOnVpnPackage()
, in which case the user does not need to provide a separate consent, but MUST only be notified.
If device implementations implement a user affordance to toggle on the "always-on VPN" function of a 3rd-party VPN app, they:
- [C-3-1] MUST disable this user affordance for apps that do not support always-on VPN service in the
AndroidManifest.xml
file via setting theSERVICE_META_DATA_SUPPORTS_ALWAYS_ON
attribute tofalse
.
9.8.5. Device Identifiers
Cihaz uygulamaları:
- [C-0-1] MUST prevent access to the device serial number and, where applicable, IMEI/MEID, SIM serial number, and International Mobile Subscriber Identity (IMSI) from an app, unless it meets one of the following requirements:
- is a signed carrier app that is verified by device manufacturers.
- has been granted the
READ_PRIVILEGED_PHONE_STATE
permission. - has carrier privileges as defined in UICC Carrier Privileges .
- is a device owner or profile owner that has been granted the
READ_PHONE_STATE
permission. - (For SIM serial number/ICCID only) has the local regulations requirement that the app detect changes in the subscriber's identity.
9.8.6. Content Capture and App Search
Android, through the System API ContentCaptureService
, AugmentedAutofillService
, AppSearchGlobalManager.query
, or by other proprietary means, supports a mechanism for device implementations to capture the following application data interactions between the applications and the user:
- Text and graphics rendered on-screen, including but not limited to, notifications and assist data via
AssistStructure
API. - Media data, such as audio or video, recorded or played by the device.
- Input events (eg key, mouse, gesture, voice, video, and accessibility).
- Any other events that an application provides to the system via the
Content Capture
API or orAppSearchManager
API a similarly capable Android and proprietary API. - Any text or other data sent via the
TextClassifier API
to the System TextClassifier ie to the system service to understand the meaning of text, as well as generating predicted next actions based on the text. - Data indexed by the platform AppSearch implementation, including but not limited to text, graphics, media data or other similar data.
If device implementations capture the data above, they:
- [C-0-1] MUST encrypt all such data when stored in the device. This encryption MAY be carried out using Android File Based Encryption, or any of the ciphers listed as API version 26+ described in Cipher SDK .
- [C-0-2] MUST NOT back up either raw or encrypted data using Android backup methods or any other back up methods.
- [C-0-3] MUST only send all such data and the log of the device using a privacy-preserving mechanism. The privacy-preserving mechanism is defined as “those which allow only analysis in aggregate and prevent matching of logged events or derived outcomes to individual users”, to prevent any per-user data being introspectable (eg, implemented using a differential privacy technology such as
RAPPOR
). - [C-0-4] MUST NOT associate such data with any user identity (such as
Account
) on the device, except with explicit user consent each time the data is associated. - [C-0-5] MUST NOT share such data with other OS components that don't follow requirements outlined in the current section (9.8.6 Content Capture), except with explicit user consent every time it is shared.
- [C-0-6] MUST provide user affordance to erase such data that the
ContentCaptureService
or the proprietary means collects if the data is stored in any form on the device. - [C-0-7] MUST provide a user affordance to opt-out of the data, collected via AppSearch or proprietary means from being shown in android platform eg launcher.
- [C-SR-1] Are STRONGLY RECOMMENDED NOT to request the INTERNET permission.
- [C-SR-2] Are STRONGLY RECOMMENDED to only access the internet through structured APIs backed by publicly available open-source implementations.
If device implementations include a service that implements the System API ContentCaptureService
, AppSearchManager.index
, or any proprietary service that captures the data as described as above, they:
- [C-1-1] MUST NOT allow users to replace the services with a user-installable application or service and MUST only allow the preinstalled services to capture such data.
- [C-1-2] MUST NOT allow any apps other than the preinstalled services mechanism to be able to capture such data.
- [C-1-3] MUST provide user affordance to disable the services.
- [C-1-4] MUST NOT omit user affordance to manage Android permissions that are held by the services and follow Android permissions model as described in Section 9.1. İzin .
[C-SR-3] Are STRONGLY RECOMMENDED to keep the services separate from other system components(eg not binding the service or sharing process IDs) except for the following:
- Telephony, Contacts, System UI, and Media
Android, through SpeechRecognizer#onDeviceSpeechRecognizer()
provides ability to perform speech recognition on the device, without involving the network. Any implementation of on-device SpeechRecognizer MUST follow the policies outlined in this section.
9.8.7. Clipboard Access
Cihaz uygulamaları:
- [C-0-1] MUST NOT return a clipped data on the clipboard (eg via the
ClipboardManager
API) unless the app is the default IME or is the app that currently has focus.
9.8.8. Konum
Location includes information in the Android Location class( such as Latitude, Longitude, Altitude), as well as identifiers that can be converted to Location. Location can be as fine as DGPS (Differential Global Positioning System) or as coarse as country level locations (like the country code location - MCC - Mobile Country Code).
The following is a list of location types that either directly derive a user's location or can be converted to a user's location. This is not a comprehensive list, but should be used as an example on what Location can directly or indirectly be derived from:
- GPS/GNSS/DGPS/PPP
- Global Positioning Solution or Global Navigation Satellite System or Differential Global Positioning Solution
- This also includes Raw GNSS Measurements and GNSS Status
- Fine Location can be derived from the Raw GNSS Measurements
- Wireless Technologies with unique identifiers such as:
- WiFi access points (MAC, BSSID, Name, or SSID)
- Bluetooth/BLE (MAC, BSSID, Name, or SSID)
- UWB (MAC, BSSID, Name, or SSID)
- Cell Tower ID (3G, 4G, 5G… Iincluding all future Cellular Modem technologies that have unique identifiers)
As a primary point of reference, see the Android APIs which require ACCESS_FINE_Location or ACCESS_COARSE_Location permissions.
Cihaz uygulamaları:
- [C-0-1] MUST NOT turn on/off device location setting and Wi-Fi/Bluetooth scanning settings without explicit user consent or user initiation.
- [C-0-2] MUST provide the user affordance to access location related information including recent location requests, app level permissions and usage of Wi-Fi/Bluetooth scanning for determining location.
- [C-0-3] MUST ensure that the application using Emergency Location Bypass API [LocationRequest.setLocationSettingsIgnored()] is a user initiated emergency session (eg dial 911 or text to 911). For Automotive however, a vehicle MAY initiate an emergency session without active user interaction in the case a crash/accident is detected (eg to satisfy eCall requirements).
- [C-0-4] MUST preserve the Emergency Location Bypass API's ability to bypass device location settings without changing the settings.
- [C-0-5] MUST schedule a notification that reminds the user after an app in the background has accessed their location using the [
ACCESS_BACKGROUND_LOCATION
] permission.
9.8.9. Yüklü uygulamalar
Android apps targeting API level 30 or above cannot see details about other installed apps by default (see Package visibility in the Android SDK documentation).
Cihaz uygulamaları:
- [C-0-1] MUST NOT expose to any app targeting API level 30 or above details about any other installed app, unless the app is already able to see details about the other installed app through the managed APIs. This includes but is not limited to details exposed by any custom APIs added by the device implementer, or accessible via the filesystem.
- [C-0-2] MUST NOT give to any app, read or write access to files in any other app's dedicated, app-specific directory within external storage. The only exceptions are as follows:
- The external storage provider authority (eg apps like DocumentsUI).
- Download Provider which uses the “downloads” provider authority for downloading files to app storage.
- Platform-signed media transfer protocol (MTP) apps which use the privileged permission ACCESS_MTP to enable transferring files to another device.
- Apps which install other apps and have the permission INSTALL_PACKAGES can access only “obb” directories for the purpose of managing APK expansion files .
9.8.10. Connectivity Bug Report
If device implementations declare the android.hardware.telephony
feature flag, they:
- [C-1-1] MUST support generating connectivity bug reports via
BUGREPORT_MODE_TELEPHONY
with BugreportManager. - [C-1-2] MUST obtain user consent every time
BUGREPORT_MODE_TELEPHONY
is used to generate a report and MUST NOT prompt the user to consent to all future requests from the application. - [C-1-3] MUST NOT return the generated report to the requesting app without explicit user consent.
- [C-1-4] Reports generated using
BUGREPORT_MODE_TELEPHONY
MUST contain at least the following information:-
TelephonyDebugService
dump -
TelephonyRegistry
dump -
WifiService
dump -
ConnectivityService
dump - A dump of the calling package's
CarrierService
instance (if bound) - Radio log buffer
-
- [C-1-5] MUST NOT include the following in the generated reports:
- Any kind of information that isn't directly related to connectivity debugging.
- Any kind of user-installed application traffic logs or detailed profiles of user-installed applications/packages (UIDs are okay, package names are not).
- MAY include additional information that is not associated with any user identity. (eg vendor logs).
If device implementations include additional information (eg vendor logs) in bug reports and that information has privacy/security/battery/storage/memory impact, they:
- [C-SR-1] Are STRONGLY RECOMMENDED to have a developer setting defaulted to disabled. The AOSP reference implementation meets this by providing the
Enable verbose vendor logging
option in developer settings to include additional device-specific vendor logs in the bug reports.
9.8.11. Data blobs sharing
Android, through BlobStoreManager allows apps to contribute data blobs to the System to be shared with a selected set of apps.
If device implementations support shared data blobs as described in the SDK documentation , they:
- [C-1-1] MUST NOT share data blobs belonging to apps beyond what they intended to allow (ie the scope of default access and the other access modes that can be specified using BlobStoreManager.session#allowPackageAccess() , BlobStoreManager.session#allowSameSignatureAccess() , or BlobStoreManager.session#allowPublicAccess() MUST NOT be modified). The AOSP reference implementation meets these requirements.
- [C-1-2] MUST NOT send off device or share with other apps the secure hashes of data blobs (which are used to control access).
9.8.12. Music Recognition
Android, through the System API MusicRecognitionManager, supports a mechanism for device implementations to request music recognition, given an audio record, and delegate the music recognition to a privileged app implementing the MusicRecognitionService API.
If device implementations include a service that implements the System API MusicRecognitionManager or any proprietary service that streams audio data as described as above, they:
- [C-1-1] MUST enforce that the caller of MusicRecognitionManager holds the
MANAGE_MUSIC_RECOGNITION
permission - [C-1-2] MUST enforce that a single, pre-installed, music recognition application implements MusicRecognitionService.
- [C-1-3] MUST NOT allow users to replace the MusicRecognitionManagerService or MusicRecognitionService with a user-installable application or service.
- [C-1-4] MUST ensure that when MusicRecognitionManagerService accesses the audio record and forwards it to the application implementing the MusicRecognitionService, the audio access is tracked via invocations of AppOpsManager.noteOp / startOp .
If device implementations of MusicRecognitionManagerService or MusicRecognitionService store any audio data captured, they:
- [C-2-1] MUST NOT store any raw audio or audio fingerprints on disk at all, or in memory for longer than 14 days.
- [C-2-2] MUST NOT share such data beyond the MusicRecognitionService, except with explicit user consent every time it is shared.
9.8.13. SensorPrivacyManager
If device implementations provide the user a software affordance to turn off the camera and/or microphone input for the device implementation, they:
- [C-1-1] MUST accurately return 'true' for the relevant supportsSensorToggle() API method.
- [C-1-2] MUST, when an app tries to access a blocked microphone or camera, present the user with a non-dismissable user affordance that clearly indicates that the sensor is blocked and requires a choice to continue blocking or unblock as per the AOSP implementation which meets this requirement.
- [C-1-3] MUST only pass blank (or fake) camera and audio data to apps and not report an error code due to the user not turning on the camera nor microphone via the user affordance presented per [C-1-2 ] üstünde.
9.9. Data Storage Encryption
All devices MUST meet the requirements of section 9.9.1. Devices which launched on an API level earlier than that of this document are exempted from the requirements of sections 9.9.2 and 9.9.3; instead they MUST meet the requirements in section 9.9 of the Android Compatibility Definition document corresponding to the API level on which the device launched.
9.9.1. Direct Boot
Cihaz uygulamaları:
[C-0-1] MUST implement the Direct Boot mode APIs even if they do not support Storage Encryption.
[C-0-2] The
ACTION_LOCKED_BOOT_COMPLETED
andACTION_USER_UNLOCKED
Intents MUST still be broadcast to signal Direct Boot aware applications that Device Encrypted (DE) and Credential Encrypted (CE) storage locations are available for user.
9.9.2. Encryption requirements
Cihaz uygulamaları:
- [C-0-1] MUST encrypt the application private data (
/data
partition), as well as the application shared storage partition (/sdcard
partition) if it is a permanent, non-removable part of the device. - [C-0-2] MUST enable the data storage encryption by default at the time the user has completed the out-of-box setup experience.
[C-0-3] MUST meet the above data storage encryption requirement by implementing one of the following two encryption methods:
- File Based Encryption (FBE) and Metadata Encryption as described in section 9.9.3.1.
- Per-User Block-Level Encryption as described in section 9.9.3.2.
9.9.3. Encryption Methods
If device implementations are encrypted, they:
- [C-1-1] MUST boot up without challenging the user for credentials and allow Direct Boot aware apps to access to the Device Encrypted (DE) storage after the
ACTION_LOCKED_BOOT_COMPLETED
message is broadcasted. - [C-1-2] MUST only allow access to Credential Encrypted (CE) storage after the user has unlocked the device by supplying their credentials (eg. passcode, pin, pattern or fingerprint) and the
ACTION_USER_UNLOCKED
message is broadcasted. - [C-1-13] MUST NOT offer any method to unlock the CE protected storage without either the user-supplied credentials, a registered escrow key or a resume on reboot implementation meeting the requirements in section 9.9.4 .
- [C-1-4] MUST use Verified Boot.
9.9.3.1. File Based Encryption with Metadata Encryption
If device implementations use File Based Encryption with Metadata Encryption, they:
- [C-1-5] MUST encrypt file contents and filesystem metadata using AES-256-XTS or Adiantum. AES-256-XTS refers to the Advanced Encryption Standard with a 256-bit cipher key length, operated in XTS mode; the full length of the key is 512 bits. Adiantum refers to Adiantum-XChaCha12-AES, as specified at https://github.com/google/adiantum. Filesystem metadata is data such as file sizes, ownership, modes, and extended attributes (xattrs).
- [C-1-6] MUST encrypt file names using AES-256-CBC-CTS or Adiantum.
- [C-1-12] If the device has Advanced Encryption Standard (AES) instructions (such as ARMv8 Cryptography Extensions on ARM-based devices, or AES-NI on x86-based devices) then the AES-based options above for file name, file contents, and filesystem metadata encryption MUST be used, not Adiantum.
- [C-1-13] MUST use a cryptographically strong and non-reversible key derivation function (eg HKDF-SHA512) to derive any needed subkeys (eg per-file keys) from the CE and DE keys. "Cryptographically strong and non-reversible" means that the key derivation function has a security strength of at least 256 bits and behaves as a pseudorandom function family over its inputs.
- [C-1-14] MUST NOT use the same File Based Encryption (FBE) keys or subkeys for different cryptographic purposes (eg for both encryption and key derivation, or for two different encryption algorithms).
- [C-1-15] MUST ensure that all non-deleted blocks of encrypted file contents on persistent storage were encrypted using combinations of encryption key and initialization vector (IV) that depend on both the file and the offset within the file. In addition, all such combinations MUST be distinct, except where the encryption is done using inline encryption hardware that only supports an IV length of 32 bits.
- [C-1-16] MUST ensure that all non-deleted encrypted filenames on persistent storage in distinct directories were encrypted using distinct combinations of encryption key and initialization vector (IV).
[C-1-17] MUST ensure that all encrypted filesystem metadata blocks on persistent storage were encrypted using distinct combinations of encryption key and initialization vector (IV).
Keys protecting CE and DE storage areas and filesystem metadata:
- [C-1-7] MUST be cryptographically bound to a hardware-backed Keystore. This keystore MUST be bound to Verified Boot and the device's hardware root of trust.
- [C-1-8] CE keys MUST be bound to a user's lock screen credentials.
- [C-1-9] CE keys MUST be bound to a default passcode when the user has not specified lock screen credentials.
- [C-1-10] MUST be unique and distinct, in other words no user's CE or DE key matches any other user's CE or DE keys.
- [C-1-11] MUST use the mandatorily supported ciphers, key lengths and modes.
- [C-1-12] MUST be securely erased during bootloader unlock and lock as described here .
SHOULD make preinstalled essential apps (eg Alarm, Phone, Messenger) Direct Boot aware.
The upstream Android Open Source project provides a preferred implementation of File Based Encryption based on the Linux kernel "fscrypt" encryption feature, and of Metadata Encryption based on the Linux kernel "dm-default-key" feature.
9.9.3.2. Per-User Block-Level Encryption
If device implementations use per-user block-level encryption, they:
- [C-1-1] MUST enable multi-user support as described in section 9.5.
- [C-1-2] MUST provide per-user partitions, either using raw partitions or logical volumes.
- [C-1-3] MUST use unique and distinct encryption keys per-user for encryption of the underlying block devices.
[C-1-4] MUST use AES-256-XTS for block-level encryption of the user partitions.
The keys protecting the per-user block-level encrypted devices:
- [C-1-5] MUST be cryptographically bound to a hardware-backed Keystore. This keystore MUST be bound to Verified Boot and the device's hardware root of trust.
- [C-1-6] MUST be bound to the corresponding user's lock screen credentials.
Per-user block-level encryption can be implemented using the Linux kernel "dm-crypt" feature over per-user partitions.
9.9.4. Resume on Reboot
Resume on Reboot allows unlocking the CE storage of all apps, including those that do not yet support Direct Boot, after a reboot initiated by an OTA. This feature enables users to receive notifications from installed apps after the reboot.
An implementation of Resume-on-Reboot must continue to ensure that when a device falls into an attacker's hands, it is extremely difficult for that attacker to recover the user's CE-encrypted data, even if the device is powered on, CE storage is unlocked, and the user has unlocked the device after receiving an OTA. For insider attack resistance, we also assume the attacker gains access to broadcast cryptographic signing keys.
Özellikle:
[C-0-1] CE storage MUST NOT be readable even for the attacker who physically has the device and then has these capabilities and limitations:
- Can use the signing key of any vendor or company to sign arbitrary messages.
- Can cause an OTA to be received by the device.
- Can modify the operation of any hardware (AP, flash etc) except as detailed below, but such modification involves a delay of at least an hour and a power cycle that destroys RAM contents.
- Cannot modify the operation of tamper-resistant hardware (eg Titan M).
- Cannot read the RAM of the live device.
- Cannot obtain the user's credential (PIN, pattern, password) or otherwise cause it to be entered.
By way of example, a device implementation that implements and complies with all of the descriptions found here will be compliant with [C-0-1].
9.10. Device Integrity
The following requirements ensure there is transparency to the status of the device integrity. Cihaz uygulamaları:
[C-0-1] MUST correctly report through the System API method
PersistentDataBlockManager.getFlashLockState()
whether their bootloader state permits flashing of the system image.[C-0-2] MUST support Verified Boot for device integrity.
If device implementations are already launched without supporting Verified Boot on an earlier version of Android and can not add support for this feature with a system software update, they MAY be exempted from the requirement.
Verified Boot is a feature that guarantees the integrity of the device software. If device implementations support the feature, they:
- [C-1-1] MUST declare the platform feature flag
android.software.verified_boot
. - [C-1-2] MUST perform verification on every boot sequence.
- [C-1-3] MUST start verification from an immutable hardware key that is the root of trust and go all the way up to the system partition.
- [C-1-4] MUST implement each stage of verification to check the integrity and authenticity of all the bytes in the next stage before executing the code in the next stage.
- [C-1-5] MUST use verification algorithms as strong as current recommendations from NIST for hashing algorithms (SHA-256) and public key sizes (RSA-2048).
- [C-1-6] MUST NOT allow boot to complete when system verification fails, unless the user consents to attempt booting anyway, in which case the data from any non-verified storage blocks MUST not be used.
- [C-1-7] MUST NOT allow verified partitions on the device to be modified unless the user has explicitly unlocked the bootloader.
- [C-SR-1] If there are multiple discrete chips in the device (eg radio, specialized image processor), the boot process of each of those chips is STRONGLY RECOMMENDED to verify every stage upon booting.
- [C-1-8] MUST use tamper-evident storage: for storing whether the bootloader is unlocked. Tamper-evident storage means that the bootloader can detect if the storage has been tampered with from inside Android.
- [C-1-9] MUST prompt the user, while using the device, and require physical confirmation before allowing a transition from bootloader locked mode to bootloader unlocked mode.
- [C-1-10] MUST implement rollback protection for partitions used by Android (eg boot, system partitions) and use tamper-evident storage for storing the metadata used for determining the minimum allowable OS version.
- [C-1-11] MUST securely erase all user data during bootloader unlock and lock, as per '9.12. Data Deletion' (including the userdata partition and any NVRAM spaces).
- [C-SR-2] Are STRONGLY RECOMMENDED to verify all privileged app APK files with a chain of trust rooted in partitions protected by Verified Boot.
- [C-SR-3] Are STRONGLY RECOMMENDED to verify any executable artifacts loaded by a privileged app from outside its APK file (such as dynamically loaded code or compiled code) before executing them or STRONGLY RECOMMENDED not to execute them at all.
- SHOULD implement rollback protection for any component with persistent firmware (eg modem, camera) and SHOULD use tamper-evident storage for storing the metadata used for determining the minimum allowable version.
If device implementations are already launched without supporting C-1-8 through C-1-11 on an earlier version of Android and can not add support for these requirements with a system software update, they MAY be exempted from the requirements.
The upstream Android Open Source Project provides a preferred implementation of this feature in the external/avb/
repository, which can be integrated into the bootloader used for loading Android.
Cihaz uygulamaları:
- [C-0-3] MUST support cryptographically verifying file content against a trusted key without reading the whole file.
- [C-0-4] MUST NOT allow the read requests on a protected file to succeed when the read content do not verify against a trusted key.
If device implementations are already launched without the ability to verify file content against a trusted key on an earlier Android version and can not add support for this feature with a system software update, they MAY be exempted from the requirement. The upstream Android Open Source project provides a preferred implementation of this feature based on the Linux kernel fs-verity feature.
Cihaz uygulamaları:
- [C-SR-4] Are STRONGLY RECOMMENDED to support the Android Protected Confirmation API .
If device implementations support the Android Protected Confirmation API they:
[C-3-1] MUST report
true
for theConfirmationPrompt.isSupported()
API.[C-3-2] MUST ensure that code running in the Android OS including its kernel, malicious or otherwise, cannot generate a positive response without user interaction.
[C-3-3] MUST ensure that the user has been able to review and approve the prompted message even in the event that the Android OS, including its kernel, is compromised.
9.11. Keys and Credentials
The Android Keystore System allows app developers to store cryptographic keys in a container and use them in cryptographic operations through the KeyChain API or the Keystore API . Cihaz uygulamaları:
- [C-0-1] MUST allow at least 8,192 keys to be imported or generated.
- [C-0-2] The lock screen authentication MUST implement a time interval between failed attempts. With n as the failed attempt count, the time interval MUST be at least 30 seconds for 9 < n < 30. For n > 29, the time interval value MUST be at least 30*2^floor((n-30)/10)) seconds or at least 24 hours, whichever is smaller.
- SHOULD not limit the number of keys that can be generated
When the device implementation supports a secure lock screen, it:
- [C-1-1] MUST back up the keystore implementation with an isolated execution environment.
- [C-1-2] MUST have implementations of RSA, AES, ECDSA and HMAC cryptographic algorithms and MD5, SHA1, and SHA-2 family hash functions to properly support the Android Keystore system's supported algorithms in an area that is securely isolated from the code running on the kernel and above. Güvenli izolasyon, çekirdek veya kullanıcı alanı kodunun, DMA dahil, izole edilmiş ortamın dahili durumuna erişebileceği tüm potansiyel mekanizmaları ENGELLEMELİDİR. Yukarı akışlı Android Açık Kaynak Projesi (AOSP), Trusty uygulamasını kullanarak bu gereksinimi karşılar, ancak başka bir ARM TrustZone tabanlı çözüm veya uygun bir hipervizör tabanlı izolasyonun üçüncü taraflarca gözden geçirilmiş güvenli uygulaması alternatif seçeneklerdir.
- [C-1-3] MUST perform the lock screen authentication in the isolated execution environment and allow the authentication-bound keys to be used only after successful authentication. Kilit ekranı kimlik bilgileri, yalnızca yalıtılmış yürütme ortamının kilit ekranı kimlik doğrulamasını gerçekleştirmesine izin verecek şekilde saklanmalıdır *ZORUNLU*. Yukarı akışlı Android Açık Kaynak Projesi, bu gereksinimi karşılamak için kullanılabilecek Gatekeeper Donanım Soyutlama Katmanı (HAL) ve Trusty'yi sağlar.
- [C-1-4] MUST support key attestation where the attestation signing key is protected by secure hardware and signing is performed in secure hardware. Anahtarların cihaz tanımlayıcıları olarak kullanılmasını önlemek için, doğrulama imzalama anahtarlarının yeterli sayıda cihaz arasında paylaşılması ZORUNLUDUR. Bu gereksinimi karşılamanın bir yolu, belirli bir SKU'dan en az 100.000 birim üretilmediği sürece aynı doğrulama anahtarını paylaşmaktır. Bir SKU'nun 100.000 biriminden fazla üretilmesi durumunda her 100.000 birim için farklı bir anahtar KULLANILABİLİR.
Bir cihaz uygulaması daha önceki bir Android sürümünde zaten başlatılmışsa, bu tür bir cihazın, yalıtılmış bir yürütme ortamı tarafından desteklenen bir anahtar deposuna sahip olma ve android.hardware.fingerprint
doğrulamayı destekleme gerekliliğinden muaf tutulacağını unutmayın; yalıtılmış bir yürütme ortamı tarafından desteklenen bir anahtar deposu gerektirir.
- [C-1-5] MUST allow the user to choose the Sleep timeout for transition from the unlocked to the locked state, with a minimum allowable timeout up to 15 seconds. Automotive devices, that lock the screen whenever the head unit is turned off or the user is switched, MAY NOT have the Sleep timeout configuration.
- [C-1-6] MUST support IKeymasterDevice 4.0, IKeymasterDevice 4.1 or IKeyMintDevice version 1.
- [C-SR-1] Is STRONGLY RECOMMENDED to support IKeyMintDevice version 1.
9.11.1. Secure Lock Screen and Authentication
The AOSP implementation follows a tiered authentication model where a knowledge-factory based primary authentication can be backed by either a secondary strong biometric, or by weaker tertiary modalities.
Cihaz uygulamaları:
- [C-SR-1] Are STRONGLY RECOMMENDED to set only one of the following as the primary authentication method:
- A numerical PIN
- An alphanumerical password
- A swipe pattern on a grid of exactly 3x3 dots
Note that the above authentication methods are referred as the recommended primary authentication methods in this document.
If device implementations add or modify the recommended primary authentication methods and use a new authentication method as a secure way to lock the screen, the new authentication method:
- [C-2-1] MUST be the user authentication method as described in Requiring User Authentication For Key Use .
If device implementations add or modify the authentication methods to unlock the lock screen if based on a known secret and use a new authentication method to be treated as a secure way to lock the screen:
- [C-3-1] The entropy of the shortest allowed length of inputs MUST be greater than 10 bits.
- [C-3-2] The maximum entropy of all possible inputs MUST be greater than 18 bits.
- [C-3-3] The new authentication method MUST NOT replace any of the recommended primary authentication methods (ie PIN, pattern, password) implemented and provided in AOSP.
- [C-3-4] The new authentication method MUST be disabled when the Device Policy Controller (DPC) application has set the password requirements policy via the DevicePolicyManager.setRequiredPasswordComplexity() with a more restrictive complexity constant than PASSWORD_COMPLEXITY_NONE or via the DevicePolicyManager.setPasswordQuality() method with a more restrictive constant than PASSWORD_QUALITY_BIOMETRIC_WEAK .
- [C-3-5] New authentication methods MUST either fall back to the recommended primary authentication methods (ie PIN, pattern, password) once every 72 hours or less OR clearly disclose to the user that some data will not be backed up in order to preserve the privacy of their data.
If device implementations add or modify the recommended primary authentication methods to unlock the lock screen and use a new authentication method that is based on biometrics to be treated as a secure way to lock the screen, the new method:
- [C-4-1] MUST meet all requirements described in section 7.3.10 for Class 1 (formerly Convenience ).
- [C-4-2] MUST have a fall-back mechanism to use one of the recommended primary authentication methods which is based on a known secret.
- [C-4-3] MUST be disabled and only allow the recommended primary authentication to unlock the screen when the Device Policy Controller (DPC) application has set the keyguard feature policy by calling the method
DevicePolicyManager.setKeyguardDisabledFeatures()
) , with any of the associated biometric flags (ieKEYGUARD_DISABLE_BIOMETRICS
,KEYGUARD_DISABLE_FINGERPRINT
,KEYGUARD_DISABLE_FACE
, orKEYGUARD_DISABLE_IRIS
).
If the biometric authentication methods do not meet the requirements for Class 3 (formerly Strong ) as described in section 7.3.10 :
- [C-5-1] The methods MUST be disabled if the Device Policy Controller (DPC) application has set the password requirements quality policy via the DevicePolicyManager.setRequiredPasswordComplexity() with a more restrictive complexity bucket than
PASSWORD_COMPLEXITY_LOW
or using DevicePolicyManager.setPasswordQuality() method with a more restrictive quality constant thanPASSWORD_QUALITY_BIOMETRIC_WEAK
. - [C-5-2] The user MUST be challenged for the recommended primary authentication (eg: PIN, pattern, password) as described in [C-1-7] and [C-1-8] in section 7.3.10 .
- [C-5-3] The methods MUST NOT be treated as a secure lock screen, and MUST meet the requirements that start with C-8 in this section below.
If device implementations add or modify the authentication methods to unlock the lock screen and a new authentication method is based on a physical token or the location:
- [C-6-1] They MUST have a fall-back mechanism to use one of the recommended primary authentication methods which is based on a known secret and meet the requirements to be treated as a secure lock screen.
- [C-6-2] The new method MUST be disabled and only allow one of the recommended primary authentication methods to unlock the screen when the Device Policy Controller (DPC) application has set the policy with either:
- The
DevicePolicyManager.setKeyguardDisabledFeatures(KEYGUARD_DISABLE_TRUST_AGENTS)
method - The
DevicePolicyManager.setPasswordQuality()
method with a more restrictive quality constant thanPASSWORD_QUALITY_NONE
. - The
DevicePolicyManager.setRequiredPasswordComplexity()
method with a more restrictive complexity bucket thanPASSWORD_COMPLEXITY_NONE
.
- The
- [C-6-3] The user MUST be challenged for one of the recommended primary authentication methods (egPIN, pattern, password) at least once every 4 hours or less.
- [C-6-4] The new method MUST NOT be treated as a secure lock screen and MUST follow the constraints listed in C-8 below.
Cihaz uygulamalarında güvenli bir kilit ekranı varsa ve TrustAgentService
System API'sini uygulayan bir veya daha fazla güven aracısı içeriyorsa bunlar:
- [C-7-1] MUST have clear indication in the settings menu and on the lock screen when device lock is deferred or can be unlocked by trust agent(s). For example, AOSP meets this requirement by showing a text description for the "Automatically lock setting" and "Power button instantly locks" in the settings menu and a distinguishable icon on the lock screen.
- [C-7-2] MUST respect and fully implement all trust agent APIs in the
DevicePolicyManager
class, such as theKEYGUARD_DISABLE_TRUST_AGENTS
constant. - [C-7-3] MUST NOT fully implement the
TrustAgentService.addEscrowToken()
function on a device that is used as a primary personal device (eg handheld) but MAY fully implement the function on device implementations that are typically shared (eg Android Television or Automotive device). - [C-7-4] MUST encrypt all stored tokens added by
TrustAgentService.addEscrowToken()
. - [C-7-5] MUST NOT store the encryption key or escrow token on the same device where the key is used. For example, it is allowed for a key stored on a phone to unlock a user account on a TV. For Automotive devices, it is not allowed for the escrow token to be stored on any part of the vehicle.
- [C-7-6] MUST inform the user about the security implications before enabling the escrow token to decrypt the data storage.
- [C-7-7] MUST have a fall-back mechanism to use one of the recommended primary authentication methods.
- [C-7-8] The user MUST be challenged for one of the recommended primary authentication (eg: PIN, pattern, password) methods at least once every 72 hours or less unless the safety of the user (eg driver distraction) is of kaygı.
- [C-7-9] The user MUST be challenged for one of the recommended primary authentication (eg: PIN, pattern, password) methods as described in [C-1-7] and [C-1-8] in section 7.3.10 , unless the safety of the user (eg driver distraction) is of concern.
- [C-7-10] MUST NOT be treated as a secure lock screen and MUST follow the constraints listed in C-8 below.
- [C-7-11] MUST NOT allow TrustAgents on primary personal devices (eg: handheld) to unlock the device, and can only use them to keep an already unlocked device in the unlocked state for up to a maximum of 4 hours. The default implementation of TrustManagerService in AOSP meets this requirement.
- [C-7-12] MUST use a cryptographically secure (eg UKEY2) communication channel to pass the escrow token from the storage device to the target device.
If device implementations add or modify the authentication methods to unlock the lock screen that is not a secure lock screen as described above, and use a new authentication method to unlock the keyguard:
- [C-8-1] The new method MUST be disabled when the Device Policy Controller (DPC) application has set the password quality policy via the
DevicePolicyManager.setPasswordQuality()
method with a more restrictive quality constant thanPASSWORD_QUALITY_NONE
or via theDevicePolicyManager.setRequiredPasswordComplexity()
with a more restrictive complexity constant than 'PASSWORD_COMPLEXITY_NONE'. - [C-8-2] They MUST NOT reset the password expiration timers set by
DevicePolicyManager.setPasswordExpirationTimeout()
. - [C-8-3] They MUST NOT expose an API for use by third-party apps to determine the lock state.
If device implementations support separate display power states through DeviceStateManager
AND support separate display lock states through KeyguardDisplayManager
, they:
- [C-SR-2] Are STRONGLY RECOMMENDED to utilize a credential meeting requirements defined in section 9.11.1 or a Biometric meeting at least Class 1 specifications defined in section 7.3.10 to allow independent unlocking from the default device display.
- [C-SR-3] Are STRONGLY RECOMMENDED to constrain separate display unlock via a defined display timeout.
- [C-SR-4] Are STRONGLY RECOMMENDED to allow user to globally lock all displays through lockdown from primary handheld device.
9.11.2. Kasa
The Android Keystore System allows app developers to store cryptographic keys in a dedicated secure processor as well as the isolated execution environment described above. Such a dedicated secure processor is called "StrongBox". Requirements C-1-3 through C-1-11 below define the requirements a device must meet to qualify as a StrongBox.
Device implementations that have a dedicated secure processor:
- [C-SR-1] Are STRONGLY RECOMMENDED to support StrongBox. StrongBox will likely become a requirement in a future release.
If device implementations support StrongBox, they:
[C-1-1] MUST declare FEATURE_STRONGBOX_KEYSTORE .
[C-1-2] MUST provide dedicated secure hardware that is used to back keystore and secure user authentication. The dedicated secure hardware may be used for other purposes as well.
[C-1-3] MUST have a discrete CPU that shares no cache, DRAM, coprocessors or other core resources with the application processor (AP).
[C-1-4] MUST ensure that any peripherals shared with the AP cannot alter StrongBox processing in any way, or obtain any information from the StrongBox. The AP MAY disable or block access to StrongBox.
[C-1-5] MUST have an internal clock with reasonable accuracy (+-10%) that is immune to manipulation by the AP.
[C-1-6] MUST have a true random number generator that produces uniformly-distributed and unpredictable output.
[C-1-7] MUST have tamper resistance, including resistance against physical penetration, and glitching.
[C-1-8] MUST have side-channel resistance, including resistance against leaking information via power, timing, electromagnetic radiation, and thermal radiation side channels.
[C-1-9] MUST have secure storage which ensures confidentiality, integrity, authenticity, consistency, and freshness of the contents. The storage MUST NOT be able to be read or altered, except as permitted by the StrongBox APIs.
To validate compliance with [C-1-3] through [C-1-9], device implementations:
- [C-1-10] MUST include the hardware that is certified against the Secure IC Protection Profile BSI-CC-PP-0084-2014 or evaluated by a nationally accredited testing laboratory incorporating High attack potential vulnerability assessment according to the Common Criteria Application of Attack Potential to Smartcards .
- [C-1-11] MUST include the firmware that is evaluated by a nationally accredited testing laboratory incorporating High attack potential vulnerability assessment according to the Common Criteria Application of Attack Potential to Smartcards .
- [C-SR-2] Are STRONGLY RECOMMENDED to include the hardware that is evaluated using a Security Target, Evaluation Assurance Level (EAL) 5, augmented by AVA_VAN.5. EAL 5 certification will likely become a requirement in a future release.
[C-SR-3] are STRONGLY RECOMMENDED to provide insider attack resistance (IAR), which means that an insider with access to firmware signing keys cannot produce firmware that causes the StrongBox to leak secrets, to bypass functional security requirements or otherwise enable access to sensitive user data. The recommended way to implement IAR is to allow firmware updates only when the primary user password is provided via the IAuthSecret HAL.
9.11.3. Identity Credential
The Identity Credential System is defined and achieved by implementing all APIs in the android.security.identity.*
package. These APIs allows app developers to store and retrieve user identity documents. Cihaz uygulamaları:
- [C-SR-1] are STRONGLY RECOMMENDED to implement the Identity Credential System.
If device implementations implement the Identity Credential System, they:
[C-1-1] MUST return non-null for the IdentityCredentialStore#getInstance() method.
[C-1-2] MUST implement the Identity Credential System (eg the
android.security.identity.*
APIs) with code communicating with a trusted application in an area that is securely isolated from the code running on the kernel and above. Güvenli izolasyon, çekirdek veya kullanıcı alanı kodunun, DMA dahil, izole edilmiş ortamın dahili durumuna erişebileceği tüm potansiyel mekanizmaları ENGELLEMELİDİR.[C-1-3] The cryptographic operations needed to implement the Identity Credential System (eg the
android.security.identity.*
APIs) MUST be performed entirely in the trusted application and private key material MUST never leave the isolated execution environment unless specifically required by higher-level APIs (eg the createEphemeralKeyPair() method).[C-1-4] The trusted application MUST be implemented in a way such that its security properties are not affected (eg credential data is not released unless access control conditions are satisfied, MACs can't be produced for arbitrary data) even if Android is misbehaving or compromised.
9.12. Data Deletion
All device implementations:
- [C-0-1] MUST provide users a mechanism to perform a "Factory Data Reset".
- [C-0-2] MUST delete all data on the userdata filesystem when performing a "Factory Data Reset".
- [C-0-3] MUST delete the data in such a way that will satisfy relevant industry standards such as NIST SP800-88 when performing a "Factory Data Reset".
- [C-0-4] MUST trigger the above "Factory Data Reset" process when the
DevicePolicyManager.wipeData()
API is called by the primary user's Device Policy Controller app. - MAY provide a fast data wipe option that conducts only a logical data erase.
9.13. Safe Boot Mode
Android provides Safe Boot Mode, which allows users to boot up into a mode where only preinstalled system apps are allowed to run and all third-party apps are disabled. This mode, known as "Safe Boot Mode", provides the user the capability to uninstall potentially harmful third-party apps.
Device implementations are:
- [C-SR-1] STRONGLY RECOMMENDED to implement Safe Boot Mode.
If device implementations implement Safe Boot Mode, they:
[C-1-1] MUST provide the user an option to enter Safe Boot Mode in such a way that is uninterruptible from third-party apps installed on the device, except when the third-party app is a Device Policy Controller and has set the
UserManager.DISALLOW_SAFE_BOOT
flag as true.[C-1-2] MUST provide the user the capability to uninstall any third-party apps within Safe Mode.
SHOULD provide the user an option to enter Safe Boot Mode from the boot menu using a workflow that is different from that of a normal boot.
9.14. Automotive Vehicle System Isolation
Android Automotive devices are expected to exchange data with critical vehicle subsystems by using the vehicle HAL to send and receive messages over vehicle networks such as CAN bus.
The data exchange can be secured by implementing security features below the Android framework layers to prevent malicious or unintentional interaction with these subsystems.
9.15. Abonelik Planları
"Subscription plans" refer to the billing relationship plan details provided by a mobile carrier through SubscriptionManager.setSubscriptionPlans()
.
All device implementations:
- [C-0-1] MUST return subscription plans only to the mobile carrier app that has originally provided them.
- [C-0-2] MUST NOT remotely back up or upload subscription plans.
- [C-0-3] MUST only allow overrides, such as
SubscriptionManager.setSubscriptionOverrideCongested()
, from the mobile carrier app currently providing valid subscription plans.
9.16. Application Data Migration
If device implementations include a capability to migrate data from a device to another device and do not limit the application data it copies to what is configured by the application developer in the manifest via android:fullBackupContent attribute, they:
- [C-1-1] MUST NOT initiate transfers of application data from devices on which the user has not set a primary authentication as described in 9.11.1 Secure Lock Screen and Authentication .
- [C-1-2] MUST securely confirm the primary authentication on the source device and confirm with the user intent to copy the data on the source device before any data is transferred.
- [C-1-3] MUST use security key attestation to ensure that both the source device and the target device in the device-to-device migration are legitimate Android devices and have a locked bootloader.
- [C-1-4] MUST only migrate application data to the same application on the target device, with the same package name AND signing certificate.
- [C-1-5] MUST show an indication that the source device has had data migrated by a device-to-device data migration in the settings menu. A user SHOULD NOT be able to remove this indication.
10. Software Compatibility Testing
Device implementations MUST pass all tests described in this section. However, note that no software test package is fully comprehensive. For this reason, device implementers are STRONGLY RECOMMENDED to make the minimum number of changes as possible to the reference and preferred implementation of Android available from the Android Open Source Project. This will minimize the risk of introducing bugs that create incompatibilities requiring rework and potential device updates.
10.1. Compatibility Test Suite
Cihaz uygulamaları:
[C-0-1] MUST pass the Android Compatibility Test Suite (CTS) available from the Android Open Source Project, using the final shipping software on the device.
[C-0-2] MUST ensure compatibility in cases of ambiguity in CTS and for any reimplementations of parts of the reference source code.
The CTS is designed to be run on an actual device. Like any software, the CTS may itself contain bugs. The CTS will be versioned independently of this Compatibility Definition, and multiple revisions of the CTS may be released for Android 12.
Cihaz uygulamaları:
[C-0-3] MUST pass the latest CTS version available at the time the device software is completed.
SHOULD use the reference implementation in the Android Open Source tree as much as possible.
10.2. CTS Verifier
The CTS Verifier is included with the Compatibility Test Suite, and is intended to be run by a human operator to test functionality that cannot be tested by an automated system, such as correct functioning of a camera and sensors.
Cihaz uygulamaları:
- [C-0-1] MUST correctly execute all applicable cases in the CTS verifier.
The CTS Verifier has tests for many kinds of hardware, including some hardware that is optional.
Cihaz uygulamaları:
- [C-0-2] MUST pass all tests for hardware that they possess; for instance, if a device possesses an accelerometer, it MUST correctly execute the Accelerometer test case in the CTS Verifier.
Test cases for features noted as optional by this Compatibility Definition Document MAY be skipped or omitted.
- [C-0-2] Every device and every build MUST correctly run the CTS Verifier, as noted above. However, since many builds are very similar, device implementers are not expected to explicitly run the CTS Verifier on builds that differ only in trivial ways. Specifically, device implementations that differ from an implementation that has passed the CTS Verifier only by the set of included locales, branding, etc. MAY omit the CTS Verifier test.
11. Updatable Software
[C-0-1] Device implementations MUST include a mechanism to replace the entirety of the system software. The mechanism need not perform “live” upgrades—that is, a device restart MAY be required. Any method can be used, provided that it can replace the entirety of the software preinstalled on the device. For instance, any of the following approaches will satisfy this requirement:
- “Over-the-air (OTA)” downloads with offline update via reboot.
- “Tethered” updates over USB from a host PC.
- “Offline” updates via a reboot and update from a file on removable storage.
[C-0-2] The update mechanism used MUST support updates without wiping user data. That is, the update mechanism MUST preserve application private data and application shared data. Note that the upstream Android software includes an update mechanism that satisfies this requirement.
[C-0-3] The entire update MUST be signed and the on-device update mechanism MUST verify the update and signature against a public key stored on device.
[C-SR-1] The signing mechanism is STRONGLY RECOMMENDED to hash the update with SHA-256 and validate the hash against the public key using ECDSA NIST P-256.
If the device implementations includes support for an unmetered data connection such as 802.11 or Bluetooth PAN (Personal Area Network) profile, then, they:
- [C-1-1] MUST support OTA downloads with offline update via reboot.
Device implementations SHOULD verify that the system image is binary identical to the expected result following an OTA. The block-based OTA implementation in the upstream Android Open Source Project, added since Android 5.1, satisfies this requirement.
Also, device implementations SHOULD support A/B system updates . The AOSP implements this feature using the boot control HAL.
If an error is found in a device implementation after it has been released but within its reasonable product lifetime that is determined in consultation with the Android Compatibility Team to affect the compatibility of third-party applications, then:
- [C-2-1] The device implementer MUST correct the error via a software update available that can be applied per the mechanism just described.
Android includes features that allow the Device Owner app (if present) to control the installation of system updates. If the system update subsystem for devices report android.software.device_admin then, they:
- [C-3-1] MUST implement the behavior described in the SystemUpdatePolicy class.
12. Document Changelog
For a summary of changes to the Compatibility Definition in this release:
For a summary of changes to individuals sections:
- giriiş
- Device Types
- Yazılım
- Application Packaging
- Multimedya
- Developer Tools and Options
- Hardware Compatibility
- Performans ve Güç
- Güvenlik Modeli
- Software Compatibility Testing
- Updatable Software
- Document Changelog
- Bize Ulaşın
12.1. Changelog Viewing Tips
Changes are marked as follows:
CDD
Substantive changes to the compatibility requirements.Dokümanlar
Cosmetic or build related changes.
For best viewing, append the pretty=full
and no-merges
URL parameters to your changelog URLs.
13. Contact Us
You can join the android-compatibility forum and ask for clarifications or bring up any issues that you think the document does not cover.